Updated firmware:
SDIO-UART W9098 Firmware version 17.68.1.p116
SDIO-UART W8987 Firmware version 16.92.21.p41
SDIO-UART W8801 Firmware version 14.92.36.p174
SDIO-UART IW416 Firmware version 16.92.21.p41
PCIE-UART W9098 Firmware version 17.68.1.p116
SDIO-UART W8997 Firmware version 16.92.21.p41
Unchanged firmware:
PCIE-UART W8997 Firmware version 16.92.21.p26.1
WLAN Bug Fixes:
---------------
1. SD9098: WSW-17876: RF Test Mode: After Disabling cont_mode(CMD18_CW=1), Firmware is getting crashed if radio mode is changed
2. SD9098: WSW-9362: EU-CERT: COT and Channel Access Mechanism tests failing with OptionA Procedure
3. SD8987: WSW-18878: WPA2-PSK Roaming failed
4. SD8987: WSW-18865: VHT80 TCP-tx throughput only run about 170Mbps, both STA and MMH mode
5. SD8987: WSW-16412: Enable 2.4GHz 40MHz bandwidth support for V16 devices
6. SD8987: WSW-18454: Added 802.11k suppor
7. SD8987: WSW-18455: Added 802.11v support
8. SD8987: WSW-18456: Added 802.11r (STA Roaming) support
9. SD8987: WSW-18457: Added 802.11z (Host based TDLS) support
10. SD8987: WSW-18459: DFS (Radar Detection) Master support (some known issues in specific config are found, and under debugging)
11. SD8987: WSW-18461: Per-path regulatory power table (Tested only with RD Board)
12. SD8987: WSW-18462: Per-path DPD Calibration Front-end Loss (Tested only with RD Board)
13. SD8987: WSW-18463: Antenna diversity (Tested only with RD Board)
14. SD8801: WSW-16811: Fix scan cmd timeout issue
15. IW416: WSW-19214: get link layer statistic fail, CMD_RESP: cmd 0x256 error
16. IW416: WSW-16412: Enable 2.4GHz 40MHz bandwidth support for V16 deviceS
17. IW416: WSW-17096: Wi-Fi BGN(2.4Ghz) Association failure issue
18. IW416: WSW-17705: IW416 Wlan Spurious emission issue
19. IW416: WSW-17552: Channel Occupancy Time (COT) failure in STA mode. Max. COT for HT20/MCS0 in 5G mode should be < 6 ms, but observed value is 6.081 ms
20. PCIE9098: WSW-12608: Optimize moal driver loading via firmware init time optimization
21. PCIE9098: WSW-9362: EU-CERT: COT and Channel Access Mechanism tests failing with OptionA Procedure
22. SD8997: WSW-16427: Wi-Fi throughput drops to 0 during scan
23. SD8997: WSW-16819: Wi-Fi occurs 0xa4 command timeout with reason code 12 while playing online video about 16 hours
24. SD8997: WSW-17573: Android UI can't display Wi-Fi standard correctly
BT/Co-ex Bug Fixes:
-------------------
1. SD9098: WSW-17745: RF Test Mode: Not able to capture packets on IQXeL and Measure tx-power value is approx. -42dBm for configured power 4dBm for BLE
2. SD9098: WSW-17747: Not able to get any packet received counts, RSSI, PER information for BT RX
3. SD9098: WSW-18470: Deauthentication on MAC2 and further causing hang issue without ps_mode and auto_ds load parameters
4. SD8987: WSW-18517: 7-8 Glitches are observed during the A2DP SRC streaming + BT Inquiry
5. SD8987: WSW-18598: BT On/Off cycle fails with InBand IR
6. SD8987: Independent Reset via In-band for BT and Wi-Fi(NOTE: This feature needs separate BT Only and WLAN Only firmware binaries, which are provided in this release)
7. IW416: WSW-9978: BLE Qualification protocol failures
8. IW416: WSW-13613: eSCO connection is accepted with retransmission window 0x06
9. IW416: WSW-10265: More than expected channels getting blocked in case of STA + BT Internal AFH
10. PCIE9098: WSW-17745: RF Test Mode: Not able to capture packets on IQXeL and Measure tx-power value is approx. -42dBm for configured power 4dBm for BLE
11. PCIE9098: WSW-17747: Not able to get any packet received counts, RSSI, PER information for BT RX
12. SD8997: WSW-16022: Low 2.4GHz Wi-Fi throughput in Wi-Fi/A2DP Coex case when AP RSSI is weak
13. SD8997: WSW-16243: Hardware Error(0x23) occured during A2DP streaming
14. SD8997: WSW-17570: There is 8s+ delay in waking up OTT host from RCU after host enters into sleep
15. SD8997: WSW-16820: BLE_HID fails to Pair while performing HFP Skype call[Page Timeout: 20sec]
16. SD8997: WSW-18095: Low TP observed in STA(VHT80) WiFi RX Traffic in Coex scenario with INQUIRY/LE_SCAN/A2DP SRC
17. SD8997: WSW-17479: Google Voice Assistant can't be used
18. SD8997: WSW-19097: A2DP glitch in long distance test
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Updated firmware:
SDIO-UART W9098 Firmware version 17.92.1.p98.1
PCIE-UART W8997 Firmware version 16.92.21.p26.1
SDIO-UART W8987 Firmware version 16.92.21.p26
Unchanged firmware:
SDIO-UART W8801 Firmware version 14.92.36.p171
SDIO-UART IW416 Firmware version 16.92.21.p11.2
PCIE-UART W9098 Firmware version 17.92.5.p11
SDIO-UART W8997 Firmware version 16.92.10.p219.5
WLAN Bug Fixes:
---------------
1. SD9098: WSW-17752: [RF-Test Mode]: for "wlan_set_rf_tx_frame"(CMD35), Measured spectrum BW remains 20MHz even when configured BW is 40/80MHz
2. SD9098: WSW-17538: STAUT is not sending SA Query Response to AP's correctly protected SA Query Request
3. SD9098: WSW-17754: "wlan_set_rf_tx_frame"(CMD35), Not able to receive any packets on IQXeL for HE-SU MCS10 & MCS 11 1ss and 2ss data rates
4. SD9098: WSW-18149: Fix for default 2G TxPwrTbl does not show 8dBm for all mod indices
5. SD9098: WSW-14255: DUT goes into hang state during re-association by changing channel/restarting Ex-AP
6. SD9098: WSW-14386: TCP Uplink Traffic on P2P-GO and BSS Start Stop fails after 3hours; Timeout cmd id 0x0
7. SD9098: WSW-11201: Host Wakeup for Management Frames in AP Mode fails, when APUT configured with "mgmtfilter"
8. SD9098: WSW-14213: TCP/UDP Bidirectional traffic test does not sustain more than 3 hours
9. SD9098: WSW-14215: TCP Uplink stress fails with dump within 3hours duration
10. SD9098: WSW-14459: TCP/UDP Bidirectional traffic test does not sustain more than 10mins; cmd53 error is seen
11. SD9098: WSW-14594: uap0 is unable send traffic with all Fixrate LTF+GI combinations
12. SD9098: WSW-15600: Country IE is seen in beacon, even after disabling 80211d option in hostapd file
13. SD9098: WSW-17616: Default tx-power values (8dBm) are changing to some random values for different rate ID’s after starting hostapd
14. PCIE8997: WSW-16427: Fixed issue of Wi-Fi throughput drops to 0 during scan
15. PCIE8997: WSW-16819: Fixed issue of 0xa4 command timeout with reason code 12 while playing online video about 16 hours
16. PCIE8997: WSW-17568: Fixed issue of "Ext scan enh timeout" occurs after connect to IPv6 network for a long time
17. PCIE8997: WSW-17573: Fixed issue of Android UI not displaying Wi-Fi standard correctl
18. PCIE8997: WSW-17613: 0x107 command timeout occurs while playing online video based on IPv6 network for a long time
19. PCIE8997: WSW-17657: In-STA auto disconnects from Ex-AP in standby and is unable to reconnect Ex-AP
20. SD8987: WSW-17426: rf test mode: 5G Tx EVM/SPECTRUM MASK failed on CH64 and CH100 with mass market release
21: SD8987: WSW-17577: RF test mode bandwidth 40MHz not working with 2.4G band
22. SD8987: WSFD-386: FW and VHAL Implementation for WOWLAN
23. SD8987: WSW-15035: Fixed WiFi scan event timeout happen during run WiFi scan and BT connect-disconnect cycle test simultaneously sometimes
24. SD8987: WSW-16212: Fixed fw init fail with 0xf007 when independent reset and STA keep connection
25. SD8987: WSW-17450: Fixed the issue of android.net.wifi.cts.WifiManagerTest failure
BT/Co-ex Bug Fixes:
-------------
1. SD9098: WSW-17662: Fixed the issue of Link Loss(Connection Timeout) during LE Connectio
2. SD9098: WSW-17667: Wlan Deauthentication is observed with A2DP Source + STA[HT20] with DUT ACL Role both Slave and Master
3. SD9098: WSW-17619: Authentication Failure is observed when try to connect with DUT after Power on/off
4. SD9098: WSW-17887: During encryption process if host send remote version request, sometimes link is getting disconnected with LMP/LL timeout
5. SD9098: WSW-17982: After making call, Synchronous Connect Complete returns with status Unsupported LMP Parameter Value / Unsupported LL Parameter Value (0x20)
6. SD9098: WSW-17249: Random DUT hang observed after receiving directed advertisements while doing le scan
7. SD9098: WSW-16606: Low BT Tx/Rx/Bi-Directional TP on BT(M/S) for 1/3/5 Slot packet type
8. SD9098: WSW-13135: Throughput Drops abruptly in OPP_Tx to 8/16KBps from 64KBps when OPP_Tx is operating and simultaneously TCP_RX is running
9. PCIE8997: WSW-17982: After making call, Synchronous Connect Complete returns with status Unsupported LMP Parameter Value / Unsupported LL Parameter Value (0x20)
10. PCIE8997: WSW-17383: Request to enable Multi ADV feature to pass GTV Certification
11. PCIE8997: WSW-17479: Fixed issue of Google Voice Assistant usage
12. PCIE8997: WSW-17570: Fixed issue of 8s+ delay in waking up OTT host from RCU after host enters into sleep
13. PCIE8997: WSW-16306: Fixed issue of Low BT Tx/Rx throughput observed for all packet types in shielded environment
14. PCIE8997: WSW-18095: Fixed issue of Low TP observed in STA(VHT80) WiFi RX Traffic in Coex scenario with INQUIRY/LE_SCAN/A2DP SRC
15. SD8987: WSW-16820: BLE_HID fails to Pair while performing HFP Skype call
16. SD8987: WSW-16922: PTS Flouride Certification got failure for HSP/AG/IAC/BV-01-I
17. SD8987: WSW-16422: Set Random Private Address Timeout Command is accepting values more than 1 Hr
18. SD8987: WSW-16780: Bad and distorted voice quality can be heard from remote phone if we do connect and disconnect test with headset no matter incoming or outgoing call
19. SD8987: WSW-16924: Ctlr H/w error event showed when connect with Pixel Buds Version2
20. SD8987: WSW-15505: Heavy A2DP glitches can be heard in the noisy ENV if take speaker ~10meter away from UUT
21. SD8987: WSW-17237: LE_APCF_Command received from BT stack, 8987 return as dis-allowed
22. SD8987: WSW-16266: BLE devices failed to be connected during BT activities like HFP active call
23. SD8987: WSW-17034: No BT inquiry result found during PS4 gamepad pair/unpair test with A2DP streaming and BLE RC connected
24. SD8987: WSW-17423: Voice not hearable from both headset and phone sides when make the HFP call with NBS mode
25. SD8987: WSW-17476: Random A2DP glitches can be heard during A2DP playing with PixelBuds headset in the Noisy ENV
26. SD8987: WSW-16170: Read By Group Type Response is not being sent by the DUT due to collision between Public key request
27. SD8987: WSW-16438: WiFi hang up with command timeout(0x24) during running BT OOB IR or A2DP stress test and wifi do activity
28. SD8987: WSW-15570: A2DP glitch with wifi connected and do scan or Traffic running in noisy when testing A2DP+STA and A2DP+BLE RC+STA
29. SD8987: WSW-17664: BLE Fast Pair Doesnt Work as per expectation
30. SD8987: WSW-17325: DUT does not respond to POLL packets send by Remote Device due to which Connection terminates with "Connection timeout"
31. SD8987: WSW-17256: LE Create Connection with use white list for 2nd link is connected with wrong BD address
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Firmware:
SDIO-UART W8801 Firmware version 14.92.36.p171
SDIO-UART IW416 Firmware version 16.92.21.p11.2
PCIE-UART W9098 Firmware version 17.92.5.p11
SDIO-UART W8997 Firmware version 16.92.10.p219.5
PCIE-UART W8997 Firmware version 16.92.21.p17
SDIO-UART W8987 Firmware version 16.92.21.p11.1
SDIO-UART W9098 Firmware version 17.92.1.p91
WLAN Bug Fixes:
---------------
1. SD9098: New Release
2. PCIE8997: WSW-13725 COT and Channel Access Mechanism tests need to pass with OptionA Procedure
3. PCIE8997: WSW-16784 Fix data path stuck issue in WMM disabled case
4. PCIE8997: WSW-15054 Fix 5G fail to start when sae_pwe=1 issue
5. PCIE8997: WSFD-386 FW and VHAL Implementation for WOWLAN
6. PCIE8997: WSW-11784 STAUT sends more than 1 MPDU in AMPDU even though tx win restricted to 1, with SCBT AP
7. PCIE8997: WSW-16378 Scan event timeout with 0x20 cmd timeout, when run connect extAP with different security overnight stress
8. PCIE8997: WSW-16296 STAUT is responding to the ARP requests after receiving encrypted M3 and reset PN from AP
9. PCIE8997: WSW-16620 wlan_wakeup_card_timeout_func: ps_state=3 when run WiFi activities from GUI along with BT activitie
10. PCIE8997: WSW-16270 Enable DFS parameter to detect RADAR
11. PCIE8997: WSW-16602 FW timeout when switch conect with 2 AP with driver debug log enable
12. PCIE8997: WSW-16417 0x107/0x10d command timeout when switching AP security between WPA-PSK and open
13. PCIE8997: WSW-16207 0x10d command timeout when switching AP Security between open and WPA2-PSK
14. PCIE8997: WSW-12415 "Authentication Failure" happens during pair use AES method
15. PCIE8997: WSW-16126 Disable Aggr for MCS datarates < 30Mbps
16. PCIE8997: WSW-7275 Sometimes Ex-STA fails to get DHCP during conenct/disconnect loop
17. PCIE8997: WSW-13477 Fix chanAttrTbl chan num issue
18. PCIE8997: WSW-14259 Fix AMSDU size report issue in uAP mode
19. PCIE8997: WSW-11977 [11AC][TC-4.2.20]-Mismatch in WMMIE Parameter count observed in beacon and association response when configured as APUT
20. PCIE8997: WSW-13487 [HT40 HT Forty MHz Intolerant is set makes Throughput low in uAP mode]
21. PCIE8997: WSW-12207 Fix the issue that DUT follows AP's advertised Power Constraint
22. PCIE8997: WSW-15390 [RB3, RB3+, KF2][FP92] Re-enable 2G 40MHz support
BT/Co-ex Bug Fixes:
-------------
1. SD9098: New Release
2. PCIE8997: WSW-17423 Voice not hearable from both headset and phone sides when make the HFP call with NBS mode.Fail rate 100%
3. PCIE8997: WSW-16266 BLE HID devices failed to be connected during BT activities, Fail rate:70%
4. PCIE8997: WSW-16869 Observed DUT hang issue with two eSCO links
5. PCIE8997: WSW-16243 Hardware Error(0x23) occured during A2DP streaming
6. PCIE8997: WSW-13676 A2DP_SRC Streaming got suspended automatically with Hardware Error when BT Inquiry was running in the Background
7. PCIE8997: WSW-13965 [KF2][IMX8M.Linux][P2P-GC_BGN-20]Low WLAN TP is observed during A2DP_SRC
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Firmware:
SDIO-UART W8801 Firmware version 14.92.36.p171
SDIO-UART IW416 Firmware version 16.92.21.p11.2
PCIE-UART W9098 Firmware version 17.92.5.p11
SDIO-UART W8997 Firmware version 16.92.10.p219.5
PCIE-UART W8997 Firmware version 16.92.10.p213.4
SDIO-UART W8987 Firmware version 16.92.21.p11.1
WLAN Bug Fixes:
---------------
1. PCIE8997: Fixed issue with 5G start when sae_pwe=1 is set
2. PCIE8997: Added WPA3 R3 Support
3. PCIE9098: Fixed issue with 5G start when sae_pwe=1 is set
4. PCIE9098: Added WPA3 R3 Support
5. SD8801: Fixed issue with 5G start when sae_pwe=1 is set
6. SD8801: Added WPA3 R3 Support
7. SD8987: Fixed issue with 5G start when sae_pwe=1 is set
8. SD8987: Addressed Ideal period probability cert test failure in MMH 5GHz HT20 mode
9. SD8987: Added FW and VHAL implementation for WoWLAN
10. SD8987: Added WPA3 R3 Support
11. SD8997: Fixed issue with 5G start when sae_pwe=1 is set
12. SD8997: Added WPA3 R3 Support
13. SDIW416: Fixed issue with 5G start when sae_pwe=1 is set
14. SDIW416: Addressed Ideal period probability cert test failure in MMH 5GHz HT20 mode
15. SDIW416: Added WPA3 R3 Support
BT Bug Fixes:
-------------
1. PCIE8997: Added an update to the 'Impersonation in the Passkey Entry Protocol' Vulnerability (original CVE-2020-26558)
2. PCIE8997: Added BT ANSSI VU fix
3. PCIE9098: Added an update to the 'Impersonation in the Passkey Entry Protocol' Vulnerability (original CVE-2020-26558)
4. PCIE9098: Added BT ANSSI VU fix
5. SD8987: Added an update to the 'Impersonation in the Passkey Entry Protocol' Vulnerability (original CVE-2020-26558)
6. SD8987: Fixed issue of Set Random Private Address Timeout Command accepting values more than 1 Hr
7. SD8987: Added BT ANSSI VU fix
8. SD8997: Added an update to the 'Impersonation in the Passkey Entry Protocol' Vulnerability (original CVE-2020-26558)
9. SD8997: Added BT ANSSI VU fix
10. SDIW416: Added an update to the 'Impersonation in the Passkey Entry Protocol' Vulnerability (original CVE-2020-26558)
11. SDIW416: Fixed issue of Set Random Private Address Timeout Command accepting values more than 1 Hr
12. SDIW416: Added BT ANSSI VU fix
13. SDIW416: More than expected channels getting blocked in case of STA + BT internal AFH
Yocto build, it requires to copy the files to:
- lib/firmware/nxp/
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
from BSP conf
FwImage: update firmware to mxm5x17283
FwImage: wifi_mod_para.conf: change the load parameters of wifi
driver to support WPA3 feature
also refine load params to better align with WCS team.
Still keep wfd_name=p2p and max_vir_bss=1 to better support p2p
function.
Also add SD8801 load parameters support.
Signed-off-by: yang.tian <yang.tian@nxp.com>
As WCS team suggested, to keep align with them, need to remove the
wfd_name setting.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Approved-by: Tian Yang <yang.tian@nxp.com>
Firmware:
SDIO-UART W8801 Firmware version 14.92.36.p170
SDIO-UART IW416 Firmware version 16.92.21.p11
PCIE-UART W9098 Firmware version 17.92.5.p10
SDIO-UART W8997 Firmware version 16.92.10.p219.4
PCIE-UART W8997 Firmware version 16.92.10.p213.3
SDIO-UART W8987 Firmware version 16.92.21.p11
WLAN Bug Fixes:
---------------
1. PCIE8997: Fixed pre-cert issue where STA is responding to the ARP requests after receiving encrypted M3 and reset PN from AP
2. PCIE8997: Added WFA SVD failure fixes
3. PCIE9098: Fixed pre-cert issue where STA is responding to the ARP requests after receiving encrypted M3 and reset PN from AP
4. PCIE9098: Added WFA SVD failure fixes
5. SD8801: Fixed low TCP RX throughput issue For Linksys 1900AC AP
6. SD8801: Corresponding firmware change for fixing low throughput issue in WPA3-SAE security
7. SD8801: Enabled ED-MAC by default
8. SD8801: Fixed low throughput in Rx A-MSDU
9. SD8801: Fixed low throughput issue in P2P GC
10. SD8801: Added WFA SVD failure fixes
11. SD8987: Added WFA SVD failure fixes
12. SD8987: Minor generic bug fixe
13. SD8987: Fixed RF test mode "Continuous Transmit Test" error happened on the second time test
14. SD8987: Fixed Low TCP-Tx and UDP-Tx throughput issues
15. SD8997: Fixed pre-cert issue where STA is responding to the ARP requests after receiving encrypted M3 and reset PN from AP
16. SD8997: Added WFA SVD failure fixes
17. SDIW416: Added WFA SVD failure fixes
18. SDIW416: Minor generic bug fixes
BT Bug Fixes:
-------------
1. SD8987: Minor generic bug fixe
2. SD8987: Fixed FW replying with different reason when the Host has rejected the incoming call
3. SD8987: Fixed Outgoing connection disconnection with reason "Connection terminated by local host" after pairing with reference device
4. SDIW416: Fixed an issue with retransmission window during eSCO connection accept
5. SDIW416: Continuous A2DP-SNK audio glitches issue observed in MMH Rx traffic
Yocto build, it requires to copy the files to:
- lib/firmware/nxp/
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Change the wifi driver load parameters to support WPA3 feature, also to
better align with WCS team.
Still keep wfd_name=p2p and max_vir_bss=1 to better support p2p function.
Also add SD8801 load parameters support.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Approved-by: Tian Yang <yang.tian@nxp.com>
Firmware:
SDIO-UART IW416 Firmware version 16.92.10.p233.2
PCIE-UART W9098 Firmware version 17.92.5.p9
SDIO-UART W8997 Firmware version 16.92.10.p219.2
PCIE-UART W8997 Firmware version 16.92.10.p213.2
SDIO-UART W8987 Firmware version 16.92.10.p210.1
WLAN Bug Fixes:
---------------
1. IW416: Fixed the issue of Channel Occupancy Time (COT) coming as 7.85 msec where as it should be under 6 msec
2. SDIO8997: Fixed issue of ping through gateway for some minutes when running long time test
3. SDIO8997: Added 2.4GHz 40MHz bandwidth support for V16 devices
4. PCIE8997: Fixed issue of ping through gateway for some minutes when running long time test
5. PCIE8997: Added 2.4GHz 40MHz bandwidth support for V16 devices
BT Bug Fixes:
-------------
1. IW416: Fixed the issue of DUT blocking more than 50/55 channels in shielded environment without any external noise
2. IW416: Fixed the issue of Continuous A2DP-SNK audio glitches in Rx traffic
3. PCIE9098: Fixed the scan on fail as Command Disallowed is observed for LE Set Extended Scan Parameters
4. SDIO8997: Hardware Error(0x23) occured during A2DP streaming
5. PCIE8997: Hardware Error(0x23) occured during A2DP streaming
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Firmware:
SDIO-UART IW416 Firmware version 16.92.10.p233.1
PCIE-UART W9098 Firmware version 17.92.5.p8
SDIO-UART W8997 Firmware version 16.92.10.p219.1
PCIE-UART W8997 Firmware version 16.92.10.p213.1
SDIO-UART W8987 Firmware version 16.92.10.p210.1
WLAN Bug Fixes:
---------------
1. IW416: [WCSWREL-100] L5.4.70: 2.4G AP connect fail after run 5G STA mode
2. IW416: Fixed BSS start/stop stress test failed with 0x10d cmd timeout
3. PCIE9098: Continuous association with 5 different APs stress fails
4. PCIE9098: DUT is unable to receive packets in MFG mode
5. PCIE9098: Command timeout 0x107 observed while running Tx UDP traffic to two stations with scan triggered for every 30s in background
6. SDIO8997: [WCSWREL-100] L5.4.70: 2.4G AP connect fail after run 5G STA mode
7. PCIE8997: [WCSWREL-100] L5.4.70: 2.4G AP connect fail after run 5G STA mode
8. SDIO8987: [WCSWREL-100] L5.4.70: 2.4G AP connect fail after run 5G STA mode
BT Bug Fixes:
-------------
1. IW416: Command tx timeout as soon as advertise on/off is done in a loop
2. IW416: Fixed the error "connection rejected due to security reasons" during lescan and file transfer
3. IW416: Fixed the Type1XK_Adaptivity failure
4. IW416: Fixed the LE link disconnection with "Connection Timeout"
5. IW416: Fixed the “Authentication Failure” issue found during BT E0/AES connection process
6. IW416: [WCSWREL-136]cannot hear voice from BT HFP call with IW416 on both imx8mq and imx8mp
7. IW416: Disable AES feature support due to known issue
8. PCIE9098: Disabled LE Extended ADV, periodic ADV & Channel Selection Algorithm
9. PCIE9098: Disable AES feature support due to known issue
10. SDIO8997: Fixed the low 2.4GHz Wi-Fi throughput in Wi-Fi/A2DP Coex case when AP RSSI is weak
11. SDIO8997: Fixed the Low TP ~400Kbps issue during STA_2.4GHz_A2DP_SRC/SNK_UDP_RX
12. SDIO8997: Disable AES feature support due to known issue
13. PCIE8997: Disable AES feature support due to known issue
14. SDIO8987: Fixed the Issue of Controller not sending "LE create connection" command into air
15. SDIO8987: [WCSWREL-147] Bluetooth will crash and restart fail in stress test
16. SDIO8987: Disable AES feature support due to known issue
Yocto build, it requires to copy the files to:
- lib/firmware/nxp/
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Update Android wifi_mod_para.conf to
add SD9098 and SD8978 module wifi config,
and also update SD8997 and PCIE9098 wifi
module config.
Signed-off-by: yang.tian <yang.tian@nxp.com>
Firmware:
SDIO-UART IW416 Firmware version 16.92.10.p177
PCIE-UART W9098 Firmware version 17.92.5.p6
SDIO-UART W8997 Firmware version 16.92.10.p219
PCIE-UART W8997 Firmware version 16.92.10.p213
SDIO-UART W8987 Firmware version 16.92.10.p210
WLAN Bug Fixes:
---------------
1. PCIE9098: TCP Uplink Traffic Test on P2P-GO and BSS Start Stop stress fails within 1hour
2. PCIE9098: Suspend-Resume fails in connected state
3. PCIE9098: ED-Mac is not enabled by default
4. PCIE9098: EU-Cert is getting failed for 2.4G in mlan0 interface in STA mode
BT Bug Fixes:
-------------
1. SDIO8997: Low TP ~30Kbps is observed during [STA_2.4GHZ_A2DP_SRC/SNK_TCP_TX]
Yocto build, it requires to copy the files to:
- lib/firmware/nxp/
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Firmware:
PCIE-UART W9098 Firmware version 17.92.5.p1
SDIO-UART W8997 Firmware version 16.92.10.p216
PCIE-UART W8997 Firmware version 16.92.10.p212
SDIO-UART W8987 Firmware version 16.92.10.p209
WLAN Bug Fixes:
---------------
1. PCIE9098: Fixed issues seen during stress test with data traffic.
BT Bug Fixes:
-------------
None.
Yocto build, it requires to copy the files to:
- lib/firmware/nxp/
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Firmware:
PCIE-UART W9098 Firmware version 17.92.1.p55
SDIO-UART W8997 Firmware version 16.92.10.p156
PCIE-UART W8997 Firmware version 16.92.10.p212
SDIO-UART W8987 Firmware version 16.92.10.p209
WLAN Bug Fixes:
---------------
1. Added Wi-Fi VU fixes for four firmwares
2. PCIE9098: Fixed 11AX pre-cert/EU-cert test issues
3. PCIE9098: Fixed DFS channel switch compliance related issue
4. PCIE9098: Fixed WPA3 band switch issue
5. PCIE9098: Fixed issues related to scan stress
6. PCIE9098: Fixed issues seen during traffic stress test
7. SDIO8997: Fixed issues seen during traffic stress test
BT Bug Fixes:
-------------
1. PCIE9098: Fixed various issues related to device hang
2. PCIE9098: Fixed issues with BT mode switch
Yocto build, it requires to copy the files to:
- lib/firmware/nxp/
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Firmware:
PCIE-UART W8997 Firmware version 16.92.10.p211
PCIE-UART W9098 Firmware version 17.92.1.p46
SDIO-UART W8997 Firmware version 16.92.10.p150
WLAN Bug Fixes:
---------------
1. Fixed an issue where wakeup card timeout is seen when STAUT connects
to Ext-AP
2. Added multiple fixes for 11ax pre-cert issues
3. Added RF Test Mode support
4. Added fixes for scan command timeout seen during stress tests
5. Added fixes for 11ac pre-cert failures
BT Bug Fixes:
-------------
1. Fixed an issue where BT restart is observed
2. Fixed issues where A2DP gliches are observed when connecting a
second phone
3. Ported multiple BT fixes for stability
Yocto build, it requires to copy the files to:
- lib/firmware/nxp/
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Add file wifi_mod_para_powersave.conf which include
powersave_enable flag. Add logic in wifi driver which
can parse this flag.
Add append_bootargs:
setenv append_bootargs moal.mod_para=wifi_mod_para_powersave.conf
saveenv
Change-Id: If0875510385219e47f9b74c4b64b11701849db6c
Signed-off-by: zhipeng.wang <zhipeng.wang_1@nxp.com>
Firmware:
PCIE-UART W8997 Firmware version 16.92.10.p126
WLAN Bug Fixes:
---------------
1. Fix uAP start issue on switching bands
2. Fixed WLAN Link loss during UDP Rx + BT Inquiry, and WLAN deauth
during BT HFP coex scenarios
BT Bug Fixes:
-------------
1. Added fix to handle processing of SSR command to unblock command
queuing which was causing BT restart
Yocto build, it requires to copy the files to:
- lib/firmware/nxp/
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Firmware:
PCIE-UART W8997 Firmware version 16.92.10.p118
WLAN Bug Fixes:
---------------
1. Fixed VHT compressed beamforming frame related pre-cert issues
2. Corresponding firmware change for fixing WPA3 SAE pre-cert requirement
3. Fixed issue with scan logic where firmware was aborting complete scan
even if noise is detected on a different channel
4. Updated scan gap logic to prevent the DUT from missing ECSA IE beacons
5. Test Mode fix: Fixed path B Tx power issue for continuous wave mode
BT Bug Fixes:
-------------
1. Added fixes for A2DP glitches in various scnearios
2. Added change of disabling ping as AES is disabled.
This was causing LMP response timeout issue
3. Added changes to correctly handle WAR flag name to enable fix for
negative test cases involving LE connection.
Coex Bug Fixes:
-------------
1. Added fix for A2DP Glitches during coex scenarious
2. Added fix for BLE HID links losses
3. Added WLAN throughput improvements during BT device discovery scenarious
Yocto build, it requires to copy the files to:
- lib/firmware/nxp/
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Firmware:
PCIE-UART W8997 Firmware version 16.92.10.p113
Yocto build, it requires to copy the files to:
- lib/firmware/nxp/
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Firmware:
PCIE-UART W8997 Firmware version 16.92.10.p110
SDIO-UART W8987 Firmware version 16.92.10.p208
Yocto build, it requires to copy the files to:
- lib/firmware/nxp/
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
The 88w8987 firmware version: SDIO_WLAN_UART_BT_8987_16.92.10.p207_16.92.10.p207
The firmware is merged from the repo:
ssh://git@bitbucket.sw.nxp.com/wcswrel/
rel-NXP-WIFI-FP92-BT-FP92-LINUX-ANDROID-MXM4X17186.p7-MGPL.git
Firmware version 16.92.10.p207
Firmware updates:
WLAN Bug Fixes:
===============
1. Fixed WLAN hang issue which was observed during HFP + STA scenario during TCP Tx
BT Bug Fixes:
=============
1. Corrected feature bit advertising to disable AES completely,
which was causing pairing / connection failure
2. For PHY, if asymmetric traffic is used, then corrected the
handling to post error code as per spec
Yocto build, it requires to copy the files to:
- lib/firmware/nxp/sdiouart8987_combo_v0.bin
- lib/firmware/nxp/wifi_mod_para_sd8987.conf
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
The 88w8987 firmware version: SDIO_WLAN_UART_BT_8987_16.92.10.p206_16.92.10.p206
The firmware is merged from the repo:
ssh://git@bitbucket.sw.nxp.com/wcswrel/
rel-NXP-WIFI-FP92-BT-FP92-LINUX-ANDROID-MXM4X17186.p6-MGPL.git
Firmware version 16.92.10.p206
Firmware updates:
WLAN Bug Fixes:
===============
1. Fixed WLAN link loss which was observed in MMH scenario some time
after inquiry was started
2. Test Mode: Fixed cw mode power delta issue which was seen in configured
Vs measured Tx power value as part of this command
BT Bug Fixes:
=============
1. Fixed the issue of A2DP link loss that was observed due to
connection timeout (0x08)
Yocto build, it requires to copy the files to:
- lib/firmware/nxp/sdiouart8987_combo_v0.bin
- lib/firmware/nxp/wifi_mod_para_sd8987.conf
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
The 88w8987 firmware version: SDIO_WLAN_UART_BT_8987_16.92.10.p204_16.92.10.p204
The firmware is merged from the repo:
ssh://git@bitbucket.sw.nxp.com/wcswrel/
rel-NXP-WIFI-FP92-BT-FP92-LINUX-ANDROID-MXM4X17186.p4-MGPL.git
Firmware updates:
New Additions:
==============
1. Update Tx continuous mode logic for test mode
WLAN Bug Fixes:
===============
1. Fixed WLAN deauth which was observed during wlan traffic in presence
of BT Inquiry, Inquiry scan or Paging on android console
2. Fixed issue of P2P Group Owner not sending QoS Null Frame to Station
3. Solved the issue while reconnecting to AP after channel switch in 5GHz
band for 40MHz/80MHz channel bandwidth
4. Addressed the issue for Roaming from AP1 to AP2 which was failing
using wpa_cli roam command in 5GHz band for 40MHz/80MHz channel bandwidth
BT Bug Fixes:
=============
1. Invalid / garbage data was observed in Test mode during BT RF testing
2. Made changes to set default PCM configuration settings in firmare
3. Disabled CS2 and Adv Ext features for MM release
4. BLE qualification related fixes
5. Fixed issue where controller was giving incorrect error code,
Corrected the error code per spec
6. Added fix of setting correct values for default parameter length when
DLE (Data Length Extension) is enabled with LR (Long Range) disabled
7. Added change to restrict Wesco to 4 for single slot EV packets
Yocto build, it requires to copy the files to:
- lib/firmware/nxp/sdiouart8987_combo_v0.bin
- lib/firmware/nxp/wifi_mod_para_sd8987.conf
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
The 88w8987 firmware version: SDIO_WLAN_UART_BT_8987_16.92.10.p202_16.92.10.p202
The firmware is merged from the repo:
ssh://git@bitbucket.sw.nxp.com/wcswrel/
rel-nxp-wifi-fp92-bt-fp92-linux-android-mxm4x17186.p2-mgpl.git
Yocto build, it requires to copy the files to:
- lib/firmware/nxp/sdiouart8987_combo_v0.bin
- lib/firmware/nxp/wifi_mod_para_sd8987.conf
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
The 88w8987 firmware version: SDIO_WLAN_UART_BT_8987_16.92.10.p99_16.85.10.p99
The firmware is merged from the repo:
ssh://git@bitbucket.sw.nxp.com/wcswrel/
rel-nxp-wifi-fp92-bt-fp85-linux-android-mxm4x17186-mgpl.git
Yocto build, it requires to copy the files to:
- lib/firmware/nxp/sdiouart8987_combo_v0.bin
- lib/firmware/nxp/wifi_mod_para_sd8987.conf
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
The 88w8987 firmware version: SDIO_WLAN_UART_BT_8987_16.92.10.p80_16.85.10.p80
The firmware is merged from the repo:
ssh://git@bitbucket.sw.nxp.com/wcswrel/
rel-nxp-wifi-fp92-bt-fp85-linux-android-mxm4x17175-mgpl.git
Yocto build, it requires to copy the files to:
- lib/firmware/nxp/sdiouart8987_combo_v0.bin
- lib/firmware/nxp/wifi_mod_para_sd8987.conf
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
The 88w8987 firmware version: SDIO_WLAN_UART_BT_8987_16.92.10.p73
The firmware is merged from the repo:
ssh://git@bitbucket.sw.nxp.com/wcswrel/
rel-nxp-wifi-fp92-bt-fp85-linux-android-mxm4x17169-gpl.git
Yocto build, it requires to copy the files to:
- lib/firmware/nxp/sdiouart8987_combo_v0.bin
- lib/firmware/nxp/wifi_mod_para_sd8987.conf
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Firmware: BCM4356/2 wl0: Aug 29 2019 02:05:27
version 7.35.180.197 (r722171 CY) FWID 01-4c8512f9
Note:
From Cypress 'Kenneth Ma' confirm, the firmware version
already fix the security issue: KR00K - CVE-2019-15126
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
update 1FD_CYW4356 firmware version to:
Firmware version = wl0: Feb 13 2019 02:16:44 version 7.35.180.194
(r709573 CY) FWID 01-b055fb9
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
update 1FD_CYW4359 firmware version to:
Firmware version = wl0: Feb 20 2019 18:05:52 version 9.40.109
(r710128 CY) FWID 01-848095d2
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
update 1MW_CYW43455 firmware version to:
Firmware version = wl0: Mar 3 2019 19:47:25 version 7.45.184
(r712131 CY) FWID 01-b363c0a0
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
