wifi_mod_para_powersave.conf in order to avoid requesting
high ddr frequency when using WIFI. The above problem does
not exist after the kernel version is greater than v5.4.
Change-Id: Iac0f3bcbb325f9d4603863d84c217cbecb3106db
Signed-off-by: Zhipeng Wang <zhipeng.wang_1@nxp.com>
Updated firmware:
SDIO-UART W8987 Firmware version 16.92.21.p76.2
PCIE-UART W8997 Firmware version 16.92.21.p76.2
SDIO-UART W8997 Firmware version 16.92.21.p76.2
SDIO-UART IW416 Firmware version 16.92.21.p76.3
SDIO_UART IW612 Firmware version 18.99.1.p154.40
SDIO-UART W8801 Firmware version 14.92.36.p180
SDIO-UART W9098 Firmware version 17.92.1.p136.24
PCIE-UART W9098 Firmware version 17.92.1.p136.24
WLAN new Additions/Removals/Improvements:
---------------
1. SD8987: WSFD-443: Clock synch feature
WLAN Bug Fixes:
---------------
1. SD8987/PCIE8997/IW416: WSW-24682: Ping is failing between testbed STA and STAUT after GTK rekey from AP
2. SD8987/PCIE8997/IW416: WSW-23252: Carrier sense test on Japanese regulation fail
3. SD8987: WSW-24668: STAUT is sending unprotected BTM/WNM action frames
4. SD8987: WSW-24629: Add support for antenna diversity control using gpio
5. SD8987: WSFD-658: Annex 106 - GPIO based FEM control via SOC register programming
6. SD8987: WSW-23926: UDP RX is lower than 5Mbps when playing music in shielding room
7. SD8987: WSW-22542: WiFi hang up with diff command timeout during run BT Inband/outband IR test w/ WiFi activities
8. SD8987/IW416: WSFD-653: Enable AES in FW by default
9. SD8987: WSW-23252 WSW-24023 Fix for probe resp and beacon leak
10. SD8987: WSFD-494: WiFi won't be connected back immediately when screen is off
11. PCIE8997: WSW-23539: Disconnection with reason 15 during WPA re-keying
12. PCIE8997: WSW-23252 WSW-24023: Fix for probe resp and beacon leak
13. IW416: WSW-23771: WLAN deauthentication observed if A2DP suspended and started again
14. IW416: WSW-23957: MMHAP Unable make connection with NXP Reference Devices
15. IW612: WSW-23908: Observing device hang issue when doing channel switch for MMH with open security
16. IW612: WSW-24518: 100% chload sometimes if EDMAC is enabled and any STA is connected
17. IW612: WCSWREL-413: P2P cannot work with the latest firmware
18. PCIE9098/SD9098: WCSWREL-414: P2P cannot work and observe command timeout
19. PCIE9098: Wakeup card timeout after suspend/resume
20. PCIE9098/SD9098: WSFD-599: Support trigger frame generating in RF test mode
BT/Co-ex Bug Fixes:
-------------------
1. SD8987: WSW-22599: Audio glitch could be heard when ACL is Master role(BT only scenario) in Congestion environment
2. IW416: WSW-23661: LE power capping to 10 dBm needs to be revoked for silicon supporting BT 5.0 and higher versions
3. IW416: WSW-24502: Audio is not heard in TX direction during incoming/outgoing NBS call with Ref device
4. IW416: WSW-21498: Heavy A2DP Audio Distortion (Glitch in every ~1sec) observed when DUT is at 5 meter distance from reference device
5. IW416: WSW-22879: 2nd BT(S) link failed to establish in the presence of SCO/eSCO connection on the first(M) link
6. IW416: WSW-19213: After starting BT/BLE Tx, Tx response is observed momentarily on litepoint
7. IW416: WSW-24321: "Unknown HCI Command " returned as status for cmd "3f fc 00" to enable Independent Reset via in-Band
8. IW416: WSW-25052: FW not getting up after enabling Independent Reset via in-Band
9. IW416: WSW-24024: Wlan De-authentication Observed while STA/MMH+LE Scan Coex Scenario
10. IW416: WSW-24825: DUT not responding to the pair/connect request sent by the reference device
11. PCIE8997: WSW-24482: Random mute pattern observed during A2DP_SRC streaming with Ref1 when OPP_TX started with Ref2
12. PCIE8997: WSW-18190: Issue observed in BT Paging /LE Connection + MMH/STA[BGN20] with Wifi RX traffic
13. IW612: WSW-23062: Speaker Disconnection while switching A2DP streaming between two speakers
14. IW612: WSW-23992: Frequent Page timeout (0x04) observed in DUT for Create_Connection command in scatternet scenarios
15. IW612: WSW-24302: Severe A2DP glitches are observed while connecting disconnecting A2DP-SNK devices
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Updated firmware:
SDIO-UART W8987 Firmware version 16.92.21.p76
PCIE-UART W8997 Firmware version 16.92.21.p76
SDIO-UART W8997 Firmware version 16.92.21.p76
SDIO-UART IW416 Firmware version 16.92.21.p76
SDIO_UART IW612 Firmware version 18.99.1.p154.18
Unchanged firmware:
SDIO-UART W8801 Firmware version 14.92.36.p178
SDIO-UART W9098 Firmware version 17.92.1.p136.13
PCIE-UART W9098 Firmware version 17.92.1.p136.13
WLAN new Additions/Removals/Improvements:
---------------
1. SD8987/IW416: WiFi Agile Multi-Band
2. SD8987: Monitor Mode
3. SD8987/IW416: uAPSD / PPS
4. SD8987: Packet Coalescing
5. SD8987/IW416: Support Boot Sleep Patch
6. PCIE8997/SD8997/IW416: Enable Wifi Easy Connect (DPP)
7. PCIE8997/SD8997: Wi-Fi Enhanced Open (OWE)
8. PCIE8997/SD8997/IW416: WPA3 embedded
9. PCIE8997/SD8997/IW416: mDNS (Bonjour) Offload - Wi-Fi
10. PCIE8997/SD8997/IW416: IPv6 NS Offload
11. PCIE8997/SD8997/IW416: Auto Reconnect
12. PCIE8997/SD8997: Independent reset via inband
13. PCIE8997/SD8997: Enable Independent Reset via Out-of-Band
WLAN Bug Fixes:
---------------
1. SD8987: WSW-23818: Fixed the DFS channel failure
2. SD8997: WSW-23254: auto_tx Feature fails with seconds interval configuration
3. SD8997: WSW-19809: less TP observed in P2P- 11AC/AN/BGN, TCP/UDP, TX/RX
4. IW612: WSW-23423: WLAN+BT Parallel download and Combo FW download consuming more current compared to BT+WLAN
5. IW612: WSW-21650: False radar detection when IW620 transmitting
6. IW612: WSW-22003: Low throughput was observed in 2.4G-Tx when Netgear AP 20/40 MHz coexistence was enabled
BT/COEX New Additions/Removals/Improvements:
-------------------
1. SD8987/PCIE8997/SD8997: BT/BLE Deepsleep
2. PCIE8997: Wake on BLE
3. IW416: BLE Multi-Adv / Advertisement Extension
4. IW416: LE Long Range
BT/Co-ex Bug Fixes:
-------------------
1. SD8987: WSW-23234: BREDR qualification TCs failure
2. SD8987: WSW-23233: BLE qualification TCs failures
3. SD8987: WSW-21475: Only one headset can hear the voice after establish two esco links during DUAL HFP test
4. SD8987: WSW-23110: Pairing failure when connecting with nRF connect app from mobile phone
5. SD8987: WSW-22242: Sometimes BT firmware is downloaded successfully, but cannot active and WIFI scan command will timeout
6. PCIE8997/SD8997: WSW-19165: New BREDR TCs and failures with TCRL2021-1 and TCRL2021-2
7. PCIE8997/SD8997: WSW-19166: New BLE TCs and failures with TCRL2021-1 and TCRL2021-2
8. PCIE8997/SD8997: WSW-20158: Disconnection with reason 15 during WPA re-keying
9. PCIE8997/SD8997: WSW-21809: Both OPP & HFP links drop when DUT starts OPP-TX transfer
10. IW416: WSW-22293: BluetoothLeAdvertiserTest cases fails during CTS run
11. IW416: WSW-19098: New BREDR TCs and failures with TCRL2021-2, E17535
12. IW416: WSW-19164: New BLE TCs and failures with TCRL2021-2, E17535
13. IW416: WSW-22605: DUT displaying wrong LMP Version i.e 5.0 instead of 5.3
14. IW612: WSW-23431: DUT hangs during execute LL TCs ,hard to continue the Qual testing
15. IW612: WSW-21751: No eSCO connection complete event after remote device reject eSCO connection
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
0x0e is the recommend Energy Detect threshold for muRata 2DS module,
otherwise the inappropriate ed_mac value may cause 2.4G channel 1 AP/P2P
function cannot work when use 2DS along with muRata M.2-usd apater.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Updated firmware:
SDIO-UART W8987 Firmware version 16.92.21.p69.3
SDIO-UART W9098 Firmware version 17.92.1.p136.13
PCIE-UART W9098 Firmware version 17.92.1.p136.13
Unchanged firmware:
SDIO-UART W8801 Firmware version 14.92.36.p178
PCIE-UART W8997 Firmware version 16.92.21.p55.3
SDIO-UART W8997 Firmware version 16.92.21.p55.3
SDIO-UART IW416 Firmware version 16.92.21.p55.3
WLAN Bug Fixes:
---------------
1. PCIE9098/SD9098: WSW-22305: wifi cmd timeout showed when test switch connect with different APs
2. PCIE9098/SD9098: WSW-20645: DUT fails to reassociate when Ex-AP changes its channel to 149/HE80
3. PCIE9098/SD9098: WSW-20819: detect a spike on spectrum during CAC
4. PCIE9098/SD9098: WSW-22448: High Channel Load seen in getchload command in APUT when it is receiving full bandwidth UDP Rx traffic
5. PCIE9098/SD9098: WSW-20549: Scan CMD Timeout 0x107 observed on 9098 STA when attempting to associate with 9098 uAP
6. PCIE9098/SD9098: WSW-22460: DUT send RTS packet during RTS threshold boundary test
7. PCIE9098/SD9098: WSW-20734: In-STA associates in VHT20 instead of VHT40 using mlan0 interface to Ex-AP configured in HE80/VHT80 mode
8. PCIE9098/SD9098: WSW-21097: 0x5e Command timeout observed, while running connect disconnect with multiclient (8 clients) after 1 hour
9. PCIE9098/SD9098: WSW-22158: False Radar flood observed on Aux Path
10. PCIE9098/SD9098: WSW-20625: External station can't connect with 5G uAP interface after long time standby
11. PCIE9098/SD9098: WSW-22012: Disable JTAG in SW to meet various security requirements.
12. PCIE9098/SD9098: WSW-20445: extAP-wpa23 and mmlan-wpa12 ping aging dis-connect
13. PCIE9098/SD9098: WSW-21983: STA in 2.4GHz not connecting to Ex-AP from Android HMI
14. PCIE9098/SD9098: WSW-22216: 0x107 command timeout when kept staying on Wi-Fi setting GUI with STA connected
15. SD8987: WSW-21659: cmd timeout happen after DUT switches to New DFS channel
16. SD8987: WSW-19978: DUT hang observed while streaming A2DP music after launching "truncated_sco_link_request" exploiter using Braktooth
17. SD8987: WSW-21879: Fixed the issue of false radar detection
18. SD8987: WSW-20347: Frequent false radar detect in CH52 VH40 when Ext AP in CH60 nearby
19. SD8987: WSW-22596: FP92+ release 2G/5G WAPI connected failed
BT/Co-ex Bug Fixes:
-------------------
1. PCIE9098/SD9098: WSW-23264: Command timeout happens for vendor command HCI_CMD_MRVL_HOST_PCM_CONFIG(0x6F)
2. PCIE9098/SD9098: WSW-21142: Random command timeout when performing connection & disconnection with remote phone in a loop
3. PCIE9098/SD9098: WSW-18717: Severe A2DP glitches observed for Play-Pause on REF2 during active HFP on REF1
4. PCIE9098/SD9098: WSW-22782: LE link drop with reason "Instant Passed" during LE Disconnection (DUT role Slave)
5. PCIE9098/SD9098: WSW-22312: Audio is not heard in both Tx/Rx direction during incoming/outgoing WBS call with Ref device
6. PCIE9098/SD9098: WSW-16791: Non-supported LE Features are still observed as supported as part of MM release
7. PCIE9098/SD9098: WSW-22296: DUT unable to do LE Scan on nRF APP for GATT Outgoing connection
8. PCIE9098/SD9098: WSW-22419: In dual HFP connection Timeout issue is observed with the eSCO links
9. PCIE9098/SD9098: WSW-20203: Inquiry Scan failed 2 out of 5 times while STA/MMH iPerf traffic
10. PCIE9098/SD9098: WSW-20437: Severe A2DP glitches observed after disconnecting the SCO Bridge call
11. PCIE9098/SD9098: WSW-18024: Auto enable PCM configurations for Android
12. PCIE9098/SD9098: WSW-18065: FW hang observed during DUAL HF scenario verification
13. SD8987: WSW-23190: "Memory Capacity Exceeded" can be found if add the 5th device to the BLE Resolving List
14. SD8987: WSW-22380: BT crash observed, unable to recover while creating 4/5 LE connection
15. SD8987: WSW-22100: DUT as configurator, Initiator fail to AUTH CCT1(configurator) with PKEX way
16. SD8987: WSW-21481: Second device failed to be paired/connected during first device doing HFP outgoing call
17. SD8987: WSW-20418: DUT hang observed while streaming A2DP music after launching "feature_req_ping_pong" exploiter using Braktooth
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Updated firmware:
SDIO-UART W8987 Firmware version 16.92.21.p69
SDIO-UART W9098 Firmware version 17.92.1.p136.3
PCIE-UART W9098 Firmware version 17.92.1.p136.3
SDIO-UART W8801 Firmware version 14.92.36.p178
Unchanged firmware:
PCIE-UART W8997 Firmware version 16.92.21.p55.3
SDIO-UART W8997 Firmware version 16.92.21.p55.3
SDIO-UART IW416 Firmware version 16.92.21.p55.3
WLAN new Additions/Removals/Improvements:
---------------
1. PCIE9098/SD9098: DL-MUMIMO (STA Only)
2. PCIE9098/SD9098: UL-MUMIMO (STA Only)
3. PCIE9098/SD9098: Extended Range
4. PCIE9098/SD9098: 802.11k
5. PCIE9098/SD9098: 802.11v
6. PCIE9098/SD9098: 802.11z (Host based TDLS)
7. PCIE9098/SD9098: P2P for Miracast
8. PCIE9098/SD9098/SD8987: Wi-Fi Enhanced Open (OWE)
9. PCIE9098/SD9098: Clocksync
10. PCIE9098/SD9098/SD8987: Wireless Apple Car Play (R5)
11. PCIE9098/SD9098: Wireless Android Auto
12. PCIE9098/SD9098: Non-Triggered Target Wake Time
13. PCIE9098/SD9098: 802.11r (STA Roaming Support)
14. PCIE9098/SD9098: DCM
15. PCIE9098/SD9098: 802.11mc / Location
16. PCIE9098/SD9098: Easy Mesh
17. PCIE9098/SD9098: DRCS
18. PCIE9098/SD9098/SD8987: Wi-Fi Easy Connect (DPP)
19. PCIE9098/SD9098: DFS (Radar Detection) Master
20. PCIE9098/SD9098: uAPSD / PPS
21. PCIE9098/SD9098: Zero Wait DFS
22. PCIE9098/SD9098/SD8987: WAPI
23. PCIE9098/SD9098: Wi-Fi Agile Multi-Band
24. PCIE9098/SD9098: Packet Coalescing
25. PCIE9098/SD9098: WPA3 embedded
26. PCIE9098/SD9098: Embedded Authenticator
27. PCIE9098/SD9098: Embedded Supplicant
28. SD8987: mDNS offload
29. SD8987: ARP Offload
30. SD8987: mDNS (Bonjour) wake up - Wi-Fi
31. SD8987: IPv6 NS Offload
WLAN Bug Fixes:
---------------
1. SD8987: WSW-19887: First SAE commit exchange is not successful when TB STA sends SAE commit msg including APUT's anticlogging token
2. SD8987: WSW-21709: New txpower config not used when receiving new regulatory setting from AP
3. SD8987: WSW-19821: Connection fail about OWE-5.2.4 with wpa_v2.10-M001
4. SD8987: WSW-21085: STAUT is not setting Link Measurement bit in RRM Capabilities in Assoc Request
5. SD8987: WSW-21153: Release fw load fail when load with fw_serial=1 for the second time
6. SD8987: WSW-22107: DUT as Configurator AP configures enrollee as STA Fail
7. SD8801: WCSWREL-302: Enable WLAN time BT time to control GRANT
8. SD8801: WSW-18346: Enable External Coex Feature
9. SD8801: WSW-13649: DUT is not initiating association after succesful SAE authentication
10. SD8801: WSW-11577: STAUT not transmiting SAE confirm message when AP immediately transmits SAE confirm message after sendings it
11. SD8801: WSW-16956: WFA SVD failure fix MM
12. SD8801: WSW-16935: WPA3 R3 Support for MM
13. SD8801: WSW-13637: Rx-AMSDU & Rx-Frag related vulnerability applicability analysis & fixes
14. SD8801: WSW-14117: STA cannot connect with WPA2 AP at the first attempt
BT/COEX New Additions/Removals/Improvements:
-------------------
1. PCIE9098/SD9098/SD8987: Wake on BT/BLE (Chip to Host wake up)
2. PCIE9098/SD9098: Dual A2DP (2 Source)
3. PCIE9098/SD9098: Dual A2DP (1 Source + 1 Sink)
4. PCIE9098/SD9098: Dual HFP (1 WBS/1NBS) PCM
5. PCIE9098/SD9098/SD8987: Dual HFP (2 NBS) PCM
6. PCIE9098/SD9098: Support for alternate Codecs (AAC, LDAC)
7. PCIE9098/SD9098: External Coex
8. PCIE9098/SD9098: BCA Time Sharing Coex
9. PCIE9098/SD9098/SD8987: BLE Multi-Adv
10. SD8987: A2DP (SRC + SNK)
BT/Co-ex Bug Fixes:
-------------------
1. PCIE9098/SD9098: WSW-17756: Authentication Failure (0x05) is observed for BT connection during LE incoming connection + Bonding
2. PCIE9098/SD9098: WSW-18312: In Obexctl connect command is not working after giving the command for the second time
3. SD8987: WSW-19344: Audio Loss observed for 5-10s in between HFP call after launching "feature_response_flooding" exploiter using Braktooth
4. SD8987: WSW-19674: RX TP is lower than 1Mbps or could hear glitch when testing dual A2DP in open air and shielding room
5. SD8987: WSW-17584: New BLE TCs and failures with TCRL2021-1 and TCRL2021-2
6. SD8987: WSW-17585: New BREDR TCs and failures with TCRL2021-1 and TCRL2021-2
7. SD8987: WSW-19300: DUT hang observed after Severe A2DP Glitches and audio loss while streaming after launching "au_rand_flooding" exploiter using Braktooth
8. SD8987: WSW-19315: Severe A2DP Glitches observed while streaming after launching "invalid_timing_accuracy" exploiter using Braktooth
9. SD8987: WSW-19977: DUT hang observed while streaming A2DP music after launching "invalid_max_slot" exploiter using Braktooth
10. SD8987: WSW-20230: "Command disallowed" issue happens for Batch_scan_data_read command after set batch_scan_mode as 0 in Set_scan_parameter
11. SD8987: WSW-20287: UUT failed to reset after hciattach to 115200 because of unknown HCI command returned when Bluez host send get MWS transport layer configuration command
12. SD8987: WSW-21456: DUT is creating eSCO link even if host rejected second incoming eSCO link request during Dual HFP test
13. SD8987: WSW-20273: WBS sample rate was not set in daemon.conf
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Updated firmware:
PCIE-UART W8997 Firmware version 16.92.21.p55.3
SDIO-UART W8997 Firmware version 16.92.21.p55.3
SDIO-UART IW416 Firmware version 16.92.21.p55.3
Unchanged firmware:
SDIO-UART W8987 Firmware version 16.92.21.p41.4
SDIO-UART W9098 Firmware version 17.92.1.p116.1
PCIE-UART W9098 Firmware version 17.92.1.p116.1
SDIO-UART W8801 Firmware version 14.92.36.p174
WLAN Bug Fixes:
---------------
1. PCIE8997/SD8997/IW416: WCSWREL-368/WSW-21865: STA side WoWLAN Test fails as Host is not waking up after unicast ping
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Updated firmware:
PCIE-UART W8997 Firmware version 16.92.21.p55.2
SDIO-UART W8997 Firmware version 16.92.21.p55.2
SDIO-UART IW416 Firmware version 16.92.21.p55.1
SDIO-UART W8987 Firmware version 16.92.21.p41.4
Unchanged firmware:
SDIO-UART W9098 Firmware version 17.92.1.p116.1
PCIE-UART W9098 Firmware version 17.92.1.p116.1
SDIO-UART W8801 Firmware version 14.92.36.p174
WLAN Bug Fixes:
---------------
1. PCIE8997/SD8997: WSW-21404: Support for SSID field in neighbor request command is not present
2. PCIE8997/SD8997: WSW-19887: WPA3-R3 1st SAE commit (M1) not able to succeed
3. PCIE8997/SD8997: WSW-21196: P2P client disconnect with P2P GO when In-STA connecting to Ex-AP with different P2P GO channel
4. PCIE8997/SD8997: WSW-20725: In-STA don't send association request while setting pscfg DTIM interval from 1 to 3
5. PCIE8997/SD8997: WSW-20061: Duplicate HT/VHT IE seen in beacon of P2P GO
6. IW416: WSW-21196: P2P client disconnect with P2P GO when In-STA connecting to Ex-AP with different P2P GO channel
7. IW416: WSW-20061: Duplicate HT/VHT IE seen in beacon of P2P GO
8. IW416: WSW-19335: RSN Extension IE is not included in Assoc req when AP side does not connect via WPA3 R3
9. IW416: WSW-20788: Radar Detection Probability is below 60% for all ETSI
10. IW416: WSW-21404: Support for SSID field in neighbor request command is not present
11. IW416: WSW-11603: MMH fails to detect Radar signals in JP W56 Region
12. IW416: WSW-12993: DFS Support is required for New JP W53 Radar
13. IW416: WSW-19887: WPA3-R3 1st SAE commit (M1) not able to succeed
14. IW416: WSW-20725: In-STA don't send association request while setting pscfg DTIM interval from 1 to 3
BT/Co-ex Bug Fixes:
-------------------
1. PCIE8997/SD8997: WSW-20601: DUT hang observed after Severe A2DP Glitches and audio loss after launching invalid_max_slot exploiter
2. PCIE8997/SD8997: WSW-19719: LE advertising stopped unexpectedly
3. PCIE8997/SD8997: WSW-20971: DUT won't reply the received 2Mbps LLCP Date length Update Request and stop responding new RX pkt any longer
4. PCIE8997/SD8997: WSW-18231: Not able to get any packet received counts, RSSI, PER information for BT RX and packet received counts for BLE RX
5. SD8987: WSW-20157: DUT assigned same connection Handle to two different LE Remote Devices in dual mode
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Remove the mac_addr configuration for SD9098 and PCIE9098, as this
configuration will cause the 88w9098 devices fail to get the IP address
from the AP when test multiple 88w9098 devices at the same time.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
We need to use A1 secure mode firmware for IW612 in the formal release.
Also rename FwImage_IW612_SD/WlanCalData.conf to WlanCalData_IW612.conf.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Updated firmware:
PCIE-UART W8997 Firmware version 16.92.21.p55.1
SDIO-UART W8997 Firmware version 16.92.21.p55.1
SDIO-UART IW416 Firmware version 16.92.21.p55
Unchanged firmware:
SDIO-UART W9098 Firmware version 17.92.1.p116.1
PCIE-UART W9098 Firmware version 17.92.1.p116.1
SDIO-UART W8987 Firmware version 16.92.21.p41.3
SDIO-UART W8801 Firmware version 14.92.36.p174
WLAN new Additions/Removals/Improvements:
---------------
1. PCIE8997/SD8997: WSW-19003: 802.11z (Host based TDLS)
2. PCIE8997/SD8997: WSW-17793: Enable 802.11k and 802.11v
3. PCIE8997/SD8997: WSW-17801: Enable DFS (Radar Detection) Master
4. PCIE8997/SD8997: WSW-17809: Enable P2P for Miracast
5. PCIE8997/SD8997: WSW-19002: 802.11r (STA Roaming)
6. PCIE8997/SD8997: WSW-19007: Embedded Authenticator
7. PCIE8997/SD8997: WSW-19008: Embedded Supplicant
8. PCIE8997/SD8997: WSW-19015: Enable FIPS
9. IW416: WSW-19021: Enable 802.11k
10. IW416: WSW-19022: Enable 802.11v
11. IW416: WSW-19025: Enable DFS (Radar Detection) Master
12. IW416: WSW-19027: Embedded Authenticator
13. IW416: WSW-19028: Embedded Supplicant
14. IW416: WSW-19023: 802.11r (STA Roaming)
WLAN Bug Fixes:
---------------
1. PCIE8997: WSW-17438: Wake up card timeout occurs during OTT box power on
2. PCIE8997: WSW-18483: EU Cert needs to pass with Option A
3. PCIE8997: WSW-18347: 0x10d CMD Timeout occurs when In-STA connecting 2.4G Ex-AP or running TCP Tx iperf throughput while A2DP music is playing
4. PCIE8997: WSW-18236: Beamforming packets are not getting filtered in HT20 in CSI record
5. PCIE8997: WSW-18323: CSI records not captured on un-associate state
6. PCIE8997: WSW-18326: uAP bring-up on DFS in uAP+STA simultaneous mode
7. PCIE8997: WSW-18327: CAC starts on the MMH for DFS when STA on DFS channel in uAP+STA simultaneous mode
8. SD8997: WSW-19820: STA sends deauth to Ex-AP shortly after connection
9. SD8997: WSW-19858: STA reported link lost event shortly after connection
10. SD8997: WSW-19944: STA occurs auth timeout frequently while trying to connect to Ex-AP
11. SD8997: WSW-20060: AW-CM276MA-PUR 5G CH155 Rx sensitivity is less compared to 8997 MFG FW on antenna Aux port
12. SD8997: WSW-20118: Duplicate frame of HT Cap , VHT Cap, HT info and VHT info is present in Beacons
13. SD8997: WSW-20140: Deauth occurs during connecting to Ex-AP
14. SD8997: WSW-20277: STA occurs 0x107/0xd0 command timeout while doing security Fuzz testing
15. SD8997: WSW-20394: In-STA doesn't response Ex-AP's "Message 1 of 4" EAPOL frame until FW link lost occurs
16. IW416: WSW-17943: Failed to create uAP if ED MAC offset is set to 0x1C at 5G with HT40
17. IW416: WSW-18928: Suspend_Resume stress failed with error -16
18. IW416: WSW-19138: DUT is not able to re-associate with EX-AP with Android GUI automatically after removal of interference signal
19. IW416: WSW-19659: connection WPA2-EAP TTLS and WPA/WPA2-EAP TTLS FAILS but EAP -TLS Passing
20. IW416: WSW-19787: MMH fails to start in Channel 100
21. IW416: WSW-19807: IW416_Type1XK_64ch_RF performance issue with rf_test_mode
22. IW416: WSW-19970: Data/Beacon Frame leakage seen after application of interference signal in 2G for both STA/MMH Mode
BT/COEX New Additions/Removals/Improvements:
-------------------
1. PCIE8997/SD8997: WSW-19006: BCA Time Sharing Coex
2. PCIE8997/SD8997: WSW-19009: BLE Multi-Adv
3. IW416: WSW-19026: BCA Time Sharing Coex
4. IW416: WSW-19029: External Coex
BT/Co-ex Bug Fixes:
-------------------
1. PCIE8997: WSW-11660: LMP Response TO is observed after ref phone initiates disconnection of ACL after eSCO connection fails to establish
2. PCIE8997: WSW-15020: During MMH TCP_RX/UDP_RX traffic BT-HID_GW data gets stuck
3. PCIE8997: WSW-16791: Non-supported LE Features are still observed as supported as part of MM release
4. PCIE8997: WSW-16992: Link loss (Connection TO/LMP Response Timeout) is observed during the connection with iPhone 11/iPhone 12 Mini
5. PCIE8997: WSW-17440: low WLAN throughputs observed in lescan coex scenario
6. PCIE8997: WSW-17442: low WLAN throughputs observed in A2DP SRC and SINK coex scenario
7. PCIE8997: WSW-18272: OPP-Tx file transfer is failed during STA connected in 2.4GHz BGN-20
8. PCIE8997: WSW-18522: Audio is not heard in both Tx/Rx direction during incoming WBS call with iphone-12 mini
9. PCIE8997: WSW-19252: DUT hang observed after Severe A2DP Glitches and audio loss after launching "au_rand_flooding" exploiter
10. SD8997: WSW-18188: Low TP observed in OPP-TX + STA(HT20) with WLAN RX Traffic
11. SD8997: WSW-18189: Issue observed in BT Paging /LE Connection + MMH[BGN20] with Wifi RX traffic
12. SD8997: WSW-18197: 2M PHY value option is disabled with default libbluetooth.so file in the nrf app
13. SD8997: WSW-19794: Audio distortion observed in HFP call when OPP_Tx data transfer started
14. SD8997: WSW-19917: VTS test cases are getting fail when BLE wakeup host feature is enabled
15. SD8997: WSW-19939: OPP_Rx File transfer is not successful and once transfer unsuccessful, Bluetooth is turned off automatically
16. IW416: WSW-13709: A2DP_SRC Streaming got suspended automatically with Hardware Error
17. IW416: WSW-16791: Non-supported LE Features are still observed as supported as part of MM release
18. IW416: WSW-17191: Grant is de-asserted by IW416 before Request is de-asserted by K32W
19. IW416: WSW-19308: After Disconnection, Failed to reconnect Reference device through PAN profile from DUT
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Updated firmware:
SDIO-UART W9098 Firmware version 17.92.1.p116.1
SDIO-UART W8987 Firmware version 16.92.21.p41.3
SDIO-UART IW416 Firmware version 16.92.21.p41.1
PCIE-UART W9098 Firmware version 17.92.1.p116.1
Unchanged firmware:
SDIO-UART W8801 Firmware version 14.92.36.p174
SDIO-UART W8997 Firmware version 16.92.21.p41
PCIE-UART W8997 Firmware version 16.92.21.p26.1
WLAN Bug Fixes:
---------------
1. SD8987: WSW-19750: Fix Low radar detection rate in 20MHz [JP56]
2. SD8987: WSW-19629: Fix Radar dectection rate very low in CH52 for VHT40 [ETSI]
3. SD8987: WSW-19729: Fix Low radar detection rate on some channels in 40MHz [FCC]
4. SD8987: WSW-11606: Fix KCC type 2 low radar detection probability
5. SD8987: WSW-19457: Beacon has duplicate IEs in P2P GO mode
6. PCIE9098: WCSWREL-315: Fixed WOWLAN functionality issue
7. PCIE9098: WSW-19638: Added RF_TEST_MODE support
8. SD9098: WCSWREL-314: Fixed Load_Unload failure for the first iteration
9. SD9098: WSW-19638: Added RF_TEST_MODE support
BT/Co-ex Bug Fixes:
-------------------
1. SD8987: WSW-19322: Revert changes done in p41.2 to fix CA2 TCRL2021-2 BQB LMP and BB fail cases
2. SD8987: WSW-20271: Revert changes done in p41.2 to Temporarily disable WARs fixing CSB and sync
3. SD8987: WSW-19977: Hang observed while streaming A2DP music after launching invalid_max_slot exploiter
4. SD8987: WSW-19300: Hang observed after severe A2DP Glitches and audio loss after launching au_rand_flooding exploiter
5. SD8987: WSW-19322: Fix CA2 TCRL2021-2 BQB LMP and BB fail cases
6. SD8987: WSW-20271: Disable WARs fixing CSB and sync train related BQB failures
7. SD8987: WSW-18630: Fixed wifi traffic stuck when running RX and HFP calling
8. SD8987: WSW-17585: New BREDR TCs and failures with TCRL2021-1 and TCRL2021-2
9. SD8987: WSW-19744: DUT is not able to receive any BT RX packets
10. SD8987: WSW-19657: "Invalid HCI Command Parameters" found after enablng the customer-specific batch scan
11. PCIE9098: WSW-17747: Fixed not getting any packet received counts, RSSI, PER information
12. PCIE9098: WSW-17745: Fixed not capturing any packets on IQXeL and Measure tx-power value
13. PCIE9098: WSW-19137: Fixed hang after launching duplicated_encapsulated_payload exploiter
14. PCIE9098: WSW-16828: Fixed AES failing issue even after enabling AES using VSC
15. PCIE9098: WSW-19142: Fixed Pair/Connect issue when exploiter paging_scan_disable is launched
16. PCIE9098: WSW-19145: Fixed HFP Glitches and Connection-timeout after launching invalid_feature_page_execution
17. PCIE9098: WSW-20002: Fixed RX data lost issue for BT RX Throughput transfer
18. PCIE9098: WSW-19523: Fixed deauth on MAC2 resulting in a hang during Coex scenario
19. SD9098: WSW-17747: Fixed not getting any packet received counts, RSSI, PER information
20. SD9098: WSW-17745: Fixed not capturing any packets on IQXeL and Measure tx-power value
21. SD9098: WSW-19137: Fixed hang after launching duplicated_encapsulated_payload exploiter
22. SD9098: WSW-16828: Fixed AES failing issue even after enabling AES using VSC
23. SD9098: WSW-19142: Fixed Pair/Connect issue when exploiter paging_scan_disable is launched
24. SD9098: WSW-19145: Fixed HFP Glitches and Connection-timeout after launching invalid_feature_page_execution
25. SD9098: WSW-20002: Fixed RX data lost issue for BT RX Throughput transfer
26. SD9098: WSW-19523: Fixed deauth on MAC2 resulting in a hang during Coex scenario
27. IW416: WSW-19098: New BREDR TCs and failures with TCRL2021-2, E17535
28. IW416: WSW-19212: Not able to get any packet received counts, RSSI, PER information for BT RX
29. IW416: WSW-19476: Not able to Pair/Connect the REF device when exploiter "paging_scan_disable" is launched
30. IW416: WSW-19474: DUT hang observed after launching "feature_req_ping_pong" exploiter
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Updated firmware:
SDIO-UART W9098 Firmware version 17.68.1.p116
SDIO-UART W8987 Firmware version 16.92.21.p41
SDIO-UART W8801 Firmware version 14.92.36.p174
SDIO-UART IW416 Firmware version 16.92.21.p41
PCIE-UART W9098 Firmware version 17.68.1.p116
SDIO-UART W8997 Firmware version 16.92.21.p41
Unchanged firmware:
PCIE-UART W8997 Firmware version 16.92.21.p26.1
WLAN Bug Fixes:
---------------
1. SD9098: WSW-17876: RF Test Mode: After Disabling cont_mode(CMD18_CW=1), Firmware is getting crashed if radio mode is changed
2. SD9098: WSW-9362: EU-CERT: COT and Channel Access Mechanism tests failing with OptionA Procedure
3. SD8987: WSW-18878: WPA2-PSK Roaming failed
4. SD8987: WSW-18865: VHT80 TCP-tx throughput only run about 170Mbps, both STA and MMH mode
5. SD8987: WSW-16412: Enable 2.4GHz 40MHz bandwidth support for V16 devices
6. SD8987: WSW-18454: Added 802.11k suppor
7. SD8987: WSW-18455: Added 802.11v support
8. SD8987: WSW-18456: Added 802.11r (STA Roaming) support
9. SD8987: WSW-18457: Added 802.11z (Host based TDLS) support
10. SD8987: WSW-18459: DFS (Radar Detection) Master support (some known issues in specific config are found, and under debugging)
11. SD8987: WSW-18461: Per-path regulatory power table (Tested only with RD Board)
12. SD8987: WSW-18462: Per-path DPD Calibration Front-end Loss (Tested only with RD Board)
13. SD8987: WSW-18463: Antenna diversity (Tested only with RD Board)
14. SD8801: WSW-16811: Fix scan cmd timeout issue
15. IW416: WSW-19214: get link layer statistic fail, CMD_RESP: cmd 0x256 error
16. IW416: WSW-16412: Enable 2.4GHz 40MHz bandwidth support for V16 deviceS
17. IW416: WSW-17096: Wi-Fi BGN(2.4Ghz) Association failure issue
18. IW416: WSW-17705: IW416 Wlan Spurious emission issue
19. IW416: WSW-17552: Channel Occupancy Time (COT) failure in STA mode. Max. COT for HT20/MCS0 in 5G mode should be < 6 ms, but observed value is 6.081 ms
20. PCIE9098: WSW-12608: Optimize moal driver loading via firmware init time optimization
21. PCIE9098: WSW-9362: EU-CERT: COT and Channel Access Mechanism tests failing with OptionA Procedure
22. SD8997: WSW-16427: Wi-Fi throughput drops to 0 during scan
23. SD8997: WSW-16819: Wi-Fi occurs 0xa4 command timeout with reason code 12 while playing online video about 16 hours
24. SD8997: WSW-17573: Android UI can't display Wi-Fi standard correctly
BT/Co-ex Bug Fixes:
-------------------
1. SD9098: WSW-17745: RF Test Mode: Not able to capture packets on IQXeL and Measure tx-power value is approx. -42dBm for configured power 4dBm for BLE
2. SD9098: WSW-17747: Not able to get any packet received counts, RSSI, PER information for BT RX
3. SD9098: WSW-18470: Deauthentication on MAC2 and further causing hang issue without ps_mode and auto_ds load parameters
4. SD8987: WSW-18517: 7-8 Glitches are observed during the A2DP SRC streaming + BT Inquiry
5. SD8987: WSW-18598: BT On/Off cycle fails with InBand IR
6. SD8987: Independent Reset via In-band for BT and Wi-Fi(NOTE: This feature needs separate BT Only and WLAN Only firmware binaries, which are provided in this release)
7. IW416: WSW-9978: BLE Qualification protocol failures
8. IW416: WSW-13613: eSCO connection is accepted with retransmission window 0x06
9. IW416: WSW-10265: More than expected channels getting blocked in case of STA + BT Internal AFH
10. PCIE9098: WSW-17745: RF Test Mode: Not able to capture packets on IQXeL and Measure tx-power value is approx. -42dBm for configured power 4dBm for BLE
11. PCIE9098: WSW-17747: Not able to get any packet received counts, RSSI, PER information for BT RX
12. SD8997: WSW-16022: Low 2.4GHz Wi-Fi throughput in Wi-Fi/A2DP Coex case when AP RSSI is weak
13. SD8997: WSW-16243: Hardware Error(0x23) occured during A2DP streaming
14. SD8997: WSW-17570: There is 8s+ delay in waking up OTT host from RCU after host enters into sleep
15. SD8997: WSW-16820: BLE_HID fails to Pair while performing HFP Skype call[Page Timeout: 20sec]
16. SD8997: WSW-18095: Low TP observed in STA(VHT80) WiFi RX Traffic in Coex scenario with INQUIRY/LE_SCAN/A2DP SRC
17. SD8997: WSW-17479: Google Voice Assistant can't be used
18. SD8997: WSW-19097: A2DP glitch in long distance test
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Updated firmware:
SDIO-UART W9098 Firmware version 17.92.1.p98.1
PCIE-UART W8997 Firmware version 16.92.21.p26.1
SDIO-UART W8987 Firmware version 16.92.21.p26
Unchanged firmware:
SDIO-UART W8801 Firmware version 14.92.36.p171
SDIO-UART IW416 Firmware version 16.92.21.p11.2
PCIE-UART W9098 Firmware version 17.92.5.p11
SDIO-UART W8997 Firmware version 16.92.10.p219.5
WLAN Bug Fixes:
---------------
1. SD9098: WSW-17752: [RF-Test Mode]: for "wlan_set_rf_tx_frame"(CMD35), Measured spectrum BW remains 20MHz even when configured BW is 40/80MHz
2. SD9098: WSW-17538: STAUT is not sending SA Query Response to AP's correctly protected SA Query Request
3. SD9098: WSW-17754: "wlan_set_rf_tx_frame"(CMD35), Not able to receive any packets on IQXeL for HE-SU MCS10 & MCS 11 1ss and 2ss data rates
4. SD9098: WSW-18149: Fix for default 2G TxPwrTbl does not show 8dBm for all mod indices
5. SD9098: WSW-14255: DUT goes into hang state during re-association by changing channel/restarting Ex-AP
6. SD9098: WSW-14386: TCP Uplink Traffic on P2P-GO and BSS Start Stop fails after 3hours; Timeout cmd id 0x0
7. SD9098: WSW-11201: Host Wakeup for Management Frames in AP Mode fails, when APUT configured with "mgmtfilter"
8. SD9098: WSW-14213: TCP/UDP Bidirectional traffic test does not sustain more than 3 hours
9. SD9098: WSW-14215: TCP Uplink stress fails with dump within 3hours duration
10. SD9098: WSW-14459: TCP/UDP Bidirectional traffic test does not sustain more than 10mins; cmd53 error is seen
11. SD9098: WSW-14594: uap0 is unable send traffic with all Fixrate LTF+GI combinations
12. SD9098: WSW-15600: Country IE is seen in beacon, even after disabling 80211d option in hostapd file
13. SD9098: WSW-17616: Default tx-power values (8dBm) are changing to some random values for different rate ID’s after starting hostapd
14. PCIE8997: WSW-16427: Fixed issue of Wi-Fi throughput drops to 0 during scan
15. PCIE8997: WSW-16819: Fixed issue of 0xa4 command timeout with reason code 12 while playing online video about 16 hours
16. PCIE8997: WSW-17568: Fixed issue of "Ext scan enh timeout" occurs after connect to IPv6 network for a long time
17. PCIE8997: WSW-17573: Fixed issue of Android UI not displaying Wi-Fi standard correctl
18. PCIE8997: WSW-17613: 0x107 command timeout occurs while playing online video based on IPv6 network for a long time
19. PCIE8997: WSW-17657: In-STA auto disconnects from Ex-AP in standby and is unable to reconnect Ex-AP
20. SD8987: WSW-17426: rf test mode: 5G Tx EVM/SPECTRUM MASK failed on CH64 and CH100 with mass market release
21: SD8987: WSW-17577: RF test mode bandwidth 40MHz not working with 2.4G band
22. SD8987: WSFD-386: FW and VHAL Implementation for WOWLAN
23. SD8987: WSW-15035: Fixed WiFi scan event timeout happen during run WiFi scan and BT connect-disconnect cycle test simultaneously sometimes
24. SD8987: WSW-16212: Fixed fw init fail with 0xf007 when independent reset and STA keep connection
25. SD8987: WSW-17450: Fixed the issue of android.net.wifi.cts.WifiManagerTest failure
BT/Co-ex Bug Fixes:
-------------
1. SD9098: WSW-17662: Fixed the issue of Link Loss(Connection Timeout) during LE Connectio
2. SD9098: WSW-17667: Wlan Deauthentication is observed with A2DP Source + STA[HT20] with DUT ACL Role both Slave and Master
3. SD9098: WSW-17619: Authentication Failure is observed when try to connect with DUT after Power on/off
4. SD9098: WSW-17887: During encryption process if host send remote version request, sometimes link is getting disconnected with LMP/LL timeout
5. SD9098: WSW-17982: After making call, Synchronous Connect Complete returns with status Unsupported LMP Parameter Value / Unsupported LL Parameter Value (0x20)
6. SD9098: WSW-17249: Random DUT hang observed after receiving directed advertisements while doing le scan
7. SD9098: WSW-16606: Low BT Tx/Rx/Bi-Directional TP on BT(M/S) for 1/3/5 Slot packet type
8. SD9098: WSW-13135: Throughput Drops abruptly in OPP_Tx to 8/16KBps from 64KBps when OPP_Tx is operating and simultaneously TCP_RX is running
9. PCIE8997: WSW-17982: After making call, Synchronous Connect Complete returns with status Unsupported LMP Parameter Value / Unsupported LL Parameter Value (0x20)
10. PCIE8997: WSW-17383: Request to enable Multi ADV feature to pass GTV Certification
11. PCIE8997: WSW-17479: Fixed issue of Google Voice Assistant usage
12. PCIE8997: WSW-17570: Fixed issue of 8s+ delay in waking up OTT host from RCU after host enters into sleep
13. PCIE8997: WSW-16306: Fixed issue of Low BT Tx/Rx throughput observed for all packet types in shielded environment
14. PCIE8997: WSW-18095: Fixed issue of Low TP observed in STA(VHT80) WiFi RX Traffic in Coex scenario with INQUIRY/LE_SCAN/A2DP SRC
15. SD8987: WSW-16820: BLE_HID fails to Pair while performing HFP Skype call
16. SD8987: WSW-16922: PTS Flouride Certification got failure for HSP/AG/IAC/BV-01-I
17. SD8987: WSW-16422: Set Random Private Address Timeout Command is accepting values more than 1 Hr
18. SD8987: WSW-16780: Bad and distorted voice quality can be heard from remote phone if we do connect and disconnect test with headset no matter incoming or outgoing call
19. SD8987: WSW-16924: Ctlr H/w error event showed when connect with Pixel Buds Version2
20. SD8987: WSW-15505: Heavy A2DP glitches can be heard in the noisy ENV if take speaker ~10meter away from UUT
21. SD8987: WSW-17237: LE_APCF_Command received from BT stack, 8987 return as dis-allowed
22. SD8987: WSW-16266: BLE devices failed to be connected during BT activities like HFP active call
23. SD8987: WSW-17034: No BT inquiry result found during PS4 gamepad pair/unpair test with A2DP streaming and BLE RC connected
24. SD8987: WSW-17423: Voice not hearable from both headset and phone sides when make the HFP call with NBS mode
25. SD8987: WSW-17476: Random A2DP glitches can be heard during A2DP playing with PixelBuds headset in the Noisy ENV
26. SD8987: WSW-16170: Read By Group Type Response is not being sent by the DUT due to collision between Public key request
27. SD8987: WSW-16438: WiFi hang up with command timeout(0x24) during running BT OOB IR or A2DP stress test and wifi do activity
28. SD8987: WSW-15570: A2DP glitch with wifi connected and do scan or Traffic running in noisy when testing A2DP+STA and A2DP+BLE RC+STA
29. SD8987: WSW-17664: BLE Fast Pair Doesnt Work as per expectation
30. SD8987: WSW-17325: DUT does not respond to POLL packets send by Remote Device due to which Connection terminates with "Connection timeout"
31. SD8987: WSW-17256: LE Create Connection with use white list for 2nd link is connected with wrong BD address
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Firmware:
SDIO-UART W8801 Firmware version 14.92.36.p171
SDIO-UART IW416 Firmware version 16.92.21.p11.2
PCIE-UART W9098 Firmware version 17.92.5.p11
SDIO-UART W8997 Firmware version 16.92.10.p219.5
PCIE-UART W8997 Firmware version 16.92.21.p17
SDIO-UART W8987 Firmware version 16.92.21.p11.1
SDIO-UART W9098 Firmware version 17.92.1.p91
WLAN Bug Fixes:
---------------
1. SD9098: New Release
2. PCIE8997: WSW-13725 COT and Channel Access Mechanism tests need to pass with OptionA Procedure
3. PCIE8997: WSW-16784 Fix data path stuck issue in WMM disabled case
4. PCIE8997: WSW-15054 Fix 5G fail to start when sae_pwe=1 issue
5. PCIE8997: WSFD-386 FW and VHAL Implementation for WOWLAN
6. PCIE8997: WSW-11784 STAUT sends more than 1 MPDU in AMPDU even though tx win restricted to 1, with SCBT AP
7. PCIE8997: WSW-16378 Scan event timeout with 0x20 cmd timeout, when run connect extAP with different security overnight stress
8. PCIE8997: WSW-16296 STAUT is responding to the ARP requests after receiving encrypted M3 and reset PN from AP
9. PCIE8997: WSW-16620 wlan_wakeup_card_timeout_func: ps_state=3 when run WiFi activities from GUI along with BT activitie
10. PCIE8997: WSW-16270 Enable DFS parameter to detect RADAR
11. PCIE8997: WSW-16602 FW timeout when switch conect with 2 AP with driver debug log enable
12. PCIE8997: WSW-16417 0x107/0x10d command timeout when switching AP security between WPA-PSK and open
13. PCIE8997: WSW-16207 0x10d command timeout when switching AP Security between open and WPA2-PSK
14. PCIE8997: WSW-12415 "Authentication Failure" happens during pair use AES method
15. PCIE8997: WSW-16126 Disable Aggr for MCS datarates < 30Mbps
16. PCIE8997: WSW-7275 Sometimes Ex-STA fails to get DHCP during conenct/disconnect loop
17. PCIE8997: WSW-13477 Fix chanAttrTbl chan num issue
18. PCIE8997: WSW-14259 Fix AMSDU size report issue in uAP mode
19. PCIE8997: WSW-11977 [11AC][TC-4.2.20]-Mismatch in WMMIE Parameter count observed in beacon and association response when configured as APUT
20. PCIE8997: WSW-13487 [HT40 HT Forty MHz Intolerant is set makes Throughput low in uAP mode]
21. PCIE8997: WSW-12207 Fix the issue that DUT follows AP's advertised Power Constraint
22. PCIE8997: WSW-15390 [RB3, RB3+, KF2][FP92] Re-enable 2G 40MHz support
BT/Co-ex Bug Fixes:
-------------
1. SD9098: New Release
2. PCIE8997: WSW-17423 Voice not hearable from both headset and phone sides when make the HFP call with NBS mode.Fail rate 100%
3. PCIE8997: WSW-16266 BLE HID devices failed to be connected during BT activities, Fail rate:70%
4. PCIE8997: WSW-16869 Observed DUT hang issue with two eSCO links
5. PCIE8997: WSW-16243 Hardware Error(0x23) occured during A2DP streaming
6. PCIE8997: WSW-13676 A2DP_SRC Streaming got suspended automatically with Hardware Error when BT Inquiry was running in the Background
7. PCIE8997: WSW-13965 [KF2][IMX8M.Linux][P2P-GC_BGN-20]Low WLAN TP is observed during A2DP_SRC
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Firmware:
SDIO-UART W8801 Firmware version 14.92.36.p171
SDIO-UART IW416 Firmware version 16.92.21.p11.2
PCIE-UART W9098 Firmware version 17.92.5.p11
SDIO-UART W8997 Firmware version 16.92.10.p219.5
PCIE-UART W8997 Firmware version 16.92.10.p213.4
SDIO-UART W8987 Firmware version 16.92.21.p11.1
WLAN Bug Fixes:
---------------
1. PCIE8997: Fixed issue with 5G start when sae_pwe=1 is set
2. PCIE8997: Added WPA3 R3 Support
3. PCIE9098: Fixed issue with 5G start when sae_pwe=1 is set
4. PCIE9098: Added WPA3 R3 Support
5. SD8801: Fixed issue with 5G start when sae_pwe=1 is set
6. SD8801: Added WPA3 R3 Support
7. SD8987: Fixed issue with 5G start when sae_pwe=1 is set
8. SD8987: Addressed Ideal period probability cert test failure in MMH 5GHz HT20 mode
9. SD8987: Added FW and VHAL implementation for WoWLAN
10. SD8987: Added WPA3 R3 Support
11. SD8997: Fixed issue with 5G start when sae_pwe=1 is set
12. SD8997: Added WPA3 R3 Support
13. SDIW416: Fixed issue with 5G start when sae_pwe=1 is set
14. SDIW416: Addressed Ideal period probability cert test failure in MMH 5GHz HT20 mode
15. SDIW416: Added WPA3 R3 Support
BT Bug Fixes:
-------------
1. PCIE8997: Added an update to the 'Impersonation in the Passkey Entry Protocol' Vulnerability (original CVE-2020-26558)
2. PCIE8997: Added BT ANSSI VU fix
3. PCIE9098: Added an update to the 'Impersonation in the Passkey Entry Protocol' Vulnerability (original CVE-2020-26558)
4. PCIE9098: Added BT ANSSI VU fix
5. SD8987: Added an update to the 'Impersonation in the Passkey Entry Protocol' Vulnerability (original CVE-2020-26558)
6. SD8987: Fixed issue of Set Random Private Address Timeout Command accepting values more than 1 Hr
7. SD8987: Added BT ANSSI VU fix
8. SD8997: Added an update to the 'Impersonation in the Passkey Entry Protocol' Vulnerability (original CVE-2020-26558)
9. SD8997: Added BT ANSSI VU fix
10. SDIW416: Added an update to the 'Impersonation in the Passkey Entry Protocol' Vulnerability (original CVE-2020-26558)
11. SDIW416: Fixed issue of Set Random Private Address Timeout Command accepting values more than 1 Hr
12. SDIW416: Added BT ANSSI VU fix
13. SDIW416: More than expected channels getting blocked in case of STA + BT internal AFH
Yocto build, it requires to copy the files to:
- lib/firmware/nxp/
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
from BSP conf
FwImage: update firmware to mxm5x17283
FwImage: wifi_mod_para.conf: change the load parameters of wifi
driver to support WPA3 feature
also refine load params to better align with WCS team.
Still keep wfd_name=p2p and max_vir_bss=1 to better support p2p
function.
Also add SD8801 load parameters support.
Signed-off-by: yang.tian <yang.tian@nxp.com>
As WCS team suggested, to keep align with them, need to remove the
wfd_name setting.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Approved-by: Tian Yang <yang.tian@nxp.com>
Firmware:
SDIO-UART W8801 Firmware version 14.92.36.p170
SDIO-UART IW416 Firmware version 16.92.21.p11
PCIE-UART W9098 Firmware version 17.92.5.p10
SDIO-UART W8997 Firmware version 16.92.10.p219.4
PCIE-UART W8997 Firmware version 16.92.10.p213.3
SDIO-UART W8987 Firmware version 16.92.21.p11
WLAN Bug Fixes:
---------------
1. PCIE8997: Fixed pre-cert issue where STA is responding to the ARP requests after receiving encrypted M3 and reset PN from AP
2. PCIE8997: Added WFA SVD failure fixes
3. PCIE9098: Fixed pre-cert issue where STA is responding to the ARP requests after receiving encrypted M3 and reset PN from AP
4. PCIE9098: Added WFA SVD failure fixes
5. SD8801: Fixed low TCP RX throughput issue For Linksys 1900AC AP
6. SD8801: Corresponding firmware change for fixing low throughput issue in WPA3-SAE security
7. SD8801: Enabled ED-MAC by default
8. SD8801: Fixed low throughput in Rx A-MSDU
9. SD8801: Fixed low throughput issue in P2P GC
10. SD8801: Added WFA SVD failure fixes
11. SD8987: Added WFA SVD failure fixes
12. SD8987: Minor generic bug fixe
13. SD8987: Fixed RF test mode "Continuous Transmit Test" error happened on the second time test
14. SD8987: Fixed Low TCP-Tx and UDP-Tx throughput issues
15. SD8997: Fixed pre-cert issue where STA is responding to the ARP requests after receiving encrypted M3 and reset PN from AP
16. SD8997: Added WFA SVD failure fixes
17. SDIW416: Added WFA SVD failure fixes
18. SDIW416: Minor generic bug fixes
BT Bug Fixes:
-------------
1. SD8987: Minor generic bug fixe
2. SD8987: Fixed FW replying with different reason when the Host has rejected the incoming call
3. SD8987: Fixed Outgoing connection disconnection with reason "Connection terminated by local host" after pairing with reference device
4. SDIW416: Fixed an issue with retransmission window during eSCO connection accept
5. SDIW416: Continuous A2DP-SNK audio glitches issue observed in MMH Rx traffic
Yocto build, it requires to copy the files to:
- lib/firmware/nxp/
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Change the wifi driver load parameters to support WPA3 feature, also to
better align with WCS team.
Still keep wfd_name=p2p and max_vir_bss=1 to better support p2p function.
Also add SD8801 load parameters support.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Approved-by: Tian Yang <yang.tian@nxp.com>
Firmware:
SDIO-UART IW416 Firmware version 16.92.10.p233.2
PCIE-UART W9098 Firmware version 17.92.5.p9
SDIO-UART W8997 Firmware version 16.92.10.p219.2
PCIE-UART W8997 Firmware version 16.92.10.p213.2
SDIO-UART W8987 Firmware version 16.92.10.p210.1
WLAN Bug Fixes:
---------------
1. IW416: Fixed the issue of Channel Occupancy Time (COT) coming as 7.85 msec where as it should be under 6 msec
2. SDIO8997: Fixed issue of ping through gateway for some minutes when running long time test
3. SDIO8997: Added 2.4GHz 40MHz bandwidth support for V16 devices
4. PCIE8997: Fixed issue of ping through gateway for some minutes when running long time test
5. PCIE8997: Added 2.4GHz 40MHz bandwidth support for V16 devices
BT Bug Fixes:
-------------
1. IW416: Fixed the issue of DUT blocking more than 50/55 channels in shielded environment without any external noise
2. IW416: Fixed the issue of Continuous A2DP-SNK audio glitches in Rx traffic
3. PCIE9098: Fixed the scan on fail as Command Disallowed is observed for LE Set Extended Scan Parameters
4. SDIO8997: Hardware Error(0x23) occured during A2DP streaming
5. PCIE8997: Hardware Error(0x23) occured during A2DP streaming
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Firmware:
SDIO-UART IW416 Firmware version 16.92.10.p233.1
PCIE-UART W9098 Firmware version 17.92.5.p8
SDIO-UART W8997 Firmware version 16.92.10.p219.1
PCIE-UART W8997 Firmware version 16.92.10.p213.1
SDIO-UART W8987 Firmware version 16.92.10.p210.1
WLAN Bug Fixes:
---------------
1. IW416: [WCSWREL-100] L5.4.70: 2.4G AP connect fail after run 5G STA mode
2. IW416: Fixed BSS start/stop stress test failed with 0x10d cmd timeout
3. PCIE9098: Continuous association with 5 different APs stress fails
4. PCIE9098: DUT is unable to receive packets in MFG mode
5. PCIE9098: Command timeout 0x107 observed while running Tx UDP traffic to two stations with scan triggered for every 30s in background
6. SDIO8997: [WCSWREL-100] L5.4.70: 2.4G AP connect fail after run 5G STA mode
7. PCIE8997: [WCSWREL-100] L5.4.70: 2.4G AP connect fail after run 5G STA mode
8. SDIO8987: [WCSWREL-100] L5.4.70: 2.4G AP connect fail after run 5G STA mode
BT Bug Fixes:
-------------
1. IW416: Command tx timeout as soon as advertise on/off is done in a loop
2. IW416: Fixed the error "connection rejected due to security reasons" during lescan and file transfer
3. IW416: Fixed the Type1XK_Adaptivity failure
4. IW416: Fixed the LE link disconnection with "Connection Timeout"
5. IW416: Fixed the “Authentication Failure” issue found during BT E0/AES connection process
6. IW416: [WCSWREL-136]cannot hear voice from BT HFP call with IW416 on both imx8mq and imx8mp
7. IW416: Disable AES feature support due to known issue
8. PCIE9098: Disabled LE Extended ADV, periodic ADV & Channel Selection Algorithm
9. PCIE9098: Disable AES feature support due to known issue
10. SDIO8997: Fixed the low 2.4GHz Wi-Fi throughput in Wi-Fi/A2DP Coex case when AP RSSI is weak
11. SDIO8997: Fixed the Low TP ~400Kbps issue during STA_2.4GHz_A2DP_SRC/SNK_UDP_RX
12. SDIO8997: Disable AES feature support due to known issue
13. PCIE8997: Disable AES feature support due to known issue
14. SDIO8987: Fixed the Issue of Controller not sending "LE create connection" command into air
15. SDIO8987: [WCSWREL-147] Bluetooth will crash and restart fail in stress test
16. SDIO8987: Disable AES feature support due to known issue
Yocto build, it requires to copy the files to:
- lib/firmware/nxp/
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Update Android wifi_mod_para.conf to
add SD9098 and SD8978 module wifi config,
and also update SD8997 and PCIE9098 wifi
module config.
Signed-off-by: yang.tian <yang.tian@nxp.com>
Firmware:
SDIO-UART IW416 Firmware version 16.92.10.p177
PCIE-UART W9098 Firmware version 17.92.5.p6
SDIO-UART W8997 Firmware version 16.92.10.p219
PCIE-UART W8997 Firmware version 16.92.10.p213
SDIO-UART W8987 Firmware version 16.92.10.p210
WLAN Bug Fixes:
---------------
1. PCIE9098: TCP Uplink Traffic Test on P2P-GO and BSS Start Stop stress fails within 1hour
2. PCIE9098: Suspend-Resume fails in connected state
3. PCIE9098: ED-Mac is not enabled by default
4. PCIE9098: EU-Cert is getting failed for 2.4G in mlan0 interface in STA mode
BT Bug Fixes:
-------------
1. SDIO8997: Low TP ~30Kbps is observed during [STA_2.4GHZ_A2DP_SRC/SNK_TCP_TX]
Yocto build, it requires to copy the files to:
- lib/firmware/nxp/
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Firmware:
PCIE-UART W9098 Firmware version 17.92.5.p1
SDIO-UART W8997 Firmware version 16.92.10.p216
PCIE-UART W8997 Firmware version 16.92.10.p212
SDIO-UART W8987 Firmware version 16.92.10.p209
WLAN Bug Fixes:
---------------
1. PCIE9098: Fixed issues seen during stress test with data traffic.
BT Bug Fixes:
-------------
None.
Yocto build, it requires to copy the files to:
- lib/firmware/nxp/
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Firmware:
PCIE-UART W9098 Firmware version 17.92.1.p55
SDIO-UART W8997 Firmware version 16.92.10.p156
PCIE-UART W8997 Firmware version 16.92.10.p212
SDIO-UART W8987 Firmware version 16.92.10.p209
WLAN Bug Fixes:
---------------
1. Added Wi-Fi VU fixes for four firmwares
2. PCIE9098: Fixed 11AX pre-cert/EU-cert test issues
3. PCIE9098: Fixed DFS channel switch compliance related issue
4. PCIE9098: Fixed WPA3 band switch issue
5. PCIE9098: Fixed issues related to scan stress
6. PCIE9098: Fixed issues seen during traffic stress test
7. SDIO8997: Fixed issues seen during traffic stress test
BT Bug Fixes:
-------------
1. PCIE9098: Fixed various issues related to device hang
2. PCIE9098: Fixed issues with BT mode switch
Yocto build, it requires to copy the files to:
- lib/firmware/nxp/
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Firmware:
PCIE-UART W8997 Firmware version 16.92.10.p211
PCIE-UART W9098 Firmware version 17.92.1.p46
SDIO-UART W8997 Firmware version 16.92.10.p150
WLAN Bug Fixes:
---------------
1. Fixed an issue where wakeup card timeout is seen when STAUT connects
to Ext-AP
2. Added multiple fixes for 11ax pre-cert issues
3. Added RF Test Mode support
4. Added fixes for scan command timeout seen during stress tests
5. Added fixes for 11ac pre-cert failures
BT Bug Fixes:
-------------
1. Fixed an issue where BT restart is observed
2. Fixed issues where A2DP gliches are observed when connecting a
second phone
3. Ported multiple BT fixes for stability
Yocto build, it requires to copy the files to:
- lib/firmware/nxp/
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Add file wifi_mod_para_powersave.conf which include
powersave_enable flag. Add logic in wifi driver which
can parse this flag.
Add append_bootargs:
setenv append_bootargs moal.mod_para=wifi_mod_para_powersave.conf
saveenv
Change-Id: If0875510385219e47f9b74c4b64b11701849db6c
Signed-off-by: zhipeng.wang <zhipeng.wang_1@nxp.com>
Firmware:
PCIE-UART W8997 Firmware version 16.92.10.p126
WLAN Bug Fixes:
---------------
1. Fix uAP start issue on switching bands
2. Fixed WLAN Link loss during UDP Rx + BT Inquiry, and WLAN deauth
during BT HFP coex scenarios
BT Bug Fixes:
-------------
1. Added fix to handle processing of SSR command to unblock command
queuing which was causing BT restart
Yocto build, it requires to copy the files to:
- lib/firmware/nxp/
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Firmware:
PCIE-UART W8997 Firmware version 16.92.10.p118
WLAN Bug Fixes:
---------------
1. Fixed VHT compressed beamforming frame related pre-cert issues
2. Corresponding firmware change for fixing WPA3 SAE pre-cert requirement
3. Fixed issue with scan logic where firmware was aborting complete scan
even if noise is detected on a different channel
4. Updated scan gap logic to prevent the DUT from missing ECSA IE beacons
5. Test Mode fix: Fixed path B Tx power issue for continuous wave mode
BT Bug Fixes:
-------------
1. Added fixes for A2DP glitches in various scnearios
2. Added change of disabling ping as AES is disabled.
This was causing LMP response timeout issue
3. Added changes to correctly handle WAR flag name to enable fix for
negative test cases involving LE connection.
Coex Bug Fixes:
-------------
1. Added fix for A2DP Glitches during coex scenarious
2. Added fix for BLE HID links losses
3. Added WLAN throughput improvements during BT device discovery scenarious
Yocto build, it requires to copy the files to:
- lib/firmware/nxp/
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Firmware:
PCIE-UART W8997 Firmware version 16.92.10.p113
Yocto build, it requires to copy the files to:
- lib/firmware/nxp/
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
