Updated firmware:
SDIO-UART W8987 Firmware version 16.92.21.p76.2
PCIE-UART W8997 Firmware version 16.92.21.p76.2
SDIO-UART W8997 Firmware version 16.92.21.p76.2
SDIO-UART IW416 Firmware version 16.92.21.p76.3
SDIO_UART IW612 Firmware version 18.99.1.p154.40
SDIO-UART W8801 Firmware version 14.92.36.p180
SDIO-UART W9098 Firmware version 17.92.1.p136.24
PCIE-UART W9098 Firmware version 17.92.1.p136.24
WLAN new Additions/Removals/Improvements:
---------------
1. SD8987: WSFD-443: Clock synch feature
WLAN Bug Fixes:
---------------
1. SD8987/PCIE8997/IW416: WSW-24682: Ping is failing between testbed STA and STAUT after GTK rekey from AP
2. SD8987/PCIE8997/IW416: WSW-23252: Carrier sense test on Japanese regulation fail
3. SD8987: WSW-24668: STAUT is sending unprotected BTM/WNM action frames
4. SD8987: WSW-24629: Add support for antenna diversity control using gpio
5. SD8987: WSFD-658: Annex 106 - GPIO based FEM control via SOC register programming
6. SD8987: WSW-23926: UDP RX is lower than 5Mbps when playing music in shielding room
7. SD8987: WSW-22542: WiFi hang up with diff command timeout during run BT Inband/outband IR test w/ WiFi activities
8. SD8987/IW416: WSFD-653: Enable AES in FW by default
9. SD8987: WSW-23252 WSW-24023 Fix for probe resp and beacon leak
10. SD8987: WSFD-494: WiFi won't be connected back immediately when screen is off
11. PCIE8997: WSW-23539: Disconnection with reason 15 during WPA re-keying
12. PCIE8997: WSW-23252 WSW-24023: Fix for probe resp and beacon leak
13. IW416: WSW-23771: WLAN deauthentication observed if A2DP suspended and started again
14. IW416: WSW-23957: MMHAP Unable make connection with NXP Reference Devices
15. IW612: WSW-23908: Observing device hang issue when doing channel switch for MMH with open security
16. IW612: WSW-24518: 100% chload sometimes if EDMAC is enabled and any STA is connected
17. IW612: WCSWREL-413: P2P cannot work with the latest firmware
18. PCIE9098/SD9098: WCSWREL-414: P2P cannot work and observe command timeout
19. PCIE9098: Wakeup card timeout after suspend/resume
20. PCIE9098/SD9098: WSFD-599: Support trigger frame generating in RF test mode
BT/Co-ex Bug Fixes:
-------------------
1. SD8987: WSW-22599: Audio glitch could be heard when ACL is Master role(BT only scenario) in Congestion environment
2. IW416: WSW-23661: LE power capping to 10 dBm needs to be revoked for silicon supporting BT 5.0 and higher versions
3. IW416: WSW-24502: Audio is not heard in TX direction during incoming/outgoing NBS call with Ref device
4. IW416: WSW-21498: Heavy A2DP Audio Distortion (Glitch in every ~1sec) observed when DUT is at 5 meter distance from reference device
5. IW416: WSW-22879: 2nd BT(S) link failed to establish in the presence of SCO/eSCO connection on the first(M) link
6. IW416: WSW-19213: After starting BT/BLE Tx, Tx response is observed momentarily on litepoint
7. IW416: WSW-24321: "Unknown HCI Command " returned as status for cmd "3f fc 00" to enable Independent Reset via in-Band
8. IW416: WSW-25052: FW not getting up after enabling Independent Reset via in-Band
9. IW416: WSW-24024: Wlan De-authentication Observed while STA/MMH+LE Scan Coex Scenario
10. IW416: WSW-24825: DUT not responding to the pair/connect request sent by the reference device
11. PCIE8997: WSW-24482: Random mute pattern observed during A2DP_SRC streaming with Ref1 when OPP_TX started with Ref2
12. PCIE8997: WSW-18190: Issue observed in BT Paging /LE Connection + MMH/STA[BGN20] with Wifi RX traffic
13. IW612: WSW-23062: Speaker Disconnection while switching A2DP streaming between two speakers
14. IW612: WSW-23992: Frequent Page timeout (0x04) observed in DUT for Create_Connection command in scatternet scenarios
15. IW612: WSW-24302: Severe A2DP glitches are observed while connecting disconnecting A2DP-SNK devices
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Updated firmware:
SDIO-UART W8987 Firmware version 16.92.21.p76
PCIE-UART W8997 Firmware version 16.92.21.p76
SDIO-UART W8997 Firmware version 16.92.21.p76
SDIO-UART IW416 Firmware version 16.92.21.p76
SDIO_UART IW612 Firmware version 18.99.1.p154.18
Unchanged firmware:
SDIO-UART W8801 Firmware version 14.92.36.p178
SDIO-UART W9098 Firmware version 17.92.1.p136.13
PCIE-UART W9098 Firmware version 17.92.1.p136.13
WLAN new Additions/Removals/Improvements:
---------------
1. SD8987/IW416: WiFi Agile Multi-Band
2. SD8987: Monitor Mode
3. SD8987/IW416: uAPSD / PPS
4. SD8987: Packet Coalescing
5. SD8987/IW416: Support Boot Sleep Patch
6. PCIE8997/SD8997/IW416: Enable Wifi Easy Connect (DPP)
7. PCIE8997/SD8997: Wi-Fi Enhanced Open (OWE)
8. PCIE8997/SD8997/IW416: WPA3 embedded
9. PCIE8997/SD8997/IW416: mDNS (Bonjour) Offload - Wi-Fi
10. PCIE8997/SD8997/IW416: IPv6 NS Offload
11. PCIE8997/SD8997/IW416: Auto Reconnect
12. PCIE8997/SD8997: Independent reset via inband
13. PCIE8997/SD8997: Enable Independent Reset via Out-of-Band
WLAN Bug Fixes:
---------------
1. SD8987: WSW-23818: Fixed the DFS channel failure
2. SD8997: WSW-23254: auto_tx Feature fails with seconds interval configuration
3. SD8997: WSW-19809: less TP observed in P2P- 11AC/AN/BGN, TCP/UDP, TX/RX
4. IW612: WSW-23423: WLAN+BT Parallel download and Combo FW download consuming more current compared to BT+WLAN
5. IW612: WSW-21650: False radar detection when IW620 transmitting
6. IW612: WSW-22003: Low throughput was observed in 2.4G-Tx when Netgear AP 20/40 MHz coexistence was enabled
BT/COEX New Additions/Removals/Improvements:
-------------------
1. SD8987/PCIE8997/SD8997: BT/BLE Deepsleep
2. PCIE8997: Wake on BLE
3. IW416: BLE Multi-Adv / Advertisement Extension
4. IW416: LE Long Range
BT/Co-ex Bug Fixes:
-------------------
1. SD8987: WSW-23234: BREDR qualification TCs failure
2. SD8987: WSW-23233: BLE qualification TCs failures
3. SD8987: WSW-21475: Only one headset can hear the voice after establish two esco links during DUAL HFP test
4. SD8987: WSW-23110: Pairing failure when connecting with nRF connect app from mobile phone
5. SD8987: WSW-22242: Sometimes BT firmware is downloaded successfully, but cannot active and WIFI scan command will timeout
6. PCIE8997/SD8997: WSW-19165: New BREDR TCs and failures with TCRL2021-1 and TCRL2021-2
7. PCIE8997/SD8997: WSW-19166: New BLE TCs and failures with TCRL2021-1 and TCRL2021-2
8. PCIE8997/SD8997: WSW-20158: Disconnection with reason 15 during WPA re-keying
9. PCIE8997/SD8997: WSW-21809: Both OPP & HFP links drop when DUT starts OPP-TX transfer
10. IW416: WSW-22293: BluetoothLeAdvertiserTest cases fails during CTS run
11. IW416: WSW-19098: New BREDR TCs and failures with TCRL2021-2, E17535
12. IW416: WSW-19164: New BLE TCs and failures with TCRL2021-2, E17535
13. IW416: WSW-22605: DUT displaying wrong LMP Version i.e 5.0 instead of 5.3
14. IW612: WSW-23431: DUT hangs during execute LL TCs ,hard to continue the Qual testing
15. IW612: WSW-21751: No eSCO connection complete event after remote device reject eSCO connection
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Updated firmware:
PCIE-UART W8997 Firmware version 16.92.21.p55.3
SDIO-UART W8997 Firmware version 16.92.21.p55.3
SDIO-UART IW416 Firmware version 16.92.21.p55.3
Unchanged firmware:
SDIO-UART W8987 Firmware version 16.92.21.p41.4
SDIO-UART W9098 Firmware version 17.92.1.p116.1
PCIE-UART W9098 Firmware version 17.92.1.p116.1
SDIO-UART W8801 Firmware version 14.92.36.p174
WLAN Bug Fixes:
---------------
1. PCIE8997/SD8997/IW416: WCSWREL-368/WSW-21865: STA side WoWLAN Test fails as Host is not waking up after unicast ping
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Updated firmware:
PCIE-UART W8997 Firmware version 16.92.21.p55.2
SDIO-UART W8997 Firmware version 16.92.21.p55.2
SDIO-UART IW416 Firmware version 16.92.21.p55.1
SDIO-UART W8987 Firmware version 16.92.21.p41.4
Unchanged firmware:
SDIO-UART W9098 Firmware version 17.92.1.p116.1
PCIE-UART W9098 Firmware version 17.92.1.p116.1
SDIO-UART W8801 Firmware version 14.92.36.p174
WLAN Bug Fixes:
---------------
1. PCIE8997/SD8997: WSW-21404: Support for SSID field in neighbor request command is not present
2. PCIE8997/SD8997: WSW-19887: WPA3-R3 1st SAE commit (M1) not able to succeed
3. PCIE8997/SD8997: WSW-21196: P2P client disconnect with P2P GO when In-STA connecting to Ex-AP with different P2P GO channel
4. PCIE8997/SD8997: WSW-20725: In-STA don't send association request while setting pscfg DTIM interval from 1 to 3
5. PCIE8997/SD8997: WSW-20061: Duplicate HT/VHT IE seen in beacon of P2P GO
6. IW416: WSW-21196: P2P client disconnect with P2P GO when In-STA connecting to Ex-AP with different P2P GO channel
7. IW416: WSW-20061: Duplicate HT/VHT IE seen in beacon of P2P GO
8. IW416: WSW-19335: RSN Extension IE is not included in Assoc req when AP side does not connect via WPA3 R3
9. IW416: WSW-20788: Radar Detection Probability is below 60% for all ETSI
10. IW416: WSW-21404: Support for SSID field in neighbor request command is not present
11. IW416: WSW-11603: MMH fails to detect Radar signals in JP W56 Region
12. IW416: WSW-12993: DFS Support is required for New JP W53 Radar
13. IW416: WSW-19887: WPA3-R3 1st SAE commit (M1) not able to succeed
14. IW416: WSW-20725: In-STA don't send association request while setting pscfg DTIM interval from 1 to 3
BT/Co-ex Bug Fixes:
-------------------
1. PCIE8997/SD8997: WSW-20601: DUT hang observed after Severe A2DP Glitches and audio loss after launching invalid_max_slot exploiter
2. PCIE8997/SD8997: WSW-19719: LE advertising stopped unexpectedly
3. PCIE8997/SD8997: WSW-20971: DUT won't reply the received 2Mbps LLCP Date length Update Request and stop responding new RX pkt any longer
4. PCIE8997/SD8997: WSW-18231: Not able to get any packet received counts, RSSI, PER information for BT RX and packet received counts for BLE RX
5. SD8987: WSW-20157: DUT assigned same connection Handle to two different LE Remote Devices in dual mode
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Updated firmware:
PCIE-UART W8997 Firmware version 16.92.21.p55.1
SDIO-UART W8997 Firmware version 16.92.21.p55.1
SDIO-UART IW416 Firmware version 16.92.21.p55
Unchanged firmware:
SDIO-UART W9098 Firmware version 17.92.1.p116.1
PCIE-UART W9098 Firmware version 17.92.1.p116.1
SDIO-UART W8987 Firmware version 16.92.21.p41.3
SDIO-UART W8801 Firmware version 14.92.36.p174
WLAN new Additions/Removals/Improvements:
---------------
1. PCIE8997/SD8997: WSW-19003: 802.11z (Host based TDLS)
2. PCIE8997/SD8997: WSW-17793: Enable 802.11k and 802.11v
3. PCIE8997/SD8997: WSW-17801: Enable DFS (Radar Detection) Master
4. PCIE8997/SD8997: WSW-17809: Enable P2P for Miracast
5. PCIE8997/SD8997: WSW-19002: 802.11r (STA Roaming)
6. PCIE8997/SD8997: WSW-19007: Embedded Authenticator
7. PCIE8997/SD8997: WSW-19008: Embedded Supplicant
8. PCIE8997/SD8997: WSW-19015: Enable FIPS
9. IW416: WSW-19021: Enable 802.11k
10. IW416: WSW-19022: Enable 802.11v
11. IW416: WSW-19025: Enable DFS (Radar Detection) Master
12. IW416: WSW-19027: Embedded Authenticator
13. IW416: WSW-19028: Embedded Supplicant
14. IW416: WSW-19023: 802.11r (STA Roaming)
WLAN Bug Fixes:
---------------
1. PCIE8997: WSW-17438: Wake up card timeout occurs during OTT box power on
2. PCIE8997: WSW-18483: EU Cert needs to pass with Option A
3. PCIE8997: WSW-18347: 0x10d CMD Timeout occurs when In-STA connecting 2.4G Ex-AP or running TCP Tx iperf throughput while A2DP music is playing
4. PCIE8997: WSW-18236: Beamforming packets are not getting filtered in HT20 in CSI record
5. PCIE8997: WSW-18323: CSI records not captured on un-associate state
6. PCIE8997: WSW-18326: uAP bring-up on DFS in uAP+STA simultaneous mode
7. PCIE8997: WSW-18327: CAC starts on the MMH for DFS when STA on DFS channel in uAP+STA simultaneous mode
8. SD8997: WSW-19820: STA sends deauth to Ex-AP shortly after connection
9. SD8997: WSW-19858: STA reported link lost event shortly after connection
10. SD8997: WSW-19944: STA occurs auth timeout frequently while trying to connect to Ex-AP
11. SD8997: WSW-20060: AW-CM276MA-PUR 5G CH155 Rx sensitivity is less compared to 8997 MFG FW on antenna Aux port
12. SD8997: WSW-20118: Duplicate frame of HT Cap , VHT Cap, HT info and VHT info is present in Beacons
13. SD8997: WSW-20140: Deauth occurs during connecting to Ex-AP
14. SD8997: WSW-20277: STA occurs 0x107/0xd0 command timeout while doing security Fuzz testing
15. SD8997: WSW-20394: In-STA doesn't response Ex-AP's "Message 1 of 4" EAPOL frame until FW link lost occurs
16. IW416: WSW-17943: Failed to create uAP if ED MAC offset is set to 0x1C at 5G with HT40
17. IW416: WSW-18928: Suspend_Resume stress failed with error -16
18. IW416: WSW-19138: DUT is not able to re-associate with EX-AP with Android GUI automatically after removal of interference signal
19. IW416: WSW-19659: connection WPA2-EAP TTLS and WPA/WPA2-EAP TTLS FAILS but EAP -TLS Passing
20. IW416: WSW-19787: MMH fails to start in Channel 100
21. IW416: WSW-19807: IW416_Type1XK_64ch_RF performance issue with rf_test_mode
22. IW416: WSW-19970: Data/Beacon Frame leakage seen after application of interference signal in 2G for both STA/MMH Mode
BT/COEX New Additions/Removals/Improvements:
-------------------
1. PCIE8997/SD8997: WSW-19006: BCA Time Sharing Coex
2. PCIE8997/SD8997: WSW-19009: BLE Multi-Adv
3. IW416: WSW-19026: BCA Time Sharing Coex
4. IW416: WSW-19029: External Coex
BT/Co-ex Bug Fixes:
-------------------
1. PCIE8997: WSW-11660: LMP Response TO is observed after ref phone initiates disconnection of ACL after eSCO connection fails to establish
2. PCIE8997: WSW-15020: During MMH TCP_RX/UDP_RX traffic BT-HID_GW data gets stuck
3. PCIE8997: WSW-16791: Non-supported LE Features are still observed as supported as part of MM release
4. PCIE8997: WSW-16992: Link loss (Connection TO/LMP Response Timeout) is observed during the connection with iPhone 11/iPhone 12 Mini
5. PCIE8997: WSW-17440: low WLAN throughputs observed in lescan coex scenario
6. PCIE8997: WSW-17442: low WLAN throughputs observed in A2DP SRC and SINK coex scenario
7. PCIE8997: WSW-18272: OPP-Tx file transfer is failed during STA connected in 2.4GHz BGN-20
8. PCIE8997: WSW-18522: Audio is not heard in both Tx/Rx direction during incoming WBS call with iphone-12 mini
9. PCIE8997: WSW-19252: DUT hang observed after Severe A2DP Glitches and audio loss after launching "au_rand_flooding" exploiter
10. SD8997: WSW-18188: Low TP observed in OPP-TX + STA(HT20) with WLAN RX Traffic
11. SD8997: WSW-18189: Issue observed in BT Paging /LE Connection + MMH[BGN20] with Wifi RX traffic
12. SD8997: WSW-18197: 2M PHY value option is disabled with default libbluetooth.so file in the nrf app
13. SD8997: WSW-19794: Audio distortion observed in HFP call when OPP_Tx data transfer started
14. SD8997: WSW-19917: VTS test cases are getting fail when BLE wakeup host feature is enabled
15. SD8997: WSW-19939: OPP_Rx File transfer is not successful and once transfer unsuccessful, Bluetooth is turned off automatically
16. IW416: WSW-13709: A2DP_SRC Streaming got suspended automatically with Hardware Error
17. IW416: WSW-16791: Non-supported LE Features are still observed as supported as part of MM release
18. IW416: WSW-17191: Grant is de-asserted by IW416 before Request is de-asserted by K32W
19. IW416: WSW-19308: After Disconnection, Failed to reconnect Reference device through PAN profile from DUT
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Updated firmware:
SDIO-UART W9098 Firmware version 17.68.1.p116
SDIO-UART W8987 Firmware version 16.92.21.p41
SDIO-UART W8801 Firmware version 14.92.36.p174
SDIO-UART IW416 Firmware version 16.92.21.p41
PCIE-UART W9098 Firmware version 17.68.1.p116
SDIO-UART W8997 Firmware version 16.92.21.p41
Unchanged firmware:
PCIE-UART W8997 Firmware version 16.92.21.p26.1
WLAN Bug Fixes:
---------------
1. SD9098: WSW-17876: RF Test Mode: After Disabling cont_mode(CMD18_CW=1), Firmware is getting crashed if radio mode is changed
2. SD9098: WSW-9362: EU-CERT: COT and Channel Access Mechanism tests failing with OptionA Procedure
3. SD8987: WSW-18878: WPA2-PSK Roaming failed
4. SD8987: WSW-18865: VHT80 TCP-tx throughput only run about 170Mbps, both STA and MMH mode
5. SD8987: WSW-16412: Enable 2.4GHz 40MHz bandwidth support for V16 devices
6. SD8987: WSW-18454: Added 802.11k suppor
7. SD8987: WSW-18455: Added 802.11v support
8. SD8987: WSW-18456: Added 802.11r (STA Roaming) support
9. SD8987: WSW-18457: Added 802.11z (Host based TDLS) support
10. SD8987: WSW-18459: DFS (Radar Detection) Master support (some known issues in specific config are found, and under debugging)
11. SD8987: WSW-18461: Per-path regulatory power table (Tested only with RD Board)
12. SD8987: WSW-18462: Per-path DPD Calibration Front-end Loss (Tested only with RD Board)
13. SD8987: WSW-18463: Antenna diversity (Tested only with RD Board)
14. SD8801: WSW-16811: Fix scan cmd timeout issue
15. IW416: WSW-19214: get link layer statistic fail, CMD_RESP: cmd 0x256 error
16. IW416: WSW-16412: Enable 2.4GHz 40MHz bandwidth support for V16 deviceS
17. IW416: WSW-17096: Wi-Fi BGN(2.4Ghz) Association failure issue
18. IW416: WSW-17705: IW416 Wlan Spurious emission issue
19. IW416: WSW-17552: Channel Occupancy Time (COT) failure in STA mode. Max. COT for HT20/MCS0 in 5G mode should be < 6 ms, but observed value is 6.081 ms
20. PCIE9098: WSW-12608: Optimize moal driver loading via firmware init time optimization
21. PCIE9098: WSW-9362: EU-CERT: COT and Channel Access Mechanism tests failing with OptionA Procedure
22. SD8997: WSW-16427: Wi-Fi throughput drops to 0 during scan
23. SD8997: WSW-16819: Wi-Fi occurs 0xa4 command timeout with reason code 12 while playing online video about 16 hours
24. SD8997: WSW-17573: Android UI can't display Wi-Fi standard correctly
BT/Co-ex Bug Fixes:
-------------------
1. SD9098: WSW-17745: RF Test Mode: Not able to capture packets on IQXeL and Measure tx-power value is approx. -42dBm for configured power 4dBm for BLE
2. SD9098: WSW-17747: Not able to get any packet received counts, RSSI, PER information for BT RX
3. SD9098: WSW-18470: Deauthentication on MAC2 and further causing hang issue without ps_mode and auto_ds load parameters
4. SD8987: WSW-18517: 7-8 Glitches are observed during the A2DP SRC streaming + BT Inquiry
5. SD8987: WSW-18598: BT On/Off cycle fails with InBand IR
6. SD8987: Independent Reset via In-band for BT and Wi-Fi(NOTE: This feature needs separate BT Only and WLAN Only firmware binaries, which are provided in this release)
7. IW416: WSW-9978: BLE Qualification protocol failures
8. IW416: WSW-13613: eSCO connection is accepted with retransmission window 0x06
9. IW416: WSW-10265: More than expected channels getting blocked in case of STA + BT Internal AFH
10. PCIE9098: WSW-17745: RF Test Mode: Not able to capture packets on IQXeL and Measure tx-power value is approx. -42dBm for configured power 4dBm for BLE
11. PCIE9098: WSW-17747: Not able to get any packet received counts, RSSI, PER information for BT RX
12. SD8997: WSW-16022: Low 2.4GHz Wi-Fi throughput in Wi-Fi/A2DP Coex case when AP RSSI is weak
13. SD8997: WSW-16243: Hardware Error(0x23) occured during A2DP streaming
14. SD8997: WSW-17570: There is 8s+ delay in waking up OTT host from RCU after host enters into sleep
15. SD8997: WSW-16820: BLE_HID fails to Pair while performing HFP Skype call[Page Timeout: 20sec]
16. SD8997: WSW-18095: Low TP observed in STA(VHT80) WiFi RX Traffic in Coex scenario with INQUIRY/LE_SCAN/A2DP SRC
17. SD8997: WSW-17479: Google Voice Assistant can't be used
18. SD8997: WSW-19097: A2DP glitch in long distance test
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Firmware:
SDIO-UART W8801 Firmware version 14.92.36.p171
SDIO-UART IW416 Firmware version 16.92.21.p11.2
PCIE-UART W9098 Firmware version 17.92.5.p11
SDIO-UART W8997 Firmware version 16.92.10.p219.5
PCIE-UART W8997 Firmware version 16.92.10.p213.4
SDIO-UART W8987 Firmware version 16.92.21.p11.1
WLAN Bug Fixes:
---------------
1. PCIE8997: Fixed issue with 5G start when sae_pwe=1 is set
2. PCIE8997: Added WPA3 R3 Support
3. PCIE9098: Fixed issue with 5G start when sae_pwe=1 is set
4. PCIE9098: Added WPA3 R3 Support
5. SD8801: Fixed issue with 5G start when sae_pwe=1 is set
6. SD8801: Added WPA3 R3 Support
7. SD8987: Fixed issue with 5G start when sae_pwe=1 is set
8. SD8987: Addressed Ideal period probability cert test failure in MMH 5GHz HT20 mode
9. SD8987: Added FW and VHAL implementation for WoWLAN
10. SD8987: Added WPA3 R3 Support
11. SD8997: Fixed issue with 5G start when sae_pwe=1 is set
12. SD8997: Added WPA3 R3 Support
13. SDIW416: Fixed issue with 5G start when sae_pwe=1 is set
14. SDIW416: Addressed Ideal period probability cert test failure in MMH 5GHz HT20 mode
15. SDIW416: Added WPA3 R3 Support
BT Bug Fixes:
-------------
1. PCIE8997: Added an update to the 'Impersonation in the Passkey Entry Protocol' Vulnerability (original CVE-2020-26558)
2. PCIE8997: Added BT ANSSI VU fix
3. PCIE9098: Added an update to the 'Impersonation in the Passkey Entry Protocol' Vulnerability (original CVE-2020-26558)
4. PCIE9098: Added BT ANSSI VU fix
5. SD8987: Added an update to the 'Impersonation in the Passkey Entry Protocol' Vulnerability (original CVE-2020-26558)
6. SD8987: Fixed issue of Set Random Private Address Timeout Command accepting values more than 1 Hr
7. SD8987: Added BT ANSSI VU fix
8. SD8997: Added an update to the 'Impersonation in the Passkey Entry Protocol' Vulnerability (original CVE-2020-26558)
9. SD8997: Added BT ANSSI VU fix
10. SDIW416: Added an update to the 'Impersonation in the Passkey Entry Protocol' Vulnerability (original CVE-2020-26558)
11. SDIW416: Fixed issue of Set Random Private Address Timeout Command accepting values more than 1 Hr
12. SDIW416: Added BT ANSSI VU fix
13. SDIW416: More than expected channels getting blocked in case of STA + BT internal AFH
Yocto build, it requires to copy the files to:
- lib/firmware/nxp/
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Firmware:
SDIO-UART W8801 Firmware version 14.92.36.p170
SDIO-UART IW416 Firmware version 16.92.21.p11
PCIE-UART W9098 Firmware version 17.92.5.p10
SDIO-UART W8997 Firmware version 16.92.10.p219.4
PCIE-UART W8997 Firmware version 16.92.10.p213.3
SDIO-UART W8987 Firmware version 16.92.21.p11
WLAN Bug Fixes:
---------------
1. PCIE8997: Fixed pre-cert issue where STA is responding to the ARP requests after receiving encrypted M3 and reset PN from AP
2. PCIE8997: Added WFA SVD failure fixes
3. PCIE9098: Fixed pre-cert issue where STA is responding to the ARP requests after receiving encrypted M3 and reset PN from AP
4. PCIE9098: Added WFA SVD failure fixes
5. SD8801: Fixed low TCP RX throughput issue For Linksys 1900AC AP
6. SD8801: Corresponding firmware change for fixing low throughput issue in WPA3-SAE security
7. SD8801: Enabled ED-MAC by default
8. SD8801: Fixed low throughput in Rx A-MSDU
9. SD8801: Fixed low throughput issue in P2P GC
10. SD8801: Added WFA SVD failure fixes
11. SD8987: Added WFA SVD failure fixes
12. SD8987: Minor generic bug fixe
13. SD8987: Fixed RF test mode "Continuous Transmit Test" error happened on the second time test
14. SD8987: Fixed Low TCP-Tx and UDP-Tx throughput issues
15. SD8997: Fixed pre-cert issue where STA is responding to the ARP requests after receiving encrypted M3 and reset PN from AP
16. SD8997: Added WFA SVD failure fixes
17. SDIW416: Added WFA SVD failure fixes
18. SDIW416: Minor generic bug fixes
BT Bug Fixes:
-------------
1. SD8987: Minor generic bug fixe
2. SD8987: Fixed FW replying with different reason when the Host has rejected the incoming call
3. SD8987: Fixed Outgoing connection disconnection with reason "Connection terminated by local host" after pairing with reference device
4. SDIW416: Fixed an issue with retransmission window during eSCO connection accept
5. SDIW416: Continuous A2DP-SNK audio glitches issue observed in MMH Rx traffic
Yocto build, it requires to copy the files to:
- lib/firmware/nxp/
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Firmware:
SDIO-UART IW416 Firmware version 16.92.10.p233.2
PCIE-UART W9098 Firmware version 17.92.5.p9
SDIO-UART W8997 Firmware version 16.92.10.p219.2
PCIE-UART W8997 Firmware version 16.92.10.p213.2
SDIO-UART W8987 Firmware version 16.92.10.p210.1
WLAN Bug Fixes:
---------------
1. IW416: Fixed the issue of Channel Occupancy Time (COT) coming as 7.85 msec where as it should be under 6 msec
2. SDIO8997: Fixed issue of ping through gateway for some minutes when running long time test
3. SDIO8997: Added 2.4GHz 40MHz bandwidth support for V16 devices
4. PCIE8997: Fixed issue of ping through gateway for some minutes when running long time test
5. PCIE8997: Added 2.4GHz 40MHz bandwidth support for V16 devices
BT Bug Fixes:
-------------
1. IW416: Fixed the issue of DUT blocking more than 50/55 channels in shielded environment without any external noise
2. IW416: Fixed the issue of Continuous A2DP-SNK audio glitches in Rx traffic
3. PCIE9098: Fixed the scan on fail as Command Disallowed is observed for LE Set Extended Scan Parameters
4. SDIO8997: Hardware Error(0x23) occured during A2DP streaming
5. PCIE8997: Hardware Error(0x23) occured during A2DP streaming
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Firmware:
SDIO-UART IW416 Firmware version 16.92.10.p233.1
PCIE-UART W9098 Firmware version 17.92.5.p8
SDIO-UART W8997 Firmware version 16.92.10.p219.1
PCIE-UART W8997 Firmware version 16.92.10.p213.1
SDIO-UART W8987 Firmware version 16.92.10.p210.1
WLAN Bug Fixes:
---------------
1. IW416: [WCSWREL-100] L5.4.70: 2.4G AP connect fail after run 5G STA mode
2. IW416: Fixed BSS start/stop stress test failed with 0x10d cmd timeout
3. PCIE9098: Continuous association with 5 different APs stress fails
4. PCIE9098: DUT is unable to receive packets in MFG mode
5. PCIE9098: Command timeout 0x107 observed while running Tx UDP traffic to two stations with scan triggered for every 30s in background
6. SDIO8997: [WCSWREL-100] L5.4.70: 2.4G AP connect fail after run 5G STA mode
7. PCIE8997: [WCSWREL-100] L5.4.70: 2.4G AP connect fail after run 5G STA mode
8. SDIO8987: [WCSWREL-100] L5.4.70: 2.4G AP connect fail after run 5G STA mode
BT Bug Fixes:
-------------
1. IW416: Command tx timeout as soon as advertise on/off is done in a loop
2. IW416: Fixed the error "connection rejected due to security reasons" during lescan and file transfer
3. IW416: Fixed the Type1XK_Adaptivity failure
4. IW416: Fixed the LE link disconnection with "Connection Timeout"
5. IW416: Fixed the “Authentication Failure” issue found during BT E0/AES connection process
6. IW416: [WCSWREL-136]cannot hear voice from BT HFP call with IW416 on both imx8mq and imx8mp
7. IW416: Disable AES feature support due to known issue
8. PCIE9098: Disabled LE Extended ADV, periodic ADV & Channel Selection Algorithm
9. PCIE9098: Disable AES feature support due to known issue
10. SDIO8997: Fixed the low 2.4GHz Wi-Fi throughput in Wi-Fi/A2DP Coex case when AP RSSI is weak
11. SDIO8997: Fixed the Low TP ~400Kbps issue during STA_2.4GHz_A2DP_SRC/SNK_UDP_RX
12. SDIO8997: Disable AES feature support due to known issue
13. PCIE8997: Disable AES feature support due to known issue
14. SDIO8987: Fixed the Issue of Controller not sending "LE create connection" command into air
15. SDIO8987: [WCSWREL-147] Bluetooth will crash and restart fail in stress test
16. SDIO8987: Disable AES feature support due to known issue
Yocto build, it requires to copy the files to:
- lib/firmware/nxp/
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Firmware:
SDIO-UART IW416 Firmware version 16.92.10.p177
PCIE-UART W9098 Firmware version 17.92.5.p6
SDIO-UART W8997 Firmware version 16.92.10.p219
PCIE-UART W8997 Firmware version 16.92.10.p213
SDIO-UART W8987 Firmware version 16.92.10.p210
WLAN Bug Fixes:
---------------
1. PCIE9098: TCP Uplink Traffic Test on P2P-GO and BSS Start Stop stress fails within 1hour
2. PCIE9098: Suspend-Resume fails in connected state
3. PCIE9098: ED-Mac is not enabled by default
4. PCIE9098: EU-Cert is getting failed for 2.4G in mlan0 interface in STA mode
BT Bug Fixes:
-------------
1. SDIO8997: Low TP ~30Kbps is observed during [STA_2.4GHZ_A2DP_SRC/SNK_TCP_TX]
Yocto build, it requires to copy the files to:
- lib/firmware/nxp/
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Firmware:
PCIE-UART W9098 Firmware version 17.92.5.p1
SDIO-UART W8997 Firmware version 16.92.10.p216
PCIE-UART W8997 Firmware version 16.92.10.p212
SDIO-UART W8987 Firmware version 16.92.10.p209
WLAN Bug Fixes:
---------------
1. PCIE9098: Fixed issues seen during stress test with data traffic.
BT Bug Fixes:
-------------
None.
Yocto build, it requires to copy the files to:
- lib/firmware/nxp/
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Firmware:
PCIE-UART W9098 Firmware version 17.92.1.p55
SDIO-UART W8997 Firmware version 16.92.10.p156
PCIE-UART W8997 Firmware version 16.92.10.p212
SDIO-UART W8987 Firmware version 16.92.10.p209
WLAN Bug Fixes:
---------------
1. Added Wi-Fi VU fixes for four firmwares
2. PCIE9098: Fixed 11AX pre-cert/EU-cert test issues
3. PCIE9098: Fixed DFS channel switch compliance related issue
4. PCIE9098: Fixed WPA3 band switch issue
5. PCIE9098: Fixed issues related to scan stress
6. PCIE9098: Fixed issues seen during traffic stress test
7. SDIO8997: Fixed issues seen during traffic stress test
BT Bug Fixes:
-------------
1. PCIE9098: Fixed various issues related to device hang
2. PCIE9098: Fixed issues with BT mode switch
Yocto build, it requires to copy the files to:
- lib/firmware/nxp/
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Firmware:
PCIE-UART W8997 Firmware version 16.92.10.p211
PCIE-UART W9098 Firmware version 17.92.1.p46
SDIO-UART W8997 Firmware version 16.92.10.p150
WLAN Bug Fixes:
---------------
1. Fixed an issue where wakeup card timeout is seen when STAUT connects
to Ext-AP
2. Added multiple fixes for 11ax pre-cert issues
3. Added RF Test Mode support
4. Added fixes for scan command timeout seen during stress tests
5. Added fixes for 11ac pre-cert failures
BT Bug Fixes:
-------------
1. Fixed an issue where BT restart is observed
2. Fixed issues where A2DP gliches are observed when connecting a
second phone
3. Ported multiple BT fixes for stability
Yocto build, it requires to copy the files to:
- lib/firmware/nxp/
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
