mirror of
https://github.com/nxp-imx/mwifiex.git
synced 2024-05-14 00:59:21 +00:00
33d9f8e4f3
Add initial MxM (multi-chip-multi-interface) wifi driver. The driver target is to support 88w8987/88w8997/88w9098, currently it only supports 88w8987. The MxM wifi driver is merged from below repo and applied some patches for block and build issues. ssh://git@bitbucket.sw.nxp.com/wcswrel/ rel-nxp-wifi-fp92-bt-fp85-linux-android-mxm4x17169-gpl.git The sdk only includes application, the driver already is merged into linux kernel. Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
1126 lines
46 KiB
Plaintext
1126 lines
46 KiB
Plaintext
===============================================================================
|
|
U S E R M A N U A L
|
|
|
|
Copyright 2014-2020 NXP
|
|
|
|
|
|
1) FOR DRIVER BUILD
|
|
|
|
Goto source code directory wlan_src/.
|
|
make [clean] build
|
|
The driver and utility binaries can be found in ../bin_xxxx directory.
|
|
The driver code supports Linux kernel from 2.6.32 to 5.5.2.
|
|
|
|
2) FOR DRIVER INSTALL
|
|
|
|
a) Copy firmware image to /lib/firmware/nxp/, copy wifi_mod_para.conf to /lib/firmware/nxp/.
|
|
b) Install WLAN driver
|
|
There are drv_mode, max_sta_bss, max_uap_bss etc. module parameters.
|
|
The bit settings of drv_mode are,
|
|
Bit 0 : STA
|
|
Bit 1 : uAP
|
|
Bit 2 : WIFIDIRECT
|
|
|
|
max_sta_bss: Maximum number of STA BSS (default 1, max 1)
|
|
sta_name: Name of the STA interface (default: "mlan")
|
|
max_uap_bss: Maximum number of uAP BSS (default 1, max 1)
|
|
uap_name: Name of the uAP interface (default: "uap")
|
|
uap_max_sta: Maximum number of STA for UAP/GO (default 0, max 64)
|
|
max_wfd_bss: Maximum number of WIFIDIRECT BSS (default 1, max 1)
|
|
wfd_name: Name of the WIFIDIRECT interface (default: "wfd")
|
|
max_vir_bss: Number of Virtual interfaces (default 0)
|
|
uap_oper_ctrl: uAP operation control when in-STA disconnect with ext-AP
|
|
0: default do nothing, 2: uAP stops and restarts automatically
|
|
For example, to install multi-chip driver,
|
|
insmod mlan.ko
|
|
insmod moal.ko mod_para=nxp/wifi_mod_para.conf [drvdbg=0x7]
|
|
wifi_mod_para.conf is used to support multi-chips which has different load module parameters. It contains
|
|
the module parameters for different chips.
|
|
c) Uninstall WLAN driver,
|
|
ifconfig mlanX down
|
|
ifconfig uapX down
|
|
rmmod moal
|
|
rmmod mlan
|
|
|
|
To load driver with MFG firmware file, use mfg_mode=1 when insmod WLAN driver and
|
|
specify MFG firmware name if needed.
|
|
|
|
There are some other parameters for debugging purpose etc. Use modinfo to check details.
|
|
drvdbg=<bit mask of driver debug message control>
|
|
dev_cap_mask=<Bit mask of the device capability>
|
|
mac_addr=xx:xx:xx:xx:xx:xx <override the MAC address (in hex)>
|
|
auto_ds=0|1|2 <use MLAN default | enable auto deepsleep | disable auto deepsleep>
|
|
ps_mode=0|1|2 <use MLAN default | enable IEEE PS mode | disable IEEE PS mode>
|
|
max_tx_buf=2048|4096|8192 <maximum AMSDU Tx buffer size>
|
|
pm_keep_power=1|0 <PM keep power in suspend (default) | PM no power in suspend>
|
|
shutdown_hs=1|0 <Enable HS when shutdown | No HS when shutdown (default)>
|
|
cfg_11d=0|1|2 <use MLAN default | enable 11d | disable 11d>
|
|
dts_enable=0|1 <Disable DTS | Enable DTS (default)>
|
|
fw_name = <FW file name>
|
|
e.g. copy pcieuart9098_combo_v1.bin to firmware directory, fw_name=nxp/pcieuart9098_combo_v1.bin
|
|
fw_region <Enable create channel regulatory domain from FW (default) | disable create channel regulatory domain from FW>
|
|
hw_test=0|1 <Disable hardware test (default) | Enable hardware test>
|
|
fw_serial=0|1 <support parallel download FW | support serial download FW (default)>
|
|
req_fw_nowait=0|1 <use request_firmware API (default) | use request_firmware_nowait API>
|
|
antcfg=0|1|2|0xffff <default | Tx/Rx antenna 1 | Tx/Rx antenna 2 | enable antenna diversity>
|
|
slew_rate: Slew Rate Control value = 0|1|2|3 (0 is the slowest slew rate and 03 has the highest slew rate (default))
|
|
init_cfg=<init config (MAC addresses, registers etc.) file name>
|
|
e.g. copy init_cfg.conf to firmware directory, init_cfg=nxp/init_cfg.conf
|
|
cal_data_cfg=<CAL data config file name>
|
|
e.g. copy cal_data.conf to firmware directory, cal_data_cfg=nxp/cal_data.conf
|
|
dpd_data_cfg=<DPD data config file name>
|
|
e.g. copy dpd_data.conf to firmware directory, dpd_data_cfg=nxp/dpd_data.conf
|
|
txpwrlimit_cfg=<Tx power limit config file name>
|
|
e.g. copy txpwrlimit_cfg_set.conf to firmware directory, txpwrlimit_cfg=nxp/txpwrlimit_cfg_set.conf
|
|
cntry_txpwr=<Enable setting tx power table of country | Disable setting tx power table of country (default)>
|
|
init_hostcmd_cfg=<init hostcmd config file name>
|
|
e.g. copy init_hostcmd_cfg.conf to firmware directory, init_hostcmd_cfg=nxp/init_hostcmd_cfg.conf
|
|
sdio_rx_aggr=1|0 <Enable SDIO rx aggr (default) | Disable SDIO rx aggr>
|
|
cfg80211_wext=<bit mask of CFG80211 and WEXT control>
|
|
Bit 0: STA WEXT
|
|
Bit 1: uAP WEXT
|
|
Bit 2: STA CFG80211
|
|
Bit 3: uAP CFG80211
|
|
reg_alpha2=<Regulatory alpha2 (default NULL)>
|
|
skip_fwdnld=0|1 <enable FW download support (default) | disable FW download support>
|
|
wq_sched_prio: Priority for work queue
|
|
wq_sched_policy: Scheduling policy for work queue
|
|
(0: SCHED_NORMAL, 1: SCHED_FIFO, 2: SCHED_RR, 3: SCHED_BATCH, 5: SCHED_IDLE)
|
|
Please note that, both wq_sched_prio and wq_sched_policy should be provided
|
|
as module parameters. If wq_sched_policy is (0, 3 or 5), then wq_sched_prio
|
|
must be 0. wq_sched_prio should be 1 to 99 otherwise.
|
|
rx_work=0|1|2 <default | Enable rx_work_queue | Disable rx_work_queue>
|
|
pcie_int_mode=0|1|2 <Legacy mode, MSI mode (default), MSI-X mode>
|
|
pcie_int_mode=0|1 <Legacy mode, MSI mode (default)>
|
|
wakelock_timeout=<set wakelock_timeout value (ms)>
|
|
defined(SD9098)||defined(USB9098) || defined(PCIE9098) || defined(SD9097) || defined(USB9097)|| defined(PCIE9097)||defined(SD8978)
|
|
pmic=0|1 <No pmic configure cmd sent to firmware | Send pmic configure cmd to firmware>
|
|
indication_gpio=0xXY <GPIO to indicate wakeup source and its level; high four bits X:
|
|
level(0/1) for normal wakeup; low four bits Y: GPIO pin number. This parameter
|
|
only works with specific board and firmware.>
|
|
hs_wake_interval=<Host sleep wakeup interval,it will round to nearest multiple dtim*beacon_period in fw>
|
|
disconnect_on_suspend=0|1 <Disable disconnect wifi on suspend (default) | Enable disconnect wifi on suspend>
|
|
hs_mimo_switch=0|1 <Disable dynamic MIMO-SISO switch during host sleep (default) | Enable dynamic MIMO-SISO switch during host sleep>
|
|
usb_aggr=0|1|2 <use MLAN default (disabled) | enable USB aggr | disable USB aggr>
|
|
low_power_mode_enable=0|1 <disable low power mode (default)| enable low power mode>
|
|
When low power mode is enabled, the output power will be clipped at ~+10dBm and the
|
|
expected PA current is expected to be in the 80-90 mA range for b/g/n modes
|
|
indrstcfg=<2-byte IR configuration>
|
|
gpio pin (high byte): GPIO pin no to be used as trigger for out band reset
|
|
(0xFF: default pin configuration)
|
|
ir_mode (low byte) : independent reset mode
|
|
(0: disable, 1: enable out band, 2: enable in band)
|
|
For example, to enable out band reset via gpio_pin 14
|
|
indrstcfg=0x0e01
|
|
To enable out band reset via default gpio_pin
|
|
indrstcfg=0xff01
|
|
To enable in band reset and disable out band reset
|
|
indrstcfg=0x02
|
|
fixed_beacon_buffer=0|1 <allocate default buffer size (default) | allocate max buffer size>
|
|
GoAgeoutTime=0|x <use default ageout time (default) | set Go age out time xTU(TU 100ms)>
|
|
multi_dtim=0|x <use default DTIM interval (default) | set x*beacon_period as DTIM interval>
|
|
inact_tmo=0|x <use default IEEE ps inactivity timout value (default) | use IEEE ps inactivity timeout value x ms>
|
|
host_mlme=0|1 <Disable Host MLME support (default)| Enable Host MLME support>
|
|
country_ie_ignore=0|1 <Follow countryIE from AP and beacon hint enable (default) | Ignore countryIE from AP and beacon hint disable>
|
|
beacon_hints=0|1 <enable beacon hints(default) | disable beacon hints>
|
|
|
|
Note: On some platforms (e.g. PXA910/920) double quotation marks ("") need to used
|
|
for module parameters.
|
|
insmod sdxxx.ko "<para1> <para2> ..."
|
|
|
|
3) FOR DRIVER PROC & DEBUG
|
|
|
|
The following info are provided in /proc/net/mwlan/adapterX/mlanY/info,
|
|
on kernel 2.6.24 or later, the entry is /proc/mwlan/adapterX/mlanY/info.
|
|
|
|
driver_name = "wlan"
|
|
driver_version = <chip id, firmware version and driver version>
|
|
interface_name = "mlanX"
|
|
bss_mode = "Ad-hoc" | "Managed" | "Auto" | "Unknown"
|
|
media_state = "Disconnected" | "Connected"
|
|
mac_address = <6-byte adapter MAC address>
|
|
multicase_count = <multicast address count>
|
|
essid = <current SSID>
|
|
bssid = <current BSSID>
|
|
channel = <current channel>
|
|
region_code = <current region code>
|
|
multicast_address[n] = <multicast address>
|
|
num_tx_bytes = <number of bytes sent to device>
|
|
num_rx_bytes = <number of bytes received from device and sent to kernel>
|
|
num_tx_pkts = <number of packets sent to device>
|
|
num_rx_pkts = <number of packets received from device and sent to kernel>
|
|
num_tx_pkts_dropped = <number of Tx packets dropped by driver>
|
|
num_rx_pkts_dropped = <number of Rx packets dropped by driver>
|
|
num_tx_pkts_err = <number of Tx packets failed to send to device>
|
|
num_rx_pkts_err = <number of Rx packets failed to receive from device>
|
|
carrier "on" | "off"
|
|
tx queue "stopped" | "started"
|
|
|
|
The following debug info are provided in /proc/net/mwlan/adapterX/mlanY/debug,
|
|
on kernel 2.6.24 or later, the entry is /proc/mwlan/adapterX/mlanY/debug.
|
|
|
|
drvdbg = <bit mask of driver debug message control>
|
|
wmm_ac_vo = <number of packets sent to device from WMM AcVo queue>
|
|
wmm_ac_vi = <number of packets sent to device from WMM AcVi queue>
|
|
wmm_ac_be = <number of packets sent to device from WMM AcBE queue>
|
|
wmm_ac_bk = <number of packets sent to device from WMM AcBK queue>
|
|
max_tx_buf_size = <maximum Tx buffer size>
|
|
tx_buf_size = <current Tx buffer size>
|
|
curr_tx_buf_size = <current Tx buffer size in FW>
|
|
ps_mode = <0/1, CAM mode/PS mode>
|
|
ps_state = <0/1/2/3, awake state/pre-sleep state/sleep-confirm state/sleep state>
|
|
is_deep_sleep = <0/1, not deep sleep state/deep sleep state>
|
|
wakeup_dev_req = <0/1, wakeup device not required/required>
|
|
wakeup_tries = <wakeup device count, cleared when device awake>
|
|
hs_configured = <0/1, host sleep not configured/configured>
|
|
hs_activated = <0/1, extended host sleep not activated/activated>
|
|
tx_pkts_queued = <number of Tx packets queued>
|
|
pps_uapsd_mode = <0/1, PPS/UAPSD mode disabled/enabled>
|
|
sleep_pd = <sleep period in milliseconds>
|
|
qos_cfg = <WMM QoS info>
|
|
tx_lock_flag = <0/1, Tx lock flag>
|
|
port_open = <0/1, port open flag>
|
|
scan_processing = <0/1, scan processing flag>
|
|
num_tx_timeout = <number of Tx timeout>
|
|
num_cmd_timeout = <number of timeout commands>
|
|
timeout_cmd_id = <command id of the last timeout command>
|
|
timeout_cmd_act = <command action of the last timeout command>
|
|
last_cmd_id = <command id of the last several commands sent to device>
|
|
last_cmd_act = <command action of the last several commands sent to device>
|
|
last_cmd_index = <0 based last command index>
|
|
last_cmd_resp_id = <command id of the last several command responses received from device>
|
|
last_cmd_resp_index = <0 based last command response index>
|
|
last_event = <event id of the last several events received from device>
|
|
last_event_index = <0 based last event index>
|
|
num_cmd_h2c_fail = <number of commands failed to send to device>
|
|
num_cmd_sleep_cfm_fail = <number of sleep confirm failed to send to device>
|
|
num_tx_h2c_fail = <number of data packets failed to send to device>
|
|
num_cmdevt_c2h_fail = <number of commands/events failed to receive from device>
|
|
num_rx_c2h_fail = <number of data packets failed to receive from device>
|
|
num_int_read_fail = <number of interrupt read failures>
|
|
last_int_status = <last interrupt status>
|
|
num_evt_deauth = <number of deauthenticated events received from device>
|
|
num_evt_disassoc = <number of disassociated events received from device>
|
|
num_evt_link_lost = <number of link lost events received from device>
|
|
num_cmd_deauth = <number of deauthenticate commands sent to device>
|
|
num_cmd_assoc_ok = <number of associate commands with success return>
|
|
num_cmd_assoc_fail = <number of associate commands with failure return>
|
|
cmd_sent = <0/1, send command resources available/sending command to device>
|
|
data_sent = <0/1, send data resources available/sending data to device>
|
|
mp_rd_bitmap = <SDIO multi-port read bitmap>
|
|
curr_rd_port = <SDIO multi-port current read port>
|
|
mp_wr_bitmap = <SDIO multi-port write bitmap>
|
|
curr_wr_port = <SDIO multi-port current write port>
|
|
txbd_rdptr = <PCIE transmit read pointer>
|
|
txbd_wrptr = <PCIE transmit write pointer>
|
|
rxbd_rdptr = <PCIE recieve read pointer>
|
|
rxbd_wrptr = <PCIE recieve write pointer>
|
|
eventbd_rdptr = <PCIE event read pointer>
|
|
eventbd_wrptr = <PCIE event write pointer>
|
|
cmd_resp_received = <0/1, no cmd response to process/response received and yet to process>
|
|
event_received = <0/1, no event to process/event received and yet to process>
|
|
tx_cmd_urb_pending = <number of URB pending for cmd transmit>
|
|
tx_data_urb_pending = <number of URB pending for data transmit>
|
|
rx_cmd_urb_pending = <number of URB pending for cmd receive>
|
|
rx_data_urb_pending = <number of URB pending for data receive>
|
|
ioctl_pending = <number of ioctl pending>
|
|
tx_pending = <number of Tx packet pending>
|
|
rx_pending = <number of Rx packet pending>
|
|
lock_count = <number of lock used>
|
|
malloc_count = <number of malloc done>
|
|
mbufalloc_count = <number of mlan_buffer allocated>
|
|
malloc_cons_count = <number of consistent malloc done>
|
|
main_state = <current state of the main process>
|
|
sdiocmd53w = <SDIO Cmd53 write status>
|
|
sdiocmd53r = <SDIO Cmd52 read status>
|
|
hs_skip_count = <number of skipped suspends>
|
|
hs_force_count = <number of forced suspends>
|
|
|
|
Issue SDIO cmd52 read/write through proc.
|
|
Usage:
|
|
echo "sdcmd52rw=<func> <reg> [data]" > /proc/mwlan/adapterX/config
|
|
where the parameters:
|
|
func: The function number to use (0-7)
|
|
reg: The address of the register
|
|
data: The value to write, read if the value is absent
|
|
For SDIO MMC driver, only function 0 and WLAN function access is allowed.
|
|
And there is a limitation for function 0 write, only vendor specific CCCR
|
|
registers (0xf0 -0xff) are permiited.
|
|
Examples:
|
|
echo "sdcmd52rw= 0 4" > /proc/mwlan/adapterX/config # read func 0 address 4
|
|
cat /proc/mwlan/adapterX/config # display the register value
|
|
echo "sdcmd52rw= 1 3 0xf" > /proc/mwlan/adapterX/config # write 0xf to func 1 address 3
|
|
|
|
Use dmesg or cat /var/log/debug to check driver debug messages.
|
|
To log driver debug messages to file,
|
|
a) Edit /etc/syslog.conf, add one line "*.debug /var/log/debug"
|
|
on kernel 2.6.24 or later, edit /etc/rsyslog.conf instead
|
|
b) touch /var/log/debug (if the file doesn't exist)
|
|
c) service syslog restart
|
|
on kernel 2.6.24 or later, service rsyslog restart
|
|
|
|
Update /proc/sys/kernel/printk to change message log levels.
|
|
For example,
|
|
echo 6 > /proc/sys/kernel/printk (messages with a higher priority than 6
|
|
will be printed to the console)
|
|
echo 15 > /proc/sys/kernel/printk (all messages will be printed to console)
|
|
|
|
4) FOR IWPRIV COMMAND
|
|
|
|
NAME
|
|
This manual describes the usage of private commands used in NXP MLAN
|
|
Linux Driver.
|
|
|
|
To use parameters as hex format, a '0x' must precede it for the parameters to
|
|
be parsed properly.
|
|
|
|
SYNOPSIS
|
|
iwpriv <mlanX> <command> [sub-command] ...
|
|
|
|
iwpriv mlanX version
|
|
iwpriv mlanX verext
|
|
iwpriv mlanX getsignal [m] [n]
|
|
iwpriv mlanX antcfg [m] [n]
|
|
iwpriv mlanX regioncode [n]
|
|
iwpriv mlanX cfpcode [m] [n]
|
|
iwpriv mlanX wwscfg [m]
|
|
iwpriv mlanX esuppmode
|
|
iwpriv mlanX passphrase <ssid/psk/passphrase>
|
|
iwpriv mlanX httxcfg [<m>] [<n>]
|
|
iwpriv mlanX htcapinfo [<m>] [<n>]
|
|
iwpriv mlanX addbapara <m> <n> <o> <p> <q>
|
|
iwpriv mlanX aggrpriotbl <n>
|
|
iwpriv mlanX addbareject <n>
|
|
iwpriv mlanX txbufcfg
|
|
iwpriv mlanX amsduaggrctrl <n>
|
|
iwpriv mlanX httxbfcap [cap]
|
|
iwpriv mlanX httxbfcfg "<action>[;GlobalData/tsData/interval/txPeerData/snrData]"
|
|
iwpriv mlanX mpactrl [tx_ena] [rx_ena] [tx_size] [rx_size] [tx_ports] [rx_ports]
|
|
iwpriv mlanX deepsleep [n] [m]
|
|
iwpriv mlanX usbsuspend
|
|
iwpriv mlanX usbresume
|
|
iwpriv mlanX hscfg [condition [[GPIO# [gap]]]]
|
|
iwpriv mlanX hssetpara condition [GPIO# [gap]]
|
|
iwpriv mlanX deauth [n]
|
|
iwpriv mlanX radioctrl
|
|
iwpriv mlanX reassoctrl [n]
|
|
iwpriv mlanX bandcfg [l] [m] [n]
|
|
iwpriv mlanX getlog
|
|
iwpriv mlanX 11dcfg
|
|
iwpriv mlanX 11dclrtbl
|
|
iwpriv mlanX wmmcfg [n]
|
|
iwpriv mlanX hotspotcfg [n]
|
|
iwpriv mlanX txpowercfg [<RateIndex> [<MinPwr> [<MaxPwr> <step>]]]
|
|
iwpriv mlanX qoscfg
|
|
iwpriv mlanX getdatarate
|
|
iwpriv mlanX txratecfg [n]
|
|
iwpriv mlanX bcninterval [n]
|
|
iwpriv mlanX sysclock [clk1] [clk2] [clk3] [clk4]
|
|
iwpriv mlanX drvdbg [n]
|
|
iwpriv mlanX mgmtframectrl
|
|
iwpriv mlanX warmreset
|
|
iwpriv mlanX regrdwr <type> <offset> [value]
|
|
iwpriv mlanX rdeeprom <offset> <length>
|
|
iwpriv mlanX memrdwr <address> [value]
|
|
iwpriv mlanX inactivityto <n> <m> <l> [k]
|
|
iwpriv mlanX sdioclock <n>
|
|
iwpriv mlanX sdcmd52rw <FN no.> <address> [data]
|
|
iwpriv mlanX scancfg [t] [m] [p] [s] [a] [b] [ext]
|
|
iwpriv mlanX sleeppd [n]
|
|
iwpriv mlanX pscfg [k] [d] [l] ...
|
|
iwpriv mlanX getkey
|
|
iwpriv mlanX associate "<bssid> <ssid>"
|
|
iwpriv mlanX sleepparams [<p1> <p2> <p3> <p4> <p5> <p6>]
|
|
iwpriv mlanX authtype [n]
|
|
iwpriv mlanX powercons [n]
|
|
iwpriv mlanX htstreamcfg [n]
|
|
iwpriv mlanX ipaddr ["<op>;<ipaddr>"]
|
|
iwpriv mlanX macctrl [n]
|
|
iwpriv mlanX dfstesting [<user_cac_pd> <user_nop_pd> <no_chan_change> <fixed_chan_num>]
|
|
iwpriv mlanX thermal
|
|
iwpriv mlanX indrstcfg <ir_mode> [gpio_pin]
|
|
|
|
DESCRIPTION
|
|
Those commands are used to send additional commands to the NXP MLAN
|
|
card via the Linux device driver.
|
|
|
|
The mlanX parameter specifies the network device that is to be used to
|
|
perform this command on. It could be mlan0, mlan1 etc.
|
|
|
|
version
|
|
This is used to get the current version of the driver and the firmware.
|
|
|
|
verext
|
|
Retrieve and display an extended version string from the firmware
|
|
|
|
Usage:
|
|
iwpriv mlanX verext [#]
|
|
|
|
where [#] is an optional argument to retrieve a specific version string,
|
|
omission of the argument retrieves the 0 indexed string.
|
|
|
|
getsignal
|
|
This command gets the last and average value of RSSI, SNR and NF of
|
|
Beacon and Data.
|
|
Note: This command is available only when STA is connected.
|
|
|
|
where value of m is:
|
|
1 -- RSSI (Receive Signal Strength Indication)
|
|
2 -- SNR (Signal to Noise Ratio)
|
|
3 -- NF (Noise Floor)
|
|
where value of n is:
|
|
1 -- Beacon last
|
|
2 -- Beacon average
|
|
3 -- Data last
|
|
4 -- Data average
|
|
|
|
Examples:
|
|
iwpriv mlan0 getsignal 1 : Get the RSSI info (beacon last, beacon
|
|
average, data last and data average)
|
|
iwpriv mlan0 getsignal 3 4 : Get the NF of data average
|
|
iwpriv mlan0 getsignal 2 1 : Get the SNR of beacon last
|
|
iwpriv mlan0 getsignal : Get all of the signal info
|
|
mlan0 getsignal:-32 -33 -35 -36 67 59 63 56 -99 -92 -98 -92
|
|
RSSI info: beacon last -32, beacon average -33, data last -35, data average -36
|
|
SNR info: beacon last 67, beacon average 59, data last 63, data average 56
|
|
NF info: beacon last -99, beacon average -92, data last -98, data average -92
|
|
|
|
antcfg
|
|
This command is used to set/get the mode of Tx/Rx path.
|
|
|
|
where value of m is:
|
|
Bit 0 -- Tx Path A
|
|
Bit 1 -- Tx Path B
|
|
Bit 0-1 -- Tx Path A+B
|
|
For 9097/9098, LOW BYTE for 2G setting
|
|
Bit 8 -- Tx Path A
|
|
Bit 9 -- Tx Path B
|
|
Bit 8-9 -- Tx Path A+B
|
|
For 9097/9098, HIGH BYTE for 5G setting
|
|
|
|
where value of n is:
|
|
Bit 0 -- Rx Path A
|
|
Bit 1 -- Rx Path B
|
|
Bit 0-1 -- Rx Path A+B
|
|
For 9097/9098, LOW BYTE for 2G setting
|
|
Bit 8 -- Rx Path A
|
|
Bit 9 -- Rx Path B
|
|
Bit 8-9 -- Rx Path A+B
|
|
For 9097/9098, HIGH BYTE for 5G setting
|
|
The Tx path setting (m) is used if Rx path (n) is not provided.
|
|
|
|
Examples:
|
|
iwpriv mlan0 antcfg : Get Tx and Rx path
|
|
iwpriv mlan0 antcfg 3 : Set Tx and Rx path to A+B
|
|
iwpriv mlan0 antcfg 1 3 : Set Tx path to A and Rx path to A+B
|
|
mlanutl mlan0 antcfg 0x103 : Set Tx and Rx path to A+B on 2G and Tx and Rx path to A on 5G
|
|
mlanutl mlan0 antcfg 0x103 0x103 : Set Tx path to A+B and Rx path to A+B on 2G, and Tx and Rx path to A on 5G
|
|
|
|
regioncode
|
|
This command is used to set/get the region code in the station.
|
|
Note: This command should be issued at beginning before band/channel selection
|
|
and association.
|
|
|
|
where value is 'region code' for various regions like
|
|
USA FCC, Canada IC, Europe ETSI, Japan ...
|
|
The special code (0xff) is used for Japan to support channel 1-14 in B/G/N mode.
|
|
|
|
Examples:
|
|
iwpriv mlan0 regioncode : Get region code
|
|
iwpriv mlan0 regioncode 0x10 : Set region code to USA (0x10)
|
|
|
|
Note : in some case regioncode will be 0 after updated countycode or 80211d
|
|
i.e. mlanutl mlanX countrycode (CA, JP, CN, DE, ES AT, BR, RU)
|
|
or uaputl.exe sys_cfg_80211d state 1 country (CA, JP, CN, DE, ES AT, BR, RU)
|
|
Please use cfp instead of it.
|
|
|
|
cfpcode
|
|
This command is used to set/get the Channel-Frequency-Power table codes.
|
|
The region table can be selected through region code.
|
|
The current configuration is returned if no parameter provided.
|
|
|
|
where the parameters are,
|
|
[m]: code of the CFP table for 2.4GHz (0: unchanged)
|
|
[n]: code of the CFP table for 5GHz (0 or not provided: unchanged)
|
|
|
|
Examples:
|
|
iwpriv mlan0 cfpcode : Get current configuration
|
|
iwpriv mlan0 cfpcode 0x30 : Set 2.4GHz CFP table code 0x30 (EU),
|
|
keep 5GHz table unchanged
|
|
iwpriv mlan0 cfpcode 0x10 5 : Set 2.4GHz CFP table code 0x10 (USA)
|
|
and 5GHz table code 5
|
|
|
|
wwscfg
|
|
This command is used to set/get the WWS (World Wide Safe) mode.
|
|
|
|
where value of m is:
|
|
0 -- Disable WWS mode (default)
|
|
1 -- Enable WWS mode
|
|
|
|
Examples:
|
|
iwpriv mlan0 wwscfg : Get WWS mode
|
|
iwpriv mlan0 wwscfg 1 : Enable WWS mode
|
|
iwpriv mlan0 wwscfg 0 : Disable WWS mode
|
|
|
|
esuppmode
|
|
This command is used to get the current RSN mode and active pairwise/group
|
|
cipher for WPA/WPA2 mode.
|
|
Note: This command is available only when STA is connected.
|
|
|
|
These are bits settings used to indicate each RSN mode.
|
|
Bit 0 : No RSN
|
|
Bit 1-2 : RFU
|
|
Bit 3 : WPA
|
|
Bit 4 : WPA-NONE
|
|
Bit 5 : WPA2
|
|
Bit 6 : AES
|
|
Bit 7-15 : RFU
|
|
|
|
These are bits settings used to indicate each pairwise and group cipher.
|
|
Bit 0 : RFU
|
|
Bit 1 : RFU
|
|
Bit 2 : TKIP
|
|
Bit 3 : AES
|
|
Bit 2-7 : RFU
|
|
|
|
Example:
|
|
iwpriv mlan0 esuppmode : Get RSN mode and pairwise/group cipher
|
|
8 4 4
|
|
(The current RSN mode is WPA, active pairwise cipher is TKIP and
|
|
active group cipher is TKIP.)
|
|
|
|
passphrase
|
|
This command is used to set/get passphrase for WPA-PSK/WPA2-PSK mode.
|
|
|
|
Where <n>
|
|
ASCII string for ssid/passphrase/psk.
|
|
|
|
This passphrase is used as password if WPA3 SAE protocol is configured, so please
|
|
use extremely difficult to guess password to protect from attacks.
|
|
|
|
Also setting psk for WPA3 SAE protocol is not possible, as new psk gets generated
|
|
everytime in protocol flow.
|
|
|
|
1) "0;<ssid=valid ssid>" - This will get the passphrase, AKMP
|
|
for specified ssid, if none specified then it will get all.
|
|
|
|
Example:
|
|
iwpriv mlan0 passphrase "0;ssid=nxp"
|
|
|
|
2) "1;<psk=64 byte hexpsk>;<passphrase=1-63 byte passphare>
|
|
<ssid=valid ssid>" - Passphrase and psk cannot be provided for the same SSID.
|
|
This command takes only one SSID at a time, If ssid= is present it should contain
|
|
a passphrase or psk. If no arguments are provided then AKMP=802.1x, and passphrase
|
|
should be provided after association.
|
|
End of each parameter should be followed by a ';'(except for the last parameter)
|
|
as the delimiter. If ';' or '/' has to be used in an SSID then a '/' should be preceded
|
|
to ';' or '/' as a escape.
|
|
|
|
Examples:
|
|
iwpriv mlan0 passphrase "1;ssid=nxpAP;passphrase=abcdefgd"
|
|
iwpriv mlan0 passphrase "1;ssid=nxp AP;psk=<64 bytes hexpsk>"
|
|
|
|
If user wants to input the ssid as "nxp; AP" then command has to be
|
|
iwpriv mlan0 passphrase "1;ssid=nxp/; AP;passphrase=abcdefgh"
|
|
|
|
If user wants to input the ssid as "//;" then command has to be
|
|
iwpriv mlan0 passphrase "1;ssid=/////;;passphrase=abcdefgh"
|
|
|
|
3) "2;<ssid=valid ssid>" - This will clear the passphrase
|
|
for specified ssid, if none specified then it will clear all.
|
|
|
|
Examples:
|
|
iwpriv mlan0 passphrase "2;ssid=nxp"
|
|
iwpriv mlan0 passphrase "2" : Clear all profiles and disable embedded supplicant
|
|
|
|
httxcfg
|
|
This command is used to configure various 11n specific configuration
|
|
for transmit (such as Short GI, Channel BW and Green field support)
|
|
|
|
where <m> is <txcfg>
|
|
This is a bitmap and should be used as following
|
|
Bit 15-8: Reserved set to 0
|
|
Bit 7: STBC enable/disable
|
|
Bit 6: Short GI in 40 Mhz enable/disable
|
|
Bit 5: Short GI in 20 Mhz enable/disable
|
|
Bit 4: Green field enable/disable
|
|
Bit 3-2: Reserved set to 1
|
|
Bit 1: 20/40 Mhz enable disable.
|
|
Bit 0: LDPC enable/disable
|
|
|
|
When Bit 1 is set then firmware could transmit in 20Mhz or 40Mhz based
|
|
on rate adaptation. When this bit is reset then firmware will only
|
|
transmit in 20Mhz.
|
|
|
|
where <n> is <band>
|
|
<band> - This is the band info for <txcfg> settings.
|
|
0: Settings for both 2.4G and 5G bands
|
|
1: Settings for 2.4G band
|
|
2: Settings for 5G band
|
|
|
|
Examples:
|
|
iwpriv mlanX httxcfg
|
|
This will display HT Tx configuration.
|
|
If the configurations for 2.4G and 5G are different,
|
|
the first value is for 2.4G and the second value is for 5G.
|
|
Otherwise, it will display a single value for both bands.
|
|
|
|
iwpriv mlanX httxcfg 0x62
|
|
This will enable 20/40 and Short GI but will disable Green field for 2.4G and 5G band.
|
|
|
|
iwpriv mlanX httxcfg 0x30 1
|
|
This will enable Short GI 20 Mhz and Green field for 2.4G band.
|
|
|
|
The default value is 0x20 for 2.4G and 0x62 for 5G.
|
|
|
|
Note:- If 20/40 MHz support is disabled in htcapinfo, device will not transmit
|
|
in 40 MHz even 20/40 MHz is enabled in httxcfg.
|
|
|
|
htcapinfo
|
|
This command is used to configure some of parameters in HTCapInfo IE
|
|
(such as Short GI, Channel BW, and Green field support)
|
|
|
|
where <m> is <capinfo>
|
|
<capinfo> - This is a bitmap and should be used as following
|
|
Bit 29: Green field enable/disable
|
|
Bit 26: Rx STBC Support enable/disable. (As we support
|
|
single spatial stream only 1 bit is used for Rx STBC)
|
|
Bit 24: Short GI in 40 Mhz enable/disable
|
|
Bit 23: Short GI in 20 Mhz enable/disable
|
|
Bit 17: 20/40 Mhz enable disable.
|
|
Bit 8: Enable/disable 40Mhz Intolarent bit in ht capinfo.
|
|
0 will reset this bit and 1 will set this bit in
|
|
htcapinfo attached in assoc request.
|
|
All others are reserved and should be set to 0.
|
|
|
|
Setting of any other bits will return error.
|
|
|
|
where <n> is <band>
|
|
<band> - This is the band info for <capinfo> settings.
|
|
0: Settings for both 2.4G and 5G bands
|
|
1: Settings for 2.4G band
|
|
2: Settings for 5G band
|
|
|
|
Examples:
|
|
iwpriv mlanX htcapinfo
|
|
This will display HT capabilties information.
|
|
If the information for 2.4G and 5G is different,
|
|
the first value is for 2.4G and the second value is for 5G.
|
|
Otherwise, it will display a single value for both bands.
|
|
|
|
iwpriv mlanX htcapinfo 0x1820000
|
|
This will enable Short GI, Channel BW to 20/40 and disable Green field support for 2.4G and 5G band.
|
|
|
|
iwpriv mlanX htcapinfo 0x800000 2
|
|
This will enable Short GI, Channel BW to 20 only, No Rx STBC support and disable Green field support for 5G band.
|
|
|
|
The default value is 0x4800000 for 2.4G and 0x5820000 for 5G.
|
|
|
|
Note:- This command can be issued any time but it will only come to effect from
|
|
next association. (as HTCapInfo is sent only during Association).
|
|
|
|
addbapara
|
|
This command can be used to update the default ADDBA parameters.
|
|
|
|
where <m> is <timeout>
|
|
<timeout> - This is the block ack timeout for ADDBA request.
|
|
0 : Disable (recommended for throughput test)
|
|
1 - 65535 : Block Ack Timeout in TU
|
|
|
|
where <n> is <txwinsize>
|
|
<txwinsize> - Window size for ADDBA request. (16 is recommended and default value)
|
|
|
|
where <o> is <rxwinsize>
|
|
<rxwinsize> - Window size for ADDBA response. (48 is recommended and 32 is default value)
|
|
(16 is recommended for IWNCOMM AP in WAPI throughput test)
|
|
|
|
Current window size limit for Tx as well as Rx is 1023.
|
|
|
|
where <p> is <txamsdu>
|
|
<txamsdu> - amsdu support for ADDBA request. (1 is default value)
|
|
0: disable amsdu in ADDBA request
|
|
1: enable amsdu in ADDBA request
|
|
|
|
where <q> is <rxamsdu>
|
|
<rxamsdu> - amsdu support for ADDBA response. (1 is default value)
|
|
0: disable amsdu in ADDBA response
|
|
1: enable amsdu in ADDBA response
|
|
|
|
eg:
|
|
iwpriv mlanX addbapara - This command will get the current addba params
|
|
iwpriv mlanX addbapara 1000 64 8 0 0 - This will change the ADDBA timeout to (1000 * 1024) us,
|
|
txwinsize to 64 and rxwinsize to 8 and disable amdsu in ADDBA request/response.
|
|
|
|
The default setting is 65535 16 32 1 1.
|
|
|
|
In case the ADDBA timeout value is updated then a ADDBA is sent for all streams
|
|
to update the timeout value.
|
|
|
|
In case txwinsize and/or rxwinsize is updated, the effect could only be seen on
|
|
next ADDBA request/response. The current streams will not be affected with this
|
|
change.
|
|
|
|
In case of txamsdu/rxamsdu is updated, the effect could only be seen on
|
|
next ADDBA request/response. The current streams will not be affected with this
|
|
change. AMSDU in AMPDU stream will be enabled when AP support this feature
|
|
and AMSDU is enabled in aggrpriotbl.
|
|
|
|
aggrpriotbl
|
|
This command is used set/get the priority table for AMPDU/AMSDU traffic per tid.
|
|
This command can also be used to disable AMPDU/AMSDU for a given tid.
|
|
In case of AMPDU this priority table will be used to setup block ack (to make
|
|
sure the highest priority tid always uses AMPDU as we have limited AMPDU streams)
|
|
|
|
where <m0> <n0> <m1> <n1> ... <m7> <n7>
|
|
|
|
<mx> - This is priority for Tid0 for AMPDU packet. A priority could be any
|
|
values between 0 - 7, 0xff to disable aggregation.
|
|
<nx> - This is priority for Tid0 for AMSDU packet. A priority could be any
|
|
values between 0 - 7, 0xff to disable aggregation.
|
|
|
|
eg:
|
|
iwpriv mlanX aggrpriotbl - This command will get the current Priority table for AMPDU and AMSDU.
|
|
<2 2 0 0 1 1 3 3 4 4 5 5 255 255 255 255>. This is read as
|
|
<"Prio for AMPDU for Tid0" "Prio for AMSDU for Tid0"
|
|
"Prio for AMPDU for Tid1" "Prio for AMSDU for Tid1" and so on
|
|
iwpriv mlanX aggrpriotbl 2 2 0 0 1 1 3 3 4 4 5 5 255 255 255 255 -
|
|
This will set the priority table for AMPDU and AMSDU
|
|
Priority for Tid0/AMPDU = 2, Tid0/AMSDU = 2, Tid1/AMPDU = 0, Tid1/AMSDU = 0
|
|
and so on. Aggregation for Tid6 and Tid7 are disabled.
|
|
Here higher the priority number, higher the priority (i.e. 7
|
|
has higher priority than 6). Similarly for AMSDU.
|
|
iwpriv mlanX aggrpriotbl 0xff 2 0xff 0 0xff 1 0xff 3 0xff 4 0xff 5 0xff 0xff 0xff 0xff - This will disable
|
|
AMPDU for all the TIDs but will still keep AMSDU enabled to Tid0 to Tid5
|
|
|
|
The default setting is 2 255 0 255 1 255 3 255 4 255 5 255 255 255 255 255.
|
|
|
|
A delBA should be seen in case a disable happens on a TID for which AMPDU stream
|
|
is currently setup.
|
|
|
|
Note:- This command should only be issue in disconnected state.
|
|
|
|
addbareject
|
|
This command is used set/get the addbareject table for all the TIDs.
|
|
This command can also be used to enable rejection of ADDBA requests for a given tid.
|
|
|
|
where <m0> <m1> ... <m7>
|
|
|
|
<mX> - This can be 0/1 for TidX. 1 enables rejection of ADDBA request for TidX and
|
|
0 would accept any ADDBAs for TidX.
|
|
|
|
eg:
|
|
iwpriv mlanX addbareject - This command will get the current table.
|
|
[0 0 0 0 0 0 0 0]. ADDBA would be accepted for all TIDs. This is the default state.
|
|
|
|
iwpriv mlanX addbareject 0 0 1 1 0 0 0 0 - This command will accept ADDBA requests for
|
|
Tid [0,1,4,5,6,7] and reject ADDBA requests for Tid [2,3]
|
|
|
|
iwpriv mlanX addbareject 1 1 1 1 1 1 1 1 - This will enable rejection of ADDBA requests for
|
|
all Tids.
|
|
|
|
Note:- This command should only be issue in disconnected state.
|
|
|
|
txbufcfg
|
|
This command can be used to get current buffer size.
|
|
|
|
eg:
|
|
iwpriv mlanX txbufcfg - This will display the current buffer size.
|
|
|
|
Note:- The actual tx buf size will depends on AP's capability and max transmit buffer size.
|
|
|
|
amsduaggrctrl
|
|
This command could be used to enable/disable a feature where firmware gives feedback to driver
|
|
regarding the optimal AMSDU buffer size to use with the current rate. Firmware will use the
|
|
current rate to decide the buffer size we could transmit. The max buffer size will still be
|
|
limited by buffer size provided in txbufcfg. (i.e. if the txbufcfg is 4K, then we could only transmit
|
|
4K/2K AMSDU packets, if the txbufcfg is 8K then we could transmit 8k/4k/2k based on current rate)
|
|
|
|
If enabled AMSDU buffer size at various rates will be as follows
|
|
|
|
1. Legacy B/G rate.
|
|
No AMSDU aggregation.
|
|
|
|
2. BW20 HT Rate:
|
|
When TX rate goes down,
|
|
MCS 7, 6, 5, 4:
|
|
a 8K aggregation size (if TX buffer size is 8K)
|
|
b 4K aggregation size (if TX buffer size is 4K)
|
|
c 2K aggregation size (if TX buffer size is 2K)
|
|
|
|
MCS 3, 2:
|
|
a 4K aggregation size (if TX buffer size is 8K/4K)
|
|
b 2K aggregation size (if TX buffer size is 2K)
|
|
|
|
MCS 1, 0:
|
|
a No aggregation
|
|
|
|
When TX rate goes up,
|
|
MCS 7, 6, 5:
|
|
a 8K aggregation size (if TX buffer size is 8K)
|
|
b 4K aggregation size (if TX buffer size is 4K)
|
|
c 2K aggregation size (if TX buffer size is 2K)
|
|
|
|
MCS 4, 3:
|
|
a 4K aggregation size (if TX buffer size is 8K/4K)
|
|
b 2K aggregation size (if TX buffer size is 2K)
|
|
|
|
MCS 2, 1, 0:
|
|
a No aggregation
|
|
|
|
3. BW40 HT Rate:
|
|
When TX rate goes down,
|
|
MCS 7, 6, 5, 4, 3, 2, 1:
|
|
a 8K aggregation size (if TX buffer size is 8K)
|
|
b 4K aggregation size (if TX buffer size is 4K)
|
|
c 2K aggregation size (if TX buffer size is 2K)
|
|
|
|
MCS 0:
|
|
a No aggregation
|
|
|
|
When TX rate goes up,
|
|
MCS 7, 6, 5, 4, 3:
|
|
a 8K aggregation size (if TX buffer size is 8K)
|
|
b 4K aggregation size (if TX buffer size is 4K)
|
|
c 2K aggregation size (if TX buffer size is 2K)
|
|
|
|
MCS 2, 1, 0:
|
|
a No aggregation
|
|
|
|
where <n> is 0/1 (for disable/enable)
|
|
|
|
eg:
|
|
iwpriv mlanx amsduaggrctrl 1 - Enable this feature
|
|
iwpriv mlanx amsduaggrctrl 0 - Disable this feature
|
|
iwpriv mlanx amsduaggrctrl - This will get the enable/disable flag
|
|
and the current AMSDU buffer size). The AMSDU buffer size returned is only
|
|
valid after association as before association there is no rate info.
|
|
|
|
Note:- This command to enable/disable could be given anytime (before/after
|
|
association). This feature is enabled by default by the driver during
|
|
initialization.
|
|
|
|
httxbfcap
|
|
This command is used to set/get the TX beamforming capabilities.
|
|
|
|
Usage:
|
|
iwpriv mlanX httxbfcap [cap]
|
|
|
|
where the parameters are,
|
|
cap: TX beamforming capabilities
|
|
Bit 0 : Implicit TX BF receiving capable
|
|
Bit 1 : RX staggered sounding capable
|
|
Bit 2 : TX staggered sounding capable
|
|
Bit 3 : RX NDP capable
|
|
Bit 4 : TX NDP capable
|
|
Bit 5 : Implicit TX BF capable
|
|
Bit 6-7 : Calibration
|
|
0: - not supported
|
|
1: - STA can respond to a calibration request using
|
|
the CSI Report, but cannot initiate calibration
|
|
2: - reserved
|
|
3: - STA can both initiate and respond to a calibration request
|
|
Bit 8 : Explicit CSI TX BF capable
|
|
Bit 9 : Explicit non-compressed steering capable
|
|
Bit 10 : Explicit compressed steering capable
|
|
Bit 11-12: Explicit TX BF CSI feedback
|
|
0: - not supported
|
|
1: - delayed feedback
|
|
2: - immediate feedback
|
|
3: - delayed and immediate feedback
|
|
Bit 13-14: Explicit non-compressed BF feedback capable
|
|
0: - not supported
|
|
1: - delayed feedback
|
|
2: - immediate feedback
|
|
3: - delayed and immediate feedback
|
|
Bit 15-16: Explicit compressed BF feedback capable
|
|
0: - not supported
|
|
1: - delayed feedback
|
|
2: - immediate feedback
|
|
3: - delayed and immediate feedback
|
|
Bit 17-18: Minimal grouping
|
|
0: - no grouping (STA supports groups of 1)
|
|
1: - groups of 1, 2
|
|
2: - groups of 1, 4
|
|
3: - groups of 1, 2, 4
|
|
Bit 19-20: CSI number of beamformer antennas supported
|
|
0: - single TX antenna sounding
|
|
1: - 2 TX antenna sounding
|
|
2: - 3 TX antenna sounding
|
|
3: - 4 TX antenna sounding
|
|
Bit 21-22: Non-compressed steering number of beamformer antennas supported
|
|
0: - single TX antenna sounding
|
|
1: - 2 TX antenna sounding
|
|
2: - 3 TX antenna sounding
|
|
3: - 4 TX antenna sounding
|
|
Bit 23-24: Compressed steering number of beamformer antennas supported
|
|
0: - single TX antenna sounding
|
|
1: - 2 TX antenna sounding
|
|
2: - 3 TX antenna sounding
|
|
3: - 4 TX antenna sounding
|
|
Bit 25-26: CSI max number of rows beamformer supported
|
|
0: - single row of CSI
|
|
1: - 2 rows of CSI
|
|
2: - 3 rows of CSI
|
|
3: - 4 rows of CSI
|
|
Bit 27-28: Channel estimation capability
|
|
0: - 1 space time stream
|
|
1: - 2 space time streams
|
|
2: - 3 space time streams
|
|
3: - 4 space time streams
|
|
Bit 29-31: Reserved
|
|
|
|
Examples:
|
|
iwpriv mlan0 httxbfcap : Get the current TX BF capabilities
|
|
iwpriv mlan0 httxbfcap 0x0000001F : Set the TX BF capabilities of the
|
|
Implicit TX BF receiving capable,
|
|
RX staggered sounding capable,
|
|
TX staggered sounding capable,
|
|
RX NDP capable and TX NDP capable
|
|
|
|
httxbfcfg
|
|
This command is used to configure the TX beamforming options.
|
|
Note: Any new subcommand should be inserted in the second
|
|
argument and each argument of the sub command should be
|
|
separated by semicolon. For global configuration, the
|
|
arguments should be separated by space.
|
|
|
|
Usage:
|
|
iwpriv mlanX httxbfcfg "<action>[;GlobalData/tsData/interval/txPeerData/snrData]"
|
|
|
|
where the parameters are,
|
|
action: TX beamforming action
|
|
0: Control global parameters for beamforming
|
|
1: Performs NDP Sounding for PEER
|
|
2: TX BF interval in milliseconds
|
|
3: Enable/Disable beamforming/sounding for a particular peer
|
|
4: TX BF SNR Threshold for peer
|
|
.. <for new subcommand>
|
|
GlobalData: Global parameter arguments.
|
|
It contains beamforming enable, sounding enable, FB type, snr_threshold
|
|
sounding interval, Beamformig mode values seperated by space.
|
|
Syntax:
|
|
iwpriv mlanX httxbfcfg <action>;<beamforming enable> <sounding enable> <FB type>
|
|
<snr_threshold> <sounding interval> <Beamforming mode>
|
|
tsData: Trigger sounding for PEER specific arguments,
|
|
it contains PEER MAC and status
|
|
interval: TX BF interval in milliseconds
|
|
txPeerData: Enable/Disable beamforming/sounding for the indicated peer,
|
|
it contains PEER MAC, sounding, beamfoming options and FB type;
|
|
snrData: TX BF SNR Threshold for peer, it contains PEER MAC and SNR
|
|
|
|
Examples:
|
|
iwpriv mlan0 httxbfcfg "0" : Get current global configuration parameter
|
|
iwpriv mlan0 httxbfcfg "2;00:50:43:20:BF:64" : Get the TX BF periodicity for a given peer
|
|
iwpriv mlan0 httxbfcfg "3" : Get the list of MAC addresses that have
|
|
beamforming and/or sounding enabled
|
|
iwpriv mlan0 httxbfcfg "4" : Get the list of PEER MAC, SNR tuples
|
|
programmed into the firmware.
|
|
iwpriv mlan0 httxbfcfg "0;0 0 3 10 500 5" : Disable beamforming, sounding, set FB type
|
|
to 3, snr threshold to 10, sounding interval
|
|
to 500 ms and beamforming mode to 5
|
|
iwpriv mlan0 httxbfcfg "1;00:50:43:20:BF:64" : Perform NDP Trigger sounding to peer
|
|
00:50:43:20:BF:64
|
|
iwpriv mlan0 httxbfcfg "2;00:50:43:20:BF:64;500" : Set TX BF periodicity for peer 00:50:43:20:BF:64
|
|
to 500 milliseconds
|
|
iwpriv mlan0 httxbfcfg "3;00:50:43:20:BF:43;1;0;3" : Enable beamforming, disable sounding and set
|
|
FB type to 3 for peer 00:50:43:20:BF:43
|
|
iwpriv mlan0 httxbfcfg "4;00:50:43:20:BF:24;43" : Set TX BF SNR threshold to peer
|
|
00:50:43:20:BF:24 with SNR 43
|
|
|
|
mgmtframectrl
|
|
This command is used to get/set mask for the management frames which needs to be forwarded to application layer.
|
|
|
|
Usage:
|
|
iwpriv mlanX mgmtframectrl [m]
|
|
|
|
where the parameter [m] is the bit mask of management frame reception.
|
|
Following are the bit definitions.
|
|
Bit 0 : Association Request
|
|
Bit 1 : Association Response
|
|
Bit 2 : Re-Association Request
|
|
Bit 3 : Re-Association Response
|
|
Bit 4 : Probe Request
|
|
Bit 5 : Probe Response
|
|
Bit 8 : Beacon Frames
|
|
|
|
Examples:
|
|
iwpriv mlan0 mgmtframectrl : Get the current Mgmt Frame forwarding mask
|
|
iwpriv mlan0 mgmtframectrl 0x0020 : Bit 5 is set, Forward probe response
|
|
frames to application layer
|
|
|
|
mpactrl
|
|
This command is used to set/get the Tx, Rx SDIO aggregation parameters.
|
|
Note: The parameters can be set only in disconnected state.
|
|
|
|
Usage:
|
|
iwpriv mlanX mpactrl [tx_ena] [rx_ena] [tx_size] [rx_size] [tx_ports] [rx_ports]
|
|
|
|
where the parameter are:
|
|
[tx_ena]: Enable/disable (1/0) Tx MP-A
|
|
[rx_ena]: Enable/disable (1/0) Rx MP-A
|
|
[tx_size]: Size of Tx MP-A buffer
|
|
[rx_size]: Size of Rx MP-A buffer
|
|
[tx_ports]: Max ports (1-16) for Tx MP-A
|
|
[rx_ports]: Max ports (1-16) for Rx MP-A
|
|
default values are 1 1 16384 32768 16 16
|
|
The MP-A may be disabled by default at build time if the MMC driver byte mode patch
|
|
is not available in kernel.
|
|
|
|
Examples:
|
|
iwpriv mlan0 mpactrl : Get MP aggregation parameters
|
|
iwpriv mlan0 mpactrl 0 0
|
|
: Disable MP aggregation for Tx, Rx respectively
|
|
iwpriv mlan0 mpactrl 1 1 8192 8192 8 8
|
|
: Enable MP aggregation for Tx, Rx
|
|
: Set Tx, Rx buffer size to 8192 bytes
|
|
: Set maximum Tx, Rx ports to 8
|
|
|
|
deepsleep
|
|
This command is used to set/get auto deep sleep mode.
|
|
|
|
Usage:
|
|
iwpriv mlanX deepsleep [n] [m]
|
|
|
|
where the parameters are:
|
|
[n]: Enable/disable auto deep sleep mode (1/0)
|
|
[m]: Idle time in milliseconds after which firmware will put the device
|
|
in deep sleep mode. Default value is 100 ms.
|
|
|
|
Examples:
|
|
iwpriv mlan0 deepsleep : Display auto deep sleep mode
|
|
iwpriv mlan0 deepsleep 1 : Enable auto deep sleep mode, idle time unchanged
|
|
iwpriv mlan0 deepsleep 0 : Disable auto deep sleep mode
|
|
iwpriv mlan0 deepsleep 1 500 : Enable auto deep sleep mode with idle time 500 ms
|
|
Note:
|
|
Deepsleep must be disabled before changing idle time.
|
|
|
|
usbsuspend
|
|
This command is used to put device to suspend mode.
|
|
Note: It's only valid on kernel 2.6.24 or later.
|
|
|
|
usbresume
|
|
This command is used to resume the device from suspend mode.
|
|
Note: It's only valid on kernel 2.6.24 or later.
|
|
|
|
hscfg
|
|
This command is used to configure the host sleep parameters.
|
|
|
|
Usage:
|
|
iwpriv mlanX hscfg [condition [[GPIO# [gap]]]]
|
|
|
|
This command takes one (condition), two (condition and GPIO#) or three
|
|
(condition, GPIO# and gap) parameters for set. If no parameter provided,
|
|
get is performed.
|
|
|
|
where Condition is:
|
|
bit 0 = 1 -- broadcast data
|
|
bit 1 = 1 -- unicast data
|
|
bit 2 = 1 -- mac event
|
|
bit 3 = 1 -- multicast data
|
|
bit 6 = 1 -- Wakeup when mgmt frame received.
|
|
bit 7 = 1 -- Reserved
|
|
bit 8 = 1 -- Disable non maskable data wakeup.
|
|
|
|
The host sleep mode will be canceled if condition is set to -1. The default is 0x7.
|
|
|
|
where GPIO is the pin number of GPIO used to wakeup the host. It could be any valid
|
|
GPIO pin# (e.g. 0-7) or 0xff (interface, e.g. SDIO will be used instead).
|
|
The default is 0xff.
|
|
|
|
where Gap is the gap in milliseconds between wakeup signal and wakeup event or 0xff
|
|
for special setting (host acknowledge required) when GPIO is used to wakeup host.
|
|
The default is 200.
|
|
|
|
The host sleep set except for cancellation will be blocked if host sleep is
|
|
already activated.
|
|
|
|
Please note hssetpara and usbsuspend/usbresume commands should be used for USB
|
|
host sleep related tests.
|
|
|
|
Examples:
|
|
iwpriv mlan0 hscfg : Get current host sleep mode
|
|
iwpriv mlan0 hscfg -1 : Cancel host sleep mode
|
|
iwpriv mlan0 hscfg 3 : Broadcast and unicast data
|
|
Use GPIO and gap set previously
|
|
iwpriv mlan0 hscfg 2 3 : Unicast data
|
|
Use GPIO 3 and gap set previously
|
|
iwpriv mlan0 hscfg 2 1 0xa0 : Unicast data
|
|
Use GPIO 1 and gap 160 ms
|
|
iwpriv mlan0 hscfg 2 0xff : Unicast data
|
|
Use interface (e.g. SDIO)
|
|
Use gap set previously
|
|
iwpriv mlan0 hscfg 4 3 0xff : MAC event
|
|
Use GPIO 3
|
|
Special host sleep mode
|
|
iwpriv mlan0 hscfg 1 0xff 0xff : Broadcast data
|
|
Use interface (e.g. SDIO)
|
|
Use gap 255ms
|
|
|
|
hssetpara
|
|
This command is used to set host sleep parameters.
|
|
|
|
Usage:
|
|
iwpriv mlanX hssetpara Condition [GPIO# [gap]]
|
|
|
|
Note:
|
|
1) The usages of parameters are the same as "hscfg" command.
|
|
2) The parameters will be saved in the driver and be used when host suspends.
|
|
|
|
deauth
|
|
This command is used to send a de-authentication to an arbitrary AP.
|
|
If [n] is omitted, the driver will deauth the associated AP.
|
|
If in ad-hoc mode this command is used to stop beacon transmission
|
|
from the station and go into idle state.
|
|
|
|
When <n> is supplied as a MAC address, the driver will deauth the
|
|
specified AP. If the AP address matches the driver's associated AP,
|
|
the driver will disconnect. Otherwise, the driver remains connected.
|
|
|
|
radioctrl
|
|
This command is used to turn on/off the radio.
|
|
Note: The radio can be disabled only in disconnected state.
|
|
|
|
where value of n is:
|
|
0 -- Disable
|
|
1 -- Enable
|
|
|
|
Examples:
|
|
iwpriv mlan0 radioctrl 1 : Turn the radio on
|
|
iwpriv mlan0 radioctrl : Get radio status
|
|
|
|
reassoctrl
|
|
This command is used to turn on/off re-association in driver.
|
|
|
|
Usage:
|
|
iwpriv mlanX reassoctrl [n]
|
|
|
|
Where value of n is:
|
|
0 -- Disable
|
|
1 -- Enable
|
|
|
|
Examples:
|
|
iwpriv mlan0 reassoctrl : Get re-association status
|
|
iwpriv mlan0 reassoctrl 1 : Turn re-association on
|
|
|
|
bandcfg
|
|
This command is used to set/get infra/ad-hoc band.
|
|
Note: This command is only available in disconnected state.
|
|
|
|
Usage:
|
|
iwpriv mlanX bandcfg [l] [m] [n]
|
|
|
|
where the parameters:
|
|
[l]: Infrastructure band
|
|
bit 0: B
|
|
bit 1: G
|
|
bit 2: A
|
|
bit 3: GN
|
|
bit 4: AN
|
|
|
|
bit 5: AC 2.4G
|
|
bit 6: AC 5G
|
|
[m]: Ad-hoc start band
|
|
bit 0: B
|
|
bit 1: G
|
|
bit 2: A
|