=============================================================================== U S E R M A N U A L Copyright (C) 2008-2019, Marvell International Ltd. All Rights Reserved 1) FOR DRIVER BUILD Goto source code directory wlan_src/. make [clean] build The driver and utility binaries can be found in ../bin_xxxx directory. The driver code supports Linux kernel up to 5.0.9. 2) FOR DRIVER INSTALL a) Copy firmware image pcie8897_uapsta.bin | ... to /lib/firmware/mrvl/ directory, create the directory if it doesn't exist. b) Install WLAN driver There are drv_mode, max_sta_bss, max_uap_bss etc. module parameters. The bit settings of drv_mode are, Bit 0 : STA Bit 1 : uAP Bit 2 : WIFIDIRECT Bit 4 : NAN max_sta_bss: Maximum number of STA BSS (default 1, max 1) sta_name: Name of the STA interface (default: "mlan") max_uap_bss: Maximum number of uAP BSS (default 1, max 2) uap_name: Name of the uAP interface (default: "uap") uap_max_sta: Maximum number of STA for UAP/GO (default 0, max 10) max_wfd_bss: Maximum number of WIFIDIRECT BSS (default 1, max 1) wfd_name: Name of the WIFIDIRECT interface (default: "wfd") max_vir_bss: Number of Virtual interfaces (default 0) nan_name: Name of the NAN interface (default: "nan") max_nan_bss: Number of NAN interfaces (default 1) For example, to install PCIE8897 driver, insmod mlan.ko insmod pcie8897.ko [drv_mode=3] [fw_name=mrvl/pcie8897_uapsta.bin] To load driver in STA only mode, insmod mlan.ko insmod pcie8897.ko drv_mode=1 [fw_name=mrvl/pcie8897_uapsta.bin] To load driver in uAP only mode, insmod mlan.ko insmod pcie8897.ko drv_mode=2 [fw_name=mrvl/pcie8897_uapsta.bin] To switch mode between STA only, uAP only and uAPSTA in run time, echo drv_mode=1 > /proc/mwlan/config // STA mode echo drv_mode=2 > /proc/mwlan/config // uAP mode echo drv_mode=3 > /proc/mwlan/config // uAPSTA mode c) Uninstall WLAN driver, ifconfig mlanX down ifconfig uapX down rmmod pcie8xxx rmmod mlan Use mfg_mode = 1: To load driver with MFG firmware file, when insmod WLAN driver and specify MFG firmware name if needed. This option loads default normal FW on HW reset (reset button is pressed on the board). Use mfg_mode = 2: To load driver with MFG firmware file, when insmod WLAN driver and specify MFG firmware name if needed. This option reloads previously specifed MFG firmware only on HW reset. There are some other parameters for debugging purpose etc. Use modinfo to check details. drvdbg= dev_cap_mask= mac_addr=xx:xx:xx:xx:xx:xx auto_ds=0|1|2 ps_mode=0|1|2 p2p_enh=0|1 max_tx_buf=2048|4096|8192 cfg_11d=0|1|2 dts_enable=0|1 hw_test=0|1 fw_serial=0|1 req_fw_nowait=0|1 init_cfg= e.g. copy init_cfg.conf to firmware directory, init_cfg=mrvl/init_cfg.conf cal_data_cfg= e.g. copy cal_data.conf to firmware directory, cal_data_cfg=mrvl/cal_data.conf txpwrlimit_cfg= e.g. copy txpwrlimit_cfg_set.conf to firmware directory, txpwrlimit_cfg=mrvl/txpwrlimit_cfg_set.conf init_hostcmd_cfg= e.g. copy init_hostcmd_cfg.conf to firmware directory, init_hostcmd_cfg=mrvl/init_hostcmd_cfg.conf cfg80211_wext= Bit 0: STA WEXT Bit 1: uAP WEXT Bit 2: STA CFG80211 Bit 3: uAP CFG80211 cfg80211_drcs=1|0 reg_alpha2= wq_sched_prio: Priority for work queue wq_sched_policy: Scheduling policy for work queue (0: SCHED_NORMAL, 1: SCHED_FIFO, 2: SCHED_RR, 3: SCHED_BATCH, 5: SCHED_IDLE) Please note that, both wq_sched_prio and wq_sched_policy should be provided as module parameters. If wq_sched_policy is (0, 3 or 5), then wq_sched_prio must be 0. wq_sched_prio should be 1 to 99 otherwise. rx_work=0|1|2 indrstcfg=<2-byte IR configuration> gpio pin (high byte): GPIO pin no to be used as trigger for out band reset (0xFF: default pin configuration) ir_mode (low byte) : independent reset mode (0: disable, 1: enable out band, 2: enable in band) For example, to enable out band reset via gpio_pin 14 indrstcfg=0x0e01 To enable out band reset via default gpio_pin indrstcfg=0xff01 To enable in band reset and disable out band reset indrstcfg=0x02 Note: On some platforms (e.g. PXA910/920) double quotation marks ("") need to used for module parameters. insmod sd8xxx.ko " ..." 3) FOR DRIVER PROC & DEBUG The following info are provided in /proc/net/mwlan/mlanX/info, on kernel 2.6.24 or later, the entry is /proc/mwlan/mlanX/info. driver_name = "wlan" driver_version = interface_name = "mlanX" bss_mode = "Ad-hoc" | "Managed" | "Auto" | "Unknown" media_state = "Disconnected" | "Connected" mac_address = <6-byte adapter MAC address> multicase_count = essid = bssid = channel = region_code = multicast_address[n] = num_tx_bytes = num_rx_bytes = num_tx_pkts = num_rx_pkts = num_tx_pkts_dropped = num_rx_pkts_dropped = num_tx_pkts_err = num_rx_pkts_err = carrier "on" | "off" tx queue "stopped" | "started" The following debug info are provided in /proc/net/mwlan/mlanX/debug, on kernel 2.6.24 or later, the entry is /proc/mwlan/mlanX/debug. drvdbg = wmm_ac_vo = wmm_ac_vi = wmm_ac_be = wmm_ac_bk = max_tx_buf_size = tx_buf_size = curr_tx_buf_size = ps_mode = <0/1, CAM mode/PS mode> ps_state = <0/1/2/3, awake state/pre-sleep state/sleep-confirm state/sleep state> is_deep_sleep = <0/1, not deep sleep state/deep sleep state> wakeup_dev_req = <0/1, wakeup device not required/required> wakeup_tries = hs_configured = <0/1, host sleep not configured/configured> hs_activated = <0/1, extended host sleep not activated/activated> tx_pkts_queued = pps_uapsd_mode = <0/1, PPS/UAPSD mode disabled/enabled> sleep_pd = qos_cfg = tx_lock_flag = <0/1, Tx lock flag> port_open = <0/1, port open flag> scan_processing = <0/1, scan processing flag> num_tx_timeout = num_cmd_timeout = timeout_cmd_id = timeout_cmd_act = last_cmd_id = last_cmd_act = last_cmd_index = <0 based last command index> last_cmd_resp_id = last_cmd_resp_index = <0 based last command response index> last_event = last_event_index = <0 based last event index> num_cmd_h2c_fail = num_cmd_sleep_cfm_fail = num_tx_h2c_fail = num_evt_deauth = num_evt_disassoc = num_evt_link_lost = num_cmd_deauth = num_cmd_assoc_ok = num_cmd_assoc_fail = cmd_sent = <0/1, send command resources available/sending command to device> data_sent = <0/1, send data resources available/sending data to device> txbd_rdptr = txbd_wrptr = rxbd_rdptr = rxbd_wrptr = eventbd_rdptr = eventbd_wrptr = cmd_resp_received = <0/1, no cmd response to process/response received and yet to process> event_received = <0/1, no event to process/event received and yet to process> ioctl_pending = tx_pending = rx_pending = lock_count = malloc_count = mbufalloc_count = malloc_cons_count = main_state = Use dmesg or cat /var/log/debug to check driver debug messages. To log driver debug messages to file, a) Edit /etc/syslog.conf, add one line "*.debug /var/log/debug" on kernel 2.6.24 or later, edit /etc/rsyslog.conf instead b) touch /var/log/debug (if the file doesn't exist) c) service syslog restart on kernel 2.6.24 or later, service rsyslog restart Update /proc/sys/kernel/printk to change message log levels. For example, echo 6 > /proc/sys/kernel/printk (messages with a higher priority than 6 will be printed to the console) echo 15 > /proc/sys/kernel/printk (all messages will be printed to console) 4) FOR IWPRIV COMMAND NAME This manual describes the usage of private commands used in Marvell MLAN Linux Driver. To use parameters as hex format, a '0x' must precede it for the parameters to be parsed properly. SYNOPSIS iwpriv [sub-command] ... iwpriv mlanX version iwpriv mlanX verext iwpriv mlanX getsignal [m] [n] iwpriv mlanX antcfg [m] [n] iwpriv mlanX regioncode [n] iwpriv mlanX cfpcode [m] [n] iwpriv mlanX wwscfg [m] iwpriv mlanX esuppmode iwpriv mlanX passphrase iwpriv mlanX httxcfg [] [] iwpriv mlanX htcapinfo [] [] iwpriv mlanX addbapara

iwpriv mlanX aggrpriotbl iwpriv mlanX addbareject iwpriv mlanX txbufcfg iwpriv mlanX amsduaggrctrl iwpriv mlanX httxbfcap [cap] iwpriv mlanX httxbfcfg "[;GlobalData/tsData/interval/txPeerData/snrData]" iwpriv mlanX deepsleep [n] [m] iwpriv mlanX hscfg [condition [[GPIO# [gap]]]] iwpriv mlanX hssetpara condition [GPIO# [gap]] iwpriv mlanX deauth [n] iwpriv mlanX radioctrl iwpriv mlanX reassoctrl [n] iwpriv mlanX bandcfg [l] [m] [n] iwpriv mlanX getlog iwpriv mlanX 11dcfg iwpriv mlanX 11dclrtbl iwpriv mlanX wmmcfg [n] iwpriv mlanX txpowercfg [ [ [ ]]] iwpriv mlanX qoscfg iwpriv mlanX getdatarate iwpriv mlanX txratecfg [n] iwpriv mlanX bcninterval [n] iwpriv mlanX sysclock [clk1] [clk2] [clk3] [clk4] iwpriv mlanX drvdbg [n] iwpriv mlanX mgmtframectrl iwpriv mlanX warmreset iwpriv mlanX regrdwr [value] iwpriv mlanX rdeeprom iwpriv mlanX memrdwr

[value] iwpriv mlanX inactivityto [k] iwpriv mlanX scancfg [t] [m] [p] [s] [a] [b] [ext] iwpriv mlanX sleeppd [n] iwpriv mlanX pscfg [k] [d] [l] ... iwpriv mlanX fwwakeupmethod [n] [g] iwpriv mlanX associate " " iwpriv mlanX sleepparams [ ] iwpriv mlanX netmon [ [ [offset]]] iwpriv mlanX authtype [n] iwpriv mlanX powercons [n] iwpriv mlanX htstreamcfg [n] iwpriv mlanX ipaddr [";"] iwpriv mlanX macctrl [n] iwpriv mlanX dfstesting [ ] iwpriv mlanX indrstcfg [gpio_pin] DESCRIPTION Those commands are used to send additional commands to the Marvell MLAN card via the Linux device driver. The mlanX parameter specifies the network device that is to be used to perform this command on. It could be mlan0, mlan1 etc. version This is used to get the current version of the driver and the firmware. verext Retrieve and display an extended version string from the firmware Usage: iwpriv mlanX verext [#] where [#] is an optional argument to retrieve a specific version string, omission of the argument retrieves the 0 indexed string. getsignal This command gets the last and average value of RSSI, SNR and NF of Beacon and Data. Note: This command is available only when STA is connected. where value of m is: 1 -- RSSI (Receive Signal Strength Indication) 2 -- SNR (Signal to Noise Ratio) 3 -- NF (Noise Floor) where value of n is: 1 -- Beacon last 2 -- Beacon average 3 -- Data last 4 -- Data average Examples: iwpriv mlan0 getsignal 1 : Get the RSSI info (beacon last, beacon average, data last and data average) iwpriv mlan0 getsignal 3 4 : Get the NF of data average iwpriv mlan0 getsignal 2 1 : Get the SNR of beacon last iwpriv mlan0 getsignal : Get all of the signal info mlan0 getsignal:-32 -33 -35 -36 67 59 63 56 -99 -92 -98 -92 RSSI info: beacon last -32, beacon average -33, data last -35, data average -36 SNR info: beacon last 67, beacon average 59, data last 63, data average 56 NF info: beacon last -99, beacon average -92, data last -98, data average -92 antcfg This command is used to set/get the mode of Tx/Rx path. where value of m is: Bit 0 -- Tx Path A Bit 1 -- Tx Path B Bit 0-1 -- Tx Path A+B where value of n is: Bit 0 -- Rx Path A Bit 1 -- Rx Path B Bit 0-1 -- Rx Path A+B The Tx path setting (m) is used if Rx path (n) is not provided. Examples: iwpriv mlan0 antcfg : Get Tx and Rx path iwpriv mlan0 antcfg 3 : Set Tx and Rx path to A+B iwpriv mlan0 antcfg 1 3 : Set Tx path to A and Rx path to A+B regioncode This command is used to set/get the region code in the station. Note: This command should be issued at beginning before band/channel selection and association. where value is 'region code' for various regions like USA FCC, Canada IC, Europe ETSI, Japan ... The special code (0xff) is used for Japan to support channel 1-14 in B/G/N mode. Examples: iwpriv mlan0 regioncode : Get region code iwpriv mlan0 regioncode 0x10 : Set region code to USA (0x10) Note : in some case regioncode will be 0 after updated countycode or 80211d i.e. mlanutl mlanX countrycode (CA, JP, CN, DE, ES AT, BR, RU) or uaputl.exe sys_cfg_80211d state 1 country (CA, JP, CN, DE, ES AT, BR, RU) Please use cfp instead of it. cfpcode This command is used to set/get the Channel-Frequency-Power table codes. The region table can be selected through region code. The current configuration is returned if no parameter provided. where the parameters are, [m]: code of the CFP table for 2.4GHz (0: unchanged) [n]: code of the CFP table for 5GHz (0 or not provided: unchanged) Examples: iwpriv mlan0 cfpcode : Get current configuration iwpriv mlan0 cfpcode 0x30 : Set 2.4GHz CFP table code 0x30 (EU), keep 5GHz table unchanged iwpriv mlan0 cfpcode 0x10 5 : Set 2.4GHz CFP table code 0x10 (USA) and 5GHz table code 5 wwscfg This command is used to set/get the WWS (World Wide Safe) mode. where value of m is: 0 -- Disable WWS mode (default) 1 -- Enable WWS mode Examples: iwpriv mlan0 wwscfg : Get WWS mode iwpriv mlan0 wwscfg 1 : Enable WWS mode iwpriv mlan0 wwscfg 0 : Disable WWS mode esuppmode This command is used to get the current RSN mode and active pairwise/group cipher for WPA/WPA2 mode. Note: This command is available only when STA is connected. These are bits settings used to indicate each RSN mode. Bit 0 : No RSN Bit 1-2 : RFU Bit 3 : WPA Bit 4 : WPA-NONE Bit 5 : WPA2 Bit 6 : AES Bit 7-15 : RFU These are bits settings used to indicate each pairwise and group cipher. Bit 0 : RFU Bit 1 : RFU Bit 2 : TKIP Bit 3 : AES Bit 2-7 : RFU Example: iwpriv mlan0 esuppmode : Get RSN mode and pairwise/group cipher 8 4 4 (The current RSN mode is WPA, active pairwise cipher is TKIP and active group cipher is TKIP.) passphrase This command is used to set/get passphrase for WPA-PSK/WPA2-PSK mode. Where ASCII string for ssid/passphrase/psk. 1) "0;" - This will get the passphrase, AKMP for specified ssid, if none specified then it will get all. Example: iwpriv mlan0 passphrase "0;ssid=marvell" 2) "1;; " - Passphrase and psk cannot be provided for the same SSID. This command takes only one SSID at a time, If ssid= is present it should contain a passphrase or psk. If no arguments are provided then AKMP=802.1x, and passphrase should be provided after association. End of each parameter should be followed by a ';'(except for the last parameter) as the delimiter. If ';' or '/' has to be used in an SSID then a '/' should be preceded to ';' or '/' as a escape. Examples: iwpriv mlan0 passphrase "1;ssid=mrvlAP;passphrase=abcdefgd" iwpriv mlan0 passphrase "1;ssid=mrvl AP;psk=<64 bytes hexpsk>" If user wants to input the ssid as "mrvl; AP" then command has to be iwpriv mlan0 passphrase "1;ssid=mrvl/; AP;passphrase=abcdefgh" If user wants to input the ssid as "//;" then command has to be iwpriv mlan0 passphrase "1;ssid=/////;;passphrase=abcdefgh" 3) "2;" - This will clear the passphrase for specified ssid, if none specified then it will clear all. Examples: iwpriv mlan0 passphrase "2;ssid=marvell" iwpriv mlan0 passphrase "2" : Clear all profiles and disable embedded supplicant httxcfg This command is used to configure various 11n specific configuration for transmit (such as Short GI, Channel BW and Green field support) where is This is a bitmap and should be used as following Bit 15-8: Reserved set to 0 Bit 7: STBC enable/disable Bit 6: Short GI in 40 Mhz enable/disable Bit 5: Short GI in 20 Mhz enable/disable Bit 4: Green field enable/disable Bit 3-2: Reserved set to 1 Bit 1: 20/40 Mhz enable disable. Bit 0: LDPC enable/disable When Bit 1 is set then firmware could transmit in 20Mhz or 40Mhz based on rate adaptation. When this bit is reset then firmware will only transmit in 20Mhz. where is - This is the band info for settings. 0: Settings for both 2.4G and 5G bands 1: Settings for 2.4G band 2: Settings for 5G band Examples: iwpriv mlanX httxcfg This will display HT Tx configuration. If the configurations for 2.4G and 5G are different, the first value is for 2.4G and the second value is for 5G. Otherwise, it will display a single value for both bands. iwpriv mlanX httxcfg 0x62 This will enable 20/40 and Short GI but will disable Green field for 2.4G and 5G band. iwpriv mlanX httxcfg 0x30 1 This will enable Short GI 20 Mhz and Green field for 2.4G band. The default value is 0x20 for 2.4G and 0x62 for 5G. Note:- If 20/40 MHz support is disabled in htcapinfo, device will not transmit in 40 MHz even 20/40 MHz is enabled in httxcfg. htcapinfo This command is used to configure some of parameters in HTCapInfo IE (such as Short GI, Channel BW, and Green field support) where is - This is a bitmap and should be used as following Bit 29: Green field enable/disable Bit 26: Rx STBC Support enable/disable. (As we support single spatial stream only 1 bit is used for Rx STBC) Bit 24: Short GI in 40 Mhz enable/disable Bit 23: Short GI in 20 Mhz enable/disable Bit 17: 20/40 Mhz enable disable. Bit 8: Enable/disable 40Mhz Intolarent bit in ht capinfo. 0 will reset this bit and 1 will set this bit in htcapinfo attached in assoc request. All others are reserved and should be set to 0. Setting of any other bits will return error. where is - This is the band info for settings. 0: Settings for both 2.4G and 5G bands 1: Settings for 2.4G band 2: Settings for 5G band Examples: iwpriv mlanX htcapinfo This will display HT capabilties information. If the information for 2.4G and 5G is different, the first value is for 2.4G and the second value is for 5G. Otherwise, it will display a single value for both bands. iwpriv mlanX htcapinfo 0x1820000 This will enable Short GI, Channel BW to 20/40 and disable Green field support for 2.4G and 5G band. iwpriv mlanX htcapinfo 0x800000 2 This will enable Short GI, Channel BW to 20 only, No Rx STBC support and disable Green field support for 5G band. The default value is 0x4800000 for 2.4G and 0x5820000 for 5G. Note:- This command can be issued any time but it will only come to effect from next association. (as HTCapInfo is sent only during Association). addbapara This command can be used to update the default ADDBA parameters. where is - This is the block ack timeout for ADDBA request. 0 : Disable (recommended for throughput test) 1 - 65535 : Block Ack Timeout in TU where is - Window size for ADDBA request. (16 is recommended and default value) where is - Window size for ADDBA response. (48 is recommended and 32 is default value) (16 is recommended for IWNCOMM AP in WAPI throughput test) Current window size limit for Tx as well as Rx is 1023. where

is - amsdu support for ADDBA request. (1 is default value) 0: disable amsdu in ADDBA request 1: enable amsdu in ADDBA request where is - amsdu support for ADDBA response. (1 is default value) 0: disable amsdu in ADDBA response 1: enable amsdu in ADDBA response eg: iwpriv mlanX addbapara - This command will get the current addba params iwpriv mlanX addbapara 1000 64 8 0 0 - This will change the ADDBA timeout to (1000 * 1024) us, txwinsize to 64 and rxwinsize to 8 and disable amdsu in ADDBA request/response. The default setting is 65535 16 32 1 1. In case the ADDBA timeout value is updated then a ADDBA is sent for all streams to update the timeout value. In case txwinsize and/or rxwinsize is updated, the effect could only be seen on next ADDBA request/response. The current streams will not be affected with this change. In case of txamsdu/rxamsdu is updated, the effect could only be seen on next ADDBA request/response. The current streams will not be affected with this change. AMSDU in AMPDU stream will be enabled when AP support this feature and AMSDU is enabled in aggrpriotbl. aggrpriotbl This command is used set/get the priority table for AMPDU/AMSDU traffic per tid. This command can also be used to disable AMPDU/AMSDU for a given tid. In case of AMPDU this priority table will be used to setup block ack (to make sure the highest priority tid always uses AMPDU as we have limited AMPDU streams) where ... - This is priority for Tid0 for AMPDU packet. A priority could be any values between 0 - 7, 0xff to disable aggregation. - This is priority for Tid0 for AMSDU packet. A priority could be any values between 0 - 7, 0xff to disable aggregation. eg: iwpriv mlanX aggrpriotbl - This command will get the current Priority table for AMPDU and AMSDU. <2 2 0 0 1 1 3 3 4 4 5 5 255 255 255 255>. This is read as <"Prio for AMPDU for Tid0" "Prio for AMSDU for Tid0" "Prio for AMPDU for Tid1" "Prio for AMSDU for Tid1" and so on iwpriv mlanX aggrpriotbl 2 2 0 0 1 1 3 3 4 4 5 5 255 255 255 255 - This will set the priority table for AMPDU and AMSDU Priority for Tid0/AMPDU = 2, Tid0/AMSDU = 2, Tid1/AMPDU = 0, Tid1/AMSDU = 0 and so on. Aggregation for Tid6 and Tid7 are disabled. Here higher the priority number, higher the priority (i.e. 7 has higher priority than 6). Similarly for AMSDU. iwpriv mlanX aggrpriotbl 0xff 2 0xff 0 0xff 1 0xff 3 0xff 4 0xff 5 0xff 0xff 0xff 0xff - This will disable AMPDU for all the TIDs but will still keep AMSDU enabled to Tid0 to Tid5 The default setting is 2 255 0 255 1 255 3 255 4 255 5 255 255 255 255 255. A delBA should be seen in case a disable happens on a TID for which AMPDU stream is currently setup. Note:- This command should only be issue in disconnected state. addbareject This command is used set/get the addbareject table for all the TIDs. This command can also be used to enable rejection of ADDBA requests for a given tid. where ... - This can be 0/1 for TidX. 1 enables rejection of ADDBA request for TidX and 0 would accept any ADDBAs for TidX. eg: iwpriv mlanX addbareject - This command will get the current table. [0 0 0 0 0 0 0 0]. ADDBA would be accepted for all TIDs. This is the default state. iwpriv mlanX addbareject 0 0 1 1 0 0 0 0 - This command will accept ADDBA requests for Tid [0,1,4,5,6,7] and reject ADDBA requests for Tid [2,3] iwpriv mlanX addbareject 1 1 1 1 1 1 1 1 - This will enable rejection of ADDBA requests for all Tids. Note:- This command should only be issue in disconnected state. txbufcfg This command can be used to get current buffer size. eg: iwpriv mlanX txbufcfg - This will display the current buffer size. Note:- The actual tx buf size will depends on AP's capability and max transmit buffer size. amsduaggrctrl This command could be used to enable/disable a feature where firmware gives feedback to driver regarding the optimal AMSDU buffer size to use with the current rate. Firmware will use the current rate to decide the buffer size we could transmit. The max buffer size will still be limited by buffer size provided in txbufcfg. (i.e. if the txbufcfg is 4K, then we could only transmit 4K/2K AMSDU packets, if the txbufcfg is 8K then we could transmit 8k/4k/2k based on current rate) If enabled AMSDU buffer size at various rates will be as follows 1. Legacy B/G rate. No AMSDU aggregation. 2. BW20 HT Rate: When TX rate goes down, MCS 7, 6, 5, 4: a 8K aggregation size (if TX buffer size is 8K) b 4K aggregation size (if TX buffer size is 4K) c 2K aggregation size (if TX buffer size is 2K) MCS 3, 2: a 4K aggregation size (if TX buffer size is 8K/4K) b 2K aggregation size (if TX buffer size is 2K) MCS 1, 0: a No aggregation When TX rate goes up, MCS 7, 6, 5: a 8K aggregation size (if TX buffer size is 8K) b 4K aggregation size (if TX buffer size is 4K) c 2K aggregation size (if TX buffer size is 2K) MCS 4, 3: a 4K aggregation size (if TX buffer size is 8K/4K) b 2K aggregation size (if TX buffer size is 2K) MCS 2, 1, 0: a No aggregation 3. BW40 HT Rate: When TX rate goes down, MCS 7, 6, 5, 4, 3, 2, 1: a 8K aggregation size (if TX buffer size is 8K) b 4K aggregation size (if TX buffer size is 4K) c 2K aggregation size (if TX buffer size is 2K) MCS 0: a No aggregation When TX rate goes up, MCS 7, 6, 5, 4, 3: a 8K aggregation size (if TX buffer size is 8K) b 4K aggregation size (if TX buffer size is 4K) c 2K aggregation size (if TX buffer size is 2K) MCS 2, 1, 0: a No aggregation where is 0/1 (for disable/enable) eg: iwpriv mlanx amsduaggrctrl 1 - Enable this feature iwpriv mlanx amsduaggrctrl 0 - Disable this feature iwpriv mlanx amsduaggrctrl - This will get the enable/disable flag and the current AMSDU buffer size). The AMSDU buffer size returned is only valid after association as before association there is no rate info. Note:- This command to enable/disable could be given anytime (before/after association). This feature is enabled by default by the driver during initialization. httxbfcap This command is used to set/get the TX beamforming capabilities. Usage: iwpriv mlanX httxbfcap [cap] where the parameters are, cap: TX beamforming capabilities Bit 0 : Implicit TX BF receiving capable Bit 1 : RX staggered sounding capable Bit 2 : TX staggered sounding capable Bit 3 : RX NDP capable Bit 4 : TX NDP capable Bit 5 : Implicit TX BF capable Bit 6-7 : Calibration 0: - not supported 1: - STA can respond to a calibration request using the CSI Report, but cannot initiate calibration 2: - reserved 3: - STA can both initiate and respond to a calibration request Bit 8 : Explicit CSI TX BF capable Bit 9 : Explicit non-compressed steering capable Bit 10 : Explicit compressed steering capable Bit 11-12: Explicit TX BF CSI feedback 0: - not supported 1: - delayed feedback 2: - immediate feedback 3: - delayed and immediate feedback Bit 13-14: Explicit non-compressed BF feedback capable 0: - not supported 1: - delayed feedback 2: - immediate feedback 3: - delayed and immediate feedback Bit 15-16: Explicit compressed BF feedback capable 0: - not supported 1: - delayed feedback 2: - immediate feedback 3: - delayed and immediate feedback Bit 17-18: Minimal grouping 0: - no grouping (STA supports groups of 1) 1: - groups of 1, 2 2: - groups of 1, 4 3: - groups of 1, 2, 4 Bit 19-20: CSI number of beamformer antennas supported 0: - single TX antenna sounding 1: - 2 TX antenna sounding 2: - 3 TX antenna sounding 3: - 4 TX antenna sounding Bit 21-22: Non-compressed steering number of beamformer antennas supported 0: - single TX antenna sounding 1: - 2 TX antenna sounding 2: - 3 TX antenna sounding 3: - 4 TX antenna sounding Bit 23-24: Compressed steering number of beamformer antennas supported 0: - single TX antenna sounding 1: - 2 TX antenna sounding 2: - 3 TX antenna sounding 3: - 4 TX antenna sounding Bit 25-26: CSI max number of rows beamformer supported 0: - single row of CSI 1: - 2 rows of CSI 2: - 3 rows of CSI 3: - 4 rows of CSI Bit 27-28: Channel estimation capability 0: - 1 space time stream 1: - 2 space time streams 2: - 3 space time streams 3: - 4 space time streams Bit 29-31: Reserved Examples: iwpriv mlan0 httxbfcap : Get the current TX BF capabilities iwpriv mlan0 httxbfcap 0x0000001F : Set the TX BF capabilities of the Implicit TX BF receiving capable, RX staggered sounding capable, TX staggered sounding capable, RX NDP capable and TX NDP capable httxbfcfg This command is used to configure the TX beamforming options. Note: Any new subcommand should be inserted in the second argument and each argument of the sub command should be separated by semicolon. For global configuration, the arguments should be separated by space. Usage: iwpriv mlanX httxbfcfg "[;GlobalData/tsData/interval/txPeerData/snrData]" where the parameters are, action: TX beamforming action 0: Control global parameters for beamforming 1: Performs NDP Sounding for PEER 2: TX BF interval in milliseconds 3: Enable/Disable beamforming/sounding for a particular peer 4: TX BF SNR Threshold for peer .. GlobalData: Global parameter arguments. It contains beamforming enable, sounding enable, FB type, snr_threshold sounding interval, Beamformig mode values seperated by space. Syntax: iwpriv mlanX httxbfcfg ; tsData: Trigger sounding for PEER specific arguments, it contains PEER MAC and status interval: TX BF interval in milliseconds txPeerData: Enable/Disable beamforming/sounding for the indicated peer, it contains PEER MAC, sounding, beamfoming options and FB type; snrData: TX BF SNR Threshold for peer, it contains PEER MAC and SNR Examples: iwpriv mlan0 httxbfcfg "0" : Get current global configuration parameter iwpriv mlan0 httxbfcfg "2;00:50:43:20:BF:64" : Get the TX BF periodicity for a given peer iwpriv mlan0 httxbfcfg "3" : Get the list of MAC addresses that have beamforming and/or sounding enabled iwpriv mlan0 httxbfcfg "4" : Get the list of PEER MAC, SNR tuples programmed into the firmware. iwpriv mlan0 httxbfcfg "0;0 0 3 10 500 5" : Disable beamforming, sounding, set FB type to 3, snr threshold to 10, sounding interval to 500 ms and beamforming mode to 5 iwpriv mlan0 httxbfcfg "1;00:50:43:20:BF:64" : Perform NDP Trigger sounding to peer 00:50:43:20:BF:64 iwpriv mlan0 httxbfcfg "2;00:50:43:20:BF:64;500" : Set TX BF periodicity for peer 00:50:43:20:BF:64 to 500 milliseconds iwpriv mlan0 httxbfcfg "3;00:50:43:20:BF:43;1;0;3" : Enable beamforming, disable sounding and set FB type to 3 for peer 00:50:43:20:BF:43 iwpriv mlan0 httxbfcfg "4;00:50:43:20:BF:24;43" : Set TX BF SNR threshold to peer 00:50:43:20:BF:24 with SNR 43 mgmtframectrl This command is used to get/set mask for the management frames which needs to be forwarded to application layer. Usage: iwpriv mlanX mgmtframectrl [m] where the parameter [m] is the bit mask of management frame reception. Following are the bit definitions. Bit 0 : Association Request Bit 1 : Association Response Bit 2 : Re-Association Request Bit 3 : Re-Association Response Bit 4 : Probe Request Bit 5 : Probe Response Bit 8 : Beacon Frames Examples: iwpriv mlan0 mgmtframectrl : Get the current Mgmt Frame forwarding mask iwpriv mlan0 mgmtframectrl 0x0020 : Bit 5 is set, Forward probe response frames to application layer deepsleep This command is used to set/get auto deep sleep mode. Usage: iwpriv mlanX deepsleep [n] [m] where the parameters are: [n]: Enable/disable auto deep sleep mode (1/0) [m]: Idle time in milliseconds after which firmware will put the device in deep sleep mode. Default value is 100 ms. Examples: iwpriv mlan0 deepsleep : Display auto deep sleep mode iwpriv mlan0 deepsleep 1 : Enable auto deep sleep mode, idle time unchanged iwpriv mlan0 deepsleep 0 : Disable auto deep sleep mode iwpriv mlan0 deepsleep 1 500 : Enable auto deep sleep mode with idle time 500 ms Note: Deepsleep must be disabled before changing idle time. hscfg This command is used to configure the host sleep parameters. Usage: iwpriv mlanX hscfg [condition [[GPIO# [gap]]]] This command takes one (condition), two (condition and GPIO#) or three (condition, GPIO# and gap) parameters for set. If no parameter provided, get is performed. where Condition is: bit 0 = 1 -- broadcast data bit 1 = 1 -- unicast data bit 2 = 1 -- mac event bit 3 = 1 -- multicast data bit 6 = 1 -- Wakeup when mgmt frame received. bit 7 = 1 -- Reserved bit 8 = 1 -- Disable non maskable data wakeup. The host sleep mode will be canceled if condition is set to -1. The default is 0x7. where GPIO is the pin number of GPIO used to wakeup the host. It could be any valid GPIO pin# (e.g. 0-7) or 0xff (interface, e.g. SDIO will be used instead). The default is 0xff. where Gap is the gap in milliseconds between wakeup signal and wakeup event or 0xff for special setting (host acknowledge required) when GPIO is used to wakeup host. The default is 200. The host sleep set except for cancellation will be blocked if host sleep is already activated. Examples: iwpriv mlan0 hscfg : Get current host sleep mode iwpriv mlan0 hscfg -1 : Cancel host sleep mode iwpriv mlan0 hscfg 3 : Broadcast and unicast data Use GPIO and gap set previously iwpriv mlan0 hscfg 2 3 : Unicast data Use GPIO 3 and gap set previously iwpriv mlan0 hscfg 2 1 0xa0 : Unicast data Use GPIO 1 and gap 160 ms iwpriv mlan0 hscfg 2 0xff : Unicast data Use interface (e.g. SDIO) Use gap set previously iwpriv mlan0 hscfg 4 3 0xff : MAC event Use GPIO 3 Special host sleep mode iwpriv mlan0 hscfg 1 0xff 0xff : Broadcast data Use interface (e.g. SDIO) Use gap 255ms hssetpara This command is used to set host sleep parameters. Usage: iwpriv mlanX hssetpara Condition [GPIO# [gap]] Note: 1) The usages of parameters are the same as "hscfg" command. 2) The parameters will be saved in the driver and be used when host suspends. deauth This command is used to send a de-authentication to an arbitrary AP. If [n] is omitted, the driver will deauth the associated AP. If in ad-hoc mode this command is used to stop beacon transmission from the station and go into idle state. When is supplied as a MAC address, the driver will deauth the specified AP. If the AP address matches the driver's associated AP, the driver will disconnect. Otherwise, the driver remains connected. radioctrl This command is used to turn on/off the radio. Note: The radio can be disabled only in disconnected state. where value of n is: 0 -- Disable 1 -- Enable Examples: iwpriv mlan0 radioctrl 1 : Turn the radio on iwpriv mlan0 radioctrl : Get radio status reassoctrl This command is used to turn on/off re-association in driver. Usage: iwpriv mlanX reassoctrl [n] Where value of n is: 0 -- Disable 1 -- Enable Examples: iwpriv mlan0 reassoctrl : Get re-association status iwpriv mlan0 reassoctrl 1 : Turn re-association on bandcfg This command is used to set/get infra/ad-hoc band. Note: This command is only available in disconnected state. Usage: iwpriv mlanX bandcfg [l] [m] [n] where the parameters: [l]: Infrastructure band bit 0: B bit 1: G bit 2: A bit 3: GN bit 4: AN bit 5: AC 2.4G bit 6: AC 5G [m]: Ad-hoc start band bit 0: B bit 1: G bit 2: A [n]: Ad-hoc start channel Examples: iwpriv mlan0 bandcfg : Get infra/ad-hoc band and ad-hoc start channel configurations iwpriv mlan0 bandcfg 1 : Set infra band to B only iwpriv mlan0 bandcfg 3 2 6 : Set infra band to B/G, ad-hoc start band to G and ad-hoc start channel to 6 getlog This command is used to get the statistics available in the station. 11dcfg This command is used to control 11D. No argument is used to get. where value of n is: 0 -- Disable 1 -- Enable Examples: iwpriv mlan0 11dcfg 1 : Enable 11D iwpriv mlan0 11dcfg : Get 11D status 11dclrtbl This command is used to clear the 11D channel table. Usage: iwpriv mlanX 11dclrtbl wmmcfg This command is used to control WMM. No argument is used to get. where value of n is: 0 -- Disable 1 -- Enable Examples: iwpriv mlan0 wmmcfg 1 : Enable WMM iwpriv mlan0 wmmcfg : Get WMM status txpowercfg This command is used to get/set the Tx power configuration. Where - Data rate index 0 1 Mbps 1 2 Mbps 2 5.5 Mbps 3 11 Mbps 4 6 Mbps 5 9 Mbps 6 12 Mbps 7 18 Mbps 8 24 Mbps 9 36 Mbps 10 48 Mbps 11 54 Mbps 12 MCS0 (BW20) 13 MCS1 (BW20) 14 MCS2 (BW20) 15 MCS3 (BW20) 16 MCS4 (BW20) 17 MCS5 (BW20) 18 MCS6 (BW20) 19 MCS7 (BW20) 20 MCS8 (BW20) 21 MCS9 (BW20) 22 MCS10 (BW20) 23 MCS11 (BW20) 24 MCS12 (BW20) 25 MCS13 (BW20) 26 MCS14 (BW20) 27 MCS15 (BW20) 140 MCS0 (BW40) 141 MCS1 (BW40) 142 MCS2 (BW40) 143 MCS3 (BW40) 144 MCS4 (BW40) 145 MCS5 (BW40) 146 MCS6 (BW40) 147 MCS7 (BW40) 148 MCS0 (BW40) 149 MCS1 (BW40) 150 MCS2 (BW40) 151 MCS3 (BW40) 152 MCS4 (BW40) 153 MCS5 (BW40) 154 MCS6 (BW40) 155 MCS7 (BW40) 0xff Default - Minimum power level in dBm - Maximum power level in dBm - Power step Note: Firmware may adjust the setting if over limit, final value can be verified using get command. Examples: iwpriv mlan0 txpowercfg 0xff : Default power configuration iwpriv mlan0 txpowercfg 11 12 : Set power level 12 dBm to data rate 54 Mbps iwpriv mlan0 txpowercfg 7 11 16 1 : Set power level 11 dBm to 16 dBm with step 1 to data rate 18 Mbps iwpriv mlan0 txpowercfg : Get current configuration mlan0 txpowercfg:2 3 13 18 2 1 1 13 18 2 0 0 13 18 2 10 11 13 15 2 8 9 13 16 2 6 7 13 17 2 4 5 13 17 2 17 19 13 15 2 15 16 13 16 2 13 14 13 17 2 12 12 13 17 2 145 147 13 14 1 143 144 13 14 1 141 142 13 14 1 140 140 13 14 1 2 -> First rate index is 5.5 Mbps. 3 -> Last rate index is 11 Mbps. 13 -> Min Tx power value is 13 dBm. 18 -> Max Tx power value is 18 dBm. 2 -> Power adjustment step value is 2. Similarly 17 -> First rate index is MCS5 (BW20). 19 -> Last rate index is MCS7 (BW20). 13 -> Min Tx power value is 13 dBm. 15 -> Max Tx power value is 15 dBm. 2 -> Power adjustment step value is 2. so on... qoscfg This command sets WMM IE QOS info when an argument is given, and gets current WMM IE QOS info when no argument is given. Examples: iwpriv mlan0 qoscfg 0x0f : Set WMM IE QOS info to 0x0f iwpriv mlan0 qoscfg : Get WMM IE QOS info getdatarate This command is used to get the data rate (index) being used in last Tx packet and last Rx packet. bcninterval This command is used to set/get the beacon interval in ad-hoc mode. The valid beacon interval is between 20 - 1000, default beacon interval is 100. Where Beacon interval in TU (Time Unit: 1024 us). Examples: iwpriv mlan0 bcninterval 200 : Set ad-hoc beacon interval to 200 iwpriv mlan0 bcninterval : Get ad-hoc beacon interval sysclock This command is used to set/get system clocks in MHz. The current system clock, configurable system clocks and all of the supported system clocks will be returned if no parameter provided. Examples: iwpriv mlan0 sysclock : Get system clocks 80 80 128 128 128 5 11 16 20 22 32 40 44 64 80 106 128 160 ... (The current system clock is 80 MHz. The configurable system clocks of non-security, security, non-security A-MPDU and security A-MPDU are 80 MHz, 128 MHz, 128 MHz and 128 MHz. The supported system clocks are 5 MHz, 11 MHz, ..., 160 MHz, 182 MHz, 213 MHz, 256 MHz, 320 Mhz, 366 MHz , ... . the Max system clocks is different for different chips, you could use this command to get the supported system clock) iwpriv mlanX sysclock 80 : Set system clock in non-security mode to 80 MHz, no change for others iwpriv mlanX sysclock 0 0 128 : Set system clock in non-security A-MPDU mode to 128 MHz, no changes for others drvdbg This command is used to set/get the bit masks of driver debug message control. Usage: iwpriv mlanX drvdbg [n] Where the parameter is the generic debug message control bit mask. The following types of driver debug messages can be dynamically enabled or disabled by setting or clearing the corresponding bits, bit 0: MMSG PRINTM(MMSG,...) bit 1: MFATAL PRINTM(MFATAL,...) bit 2: MERROR PRINTM(MERROR,...) bit 3: MDATA PRINTM(MDATA,...) bit 4: MCMND PRINTM(MCMND,...) bit 5: MEVENT PRINTM(MEVENT,...) bit 6: MINTR PRINTM(MINTR,...) bit 7: MIOCTL PRINTM(MIOCTL,...) ... bit 16: MDAT_D PRINTM(MDAT_D,...), DBG_HEXDUMP(MDAT_D,...) bit 17: MCMD_D PRINTM(MCMD_D,...), DBG_HEXDUMP(MCMD_D,...) bit 18: MEVT_D PRINTM(MEVT_D,...), DBG_HEXDUMP(MEVT_D,...) bit 19: MFW_D PRINTM(MFW_D,...), DBG_HEXDUMP(MFW_D,...) bit 20: MIF_D PRINTM(MIF_D,...), DBG_HEXDUMP(MIF_D,...) ... bit 28: MENTRY PRINTM(MENTRY,...), ENTER(), LEAVE() bit 29: MWARN PRINTM(MWARN,...) bit 30: MINFO PRINTM(MINFO,...) If CONFIG_DEBUG=2, all kinds of debug messages can be configured. If CONFIG_DEBUG=1, all kinds of debug messages can be configured except for MENTRY, MWARN and MINFO. By default MMSG, MFATAL and MERROR are enabled. Some special debug messages, '*' // MLAN driver ISR is called (bit 6 MINTR enabled) '|' // PS awake event is received (bit 5 MEVENT enabled) '_' // PS sleep event is received (bit 5 MEVENT enabled) '+' // PS sleep confirm is sent (bit 5 MEVENT enabled) Examples: iwpriv mlan0 drvdbg : Get the current driver debug masks iwpriv mlan0 drvdbg 0 : Disable all the debug messages iwpriv mlan0 drvdbg 7 : Enable MMSG, MFATAL and MERROR messages iwpriv mlan0 drvdbg 0x20037 : Enable MMSG, MFATAL, MEEROR, MCMND, MEVENT and MCMD_D messages iwpriv mlan0 drvdbg -1 : Enable all the debug messages warmreset This command is used for warm reset of the interface. Usage: iwpriv mlanX warmreset regrdwr This command is used to read/write the adapter register. Usage: iwpriv mlanX regrdwr [value] where the parameters are, : 1:MAC/SOC, 2:BBP, 3:RF, 5:CAU : offset of register [value]: value to be written Note: If highest bit of a 32-bit value needs to be set, use negative input. The calculation is -(0xffffffff - value + 1). Range from -0x80000000 to -1. Examples: iwpriv mlan0 regrdwr 1 0xa060 : Read the MAC register iwpriv mlan0 regrdwr 1 0xa060 0x12 : Write the MAC register iwpriv mlan0 regrdwr 1 0xa794 -0x80000000 : Write 0x80000000 to MAC register iwpriv mlan0 regrdwr 1 0xa794 -0x00000001 : Write 0xffffffff to MAC register rdeeprom This command is used to read the EEPROM contents of the card. Usage: iwpriv mlanX rdeeprom where the parameters are, : multiples of 4 : 4-20, multiples of 4 Example: iwpriv mlan0 rdeeprom 0 20 : Read 20 bytes of EEPROM data from offset 0 memrdwr This command is used to read/write the adapter memory. Usage: iwpriv mlanX memrdwr

[value] where the parameters are,
: memory address [value]: value to be written Note: If highest bit of a 32-bit address/value needs to be set, use negitive input. The calculation is -(0xffffffff - address/value + 1). Range from -0x80000000 to -1. Examples: iwpriv mlan0 memrdwr 0x4cf70 : Read memory address 0x4cf70 iwpriv mlan0 memrdwr -0x80000000 : Read memory address 0x80000000 iwpriv mlan0 memrdwr -0x7fff6000 -0x40000000 : Write 0xc0000000 to memory address 0x8000a000 inactivityto This command is used to set/get the inactivity timeout value, which specifies when WLAN device is put to sleep. Usage: iwpriv mlanX inactivityto [k] where the parameter are: : timeout unit in microseconds. : Inactivity timeout for unicast data. : Inactivity timeout for multicast data. [k]: Inactivity timeout for new Rx traffic after PS notification to AP. Examples: iwpriv mlan0 inactivityto : Get the timeout value iwpriv mlan0 inactivityto 1000 2 3 : Set timeout unit to 1000 us (1 ms), inactivity timeout for unicast data is 2 ms, inactivity timeout for multicast data is 3 ms scancfg This command is used to set/get scan configuration parameters. Usage: iwpriv mlanX scancfg [t] [m] [p] [s] [a] [b] [ext] where the parameters: [t]: Scan Type (0: Unchanged, 1: Active, 2: Passive, default Active) [m]: Scan Mode (0: Unchanged, 1: BSS, 2: IBSS, 3: Any, default Any) [p]: Scan Probes (0: Unchanged, 1-4: Number of probes per channel, default 4) [s]: Specific Scan Time (0: Unchanged, n: Value in ms, default 110 ms, max 500 ms) [a]: Active Scan Time (0: Unchanged, n: Value in ms, default 200 ms, max 500 ms) [b]: Passive Scan Time (0: Unchanged, n: Value in ms, default 200 ms, max 2000 ms) [ext]: Extended scan (0: Legacy scan, 1: Extended scan) No change if the parameter is 0 or the parameter is not provided. Examples: iwpriv mlan0 scancfg : Get all the current scan configuration settings iwpriv mlan0 scancfg 1 3 : Set scan type to active and scan mode to any, all the other scan configurations are unchanged iwpriv mlan0 scancfg 0 1 2 200 : Set scan mode to BSS, number of probes to 2 and specific scan time to 200 ms, all the other scan configurations are unchanged sleeppd This command is used to configure the sleep period of the WLAN device. Usage: iwpriv mlanX sleeppd [] Where the parameter is: period: sleep period in milliseconds. Range 10~60. 0 for disable. Examples: iwpriv mlan0 sleeppd : Get sleep period configuration iwpriv mlan0 sleeppd 10 : Set sleep period to 10 ms pscfg This command is used to set/get PS configuration parameters. Usage: iwpriv mlanX pscfg [k] [d] [l] ... Where the parameters: [k]: Keep alive null packet interval (0: Unchanged, -1: Disable, n: Interval in seconds) [d]: DTIM interval ( 0: Unchanged, 1-5: Value, 65534: DTIM will be ignored, listen interval will be used, 65533: Closest DTIM to the listen interval period will be used ) [l]: Local listen interval ( 0: Unchanged, -1: Disable, 1-49: Value in beacon intervals, >= 50: Value in TUs ) [b]: Beacon miss timeout (0: Unchanged, 1-50: Value in milliseconds, 65535: Disable) [p]: Delay to PS (0-65535: Value in milliseconds, default 1000ms) [m]: PS mode (0: Unchanged, 1: Auto mode, 2: PS-Poll mode, 3: PS Null mode) No change if parameters are not provided. Examples: iwpriv mlan0 pscfg : Get all the current PS configuration settings iwpriv mlan0 pscfg 3 4 : Set PS keep alive null packet interval to 3 seconds and DTIM interval to 4, all the other configurations are unchanged iwpriv mlan0 pscfg 0 0 0 0 50 2 : Set delay to PS to 50 ms and PS mode to PS-Poll mode, keep the others unchanged fwwakeupmethod This command is used to set/get the firmware wakeup method. where value is: [n]: 1 -- Firmware wakeup through the interface command interrupt -- (default setting for SDIO/PCIe/USB) 2 -- Firmware wakeup through the GPIO pin [g]:If firware wakeup throug GPIO pin, [g] is GPIO pin number Examples: iwpriv mlan0 fwwakeupmethod : Get current firmware wakeup method iwpriv mlan0 fwwakeupmethod 1 : Set firmware wakeup method to Interface mode iwpriv mlan0 fwwakeupmethod 2 5 : Set firmware wakeup method to GPIO mode, GPIO_pin=5 getkey This command is used to get PTK/GTK iwpriv mlanX getkey associate Request an association to a given SSID/BSSID pair. This the only accurate way to pick a specific AP and ESS for an association. The entry must already exist in the scan table for the association to be attempted. iwpriv mlanX associate "xx:xx:xx:xx:xx:xx SSID" sleepparams This command is used to set the sleepclock configurations Usage: iwpriv mlanX sleepparams [ ] where: p1 is Sleep clock error in ppm (0-65535) p2 is Wakeup offset in usec (0-65535) p3 is Clock stabilization time in usec (0-65535) p4 is Control periodic calibration (0-2) p5 is Control the use of external sleep clock (0-2) p6 is reserved for debug (0-65535) Examples: iwpriv mlan0 sleepparams : Get current sleepclock configuration iwpriv mlan0 sleepparams 10 1000 2000 1 0 128 : Set sleepclock configuration netmon This command is used to set/get sniffer mode configuration. Note: The channel and band config is optional. If not specified, or if any STA/uAP/STA+uAP connection is active, sniffer activity will be started on the current config set in the FW. 'rtap' monitor interface will be created on enabling sniffer activity and should be made 'up' for capturing in a sniffer app. Usage: iwpriv netmon [ []] iwpriv netmon [ [] [ [offset]]] Where the parameters are: : mlanX, uapX : (1/0) enable/disable sniffer activity : network monitor filer flag bit 0: (1/0) enable/disable management frame bit 1: (1/0) enable/disable control frame bit 2: (1/0) enable/disable data frame bit 3: (1/0) enable/disable frames destined to active connection only bit 4: (1/0) enable/disable decrypted unicast data/mgmt frames : 802.11 band bit 0: B bit 1: G bit 2: A bit 3: GN bit 4: AN bit 5: AC 2.4G bit 6: AC 5G : channel to monitor [offset] : secondary channel bandwidth 0 - Bandwidth 20Mhz 1 - HT Bandwidth 40Mhz sec channel above 3 - HT Bandwidth 40Mhz sec channel below 4 - VHT Bandwidth 80Mhz Examples: iwpriv mlan0 netmon : Get the current sniffer mode configuration iwpriv mlan0 netmon 0 : Disable network monitor activity iwpriv uap0 netmon 1 7 : Enable sniffer activity on current channel set in FW, set filter data, control, management frame. iwpriv mlan0 netmon 1 4 11 6 : Enable sniffer activity in absence of active connection, set filter data frame, band B/G/GN and channel 6 iwpriv mlan0 netmon 1 7 20 64 1 : Enable sniffer activity in absence of active connection, set filter management, control and data frame, band A/AN, channel 64 and secondary channel above iwpriv uap0 netmon 1 0x0c : Enable sniffer activity, set filter data frames destined to the active uAP connection only iwpriv mlan0 netmon 1 0x1d : Enable sniffer activity, set filter decrypted data and management frames destined to the active STA connection only authtype This command is used to set/get authentication type. Usage: iwpriv mlanX authtype [n] where 0: 802.11 open system authentication 1: 802.11 shared key authentication 255: allow open system or shared key authentication (default) Examples: iwpriv mlan0 authtype 0 : use open system authentication iwpriv mlan0 authtype 1 : use shared key authentication iwpriv mlan0 authtype 255 : allow open system or shared key authentication iwpriv mlan0 authtype : get current setting powercons This command is used to set the local transmit power constraint. Value is in dbm unit. This command is only used for ad-hoc start. Usage: iwpriv mlanX powercons [n] Examples: iwpriv mlanX powercons : get the current setting iwpriv mlanX powercons 12 : set local power constraint to 12 dbm htstreamcfg This command is used to set/get HT stream configuration. The setting only takes effect in next association. Usage: iwpriv mlanX htstreamcfg [n] where 0x11: HT stream 1x1 mode 0x22: HT stream 2x2 mode Examples: iwpriv mlan0 htstreamcfg : Get current setting iwpriv mlan0 htstreamcfg 0x11 : Set HT stream 1x1 mode iwpriv mlan0 htstreamcfg 0x22 : Set HT stream 2x2 mode ipaddr This command is used to set/get IP address. Usage: iwpriv mlanX ipaddr [";"] where 0: Remove the IP address bit 0: Set IP address for broadcast ARP filter, which will be auto enabled in next host sleep configuration bit 1: Set IP address for auto broadcast ARP response Examples: iwpriv mlan0 ipaddr : Get current settings iwpriv mlan0 ipaddr "0" : Remove IP address iwpriv mlan0 ipaddr "1;192.168.0.5" : Set IP address for ARP filter iwpriv mlan0 ipaddr "3;192.168.0.6" : Set IP address for ARP filter : and auto ARP response macctrl This command is used to set/get MAC control. It's recommended to read the current setting first to avoid override issue. Usage: iwpriv mlanX macctrl [n] where bit 0: Rx enabled bit 1: Tx enabled bit 3: WEP enabled bit 4: EthernetII enabled bit 7: Promiscuous enabled bit 8: All multicast enabled bit 9: RTS/CTS enabled (0: CTS to self) bit 11: Force 11n protection disabled bit 12: Ad-hoc g protection disabled ... Examples: iwpriv mlan0 macctrl : Get current MAC control iwpriv mlan0 macctrl 0x13 : Set Tx/Rx on and EthernetII on iwpriv mlan0 macctrl 0x813 : Set Tx/Rx on and EthernetII on : Disable force 11n protection dfstesting This command is used to set/get settings for DFS testing. Usage: iwpriv mlanX dfstesting [ ] where is user-configured Channel Availability Check in msec 0 = disable, use default period (60000) 1-65535 = enable with that period where is user-configured Non-Occupancy Period in sec 0 = disable, use default period (1800) 1-65535 = enable with that period where is enable/disable no channel change on radar 0 = disable, 1 = enable (overrides below) where is user-configured channel to change to on radar 0 = disable, 1-255 = enable with that channel (channel validity for region, etc. is not checked) (only takes effect if no_chan_change = 0) Examples: iwpriv mlan0 dfstesting : Get current dfstesting settings iwpriv mlan0 dfstesting 2000 0 0 0 : user_cac=2sec, others disabled/default iwpriv mlan0 dfstesting 0 0 1 0 : only no_chan_change enabled iwpriv mlan0 dfstesting 0 120 0 64 : user_nop=2min, force chan 64 on radar indrstcfg This command is used to set/get settings for independent reset mode Usage: iwpriv mlanX indrstcfg [gpio_pin] where is independent reset mode 0 = disable independent reset 1 = enable out band and disable in band 2 = enable in band and disable out band where is user-configured gpio pin number to be used for oob mode 0xFF = use FW default gpio assignment 0-15 = gpio pin number Examples: iwpriv mlan0 indrstcfg : Get current settings iwpriv mlan0 indrstcfg 1 14 : Enable oob_mode with gpio pin 14 iwpriv mlan0 indrstcfg 1 0xff : Enable oob_mode with default gpio pin iwpriv mlan0 indrstcfg 0 : Disable ir_mode iwpriv mlan0 indrstcfg 2 : Enable in band reset mode =============================================================================== U S E R M A N U A L F O R M L A N C O N F I G NAME mlanconfig - configure the additional parameters available for the Marvell mdriver. SYNOPSIS mlanconfig -v mlanconfig [parameters] ... mlanconfig mlanX hostcmd bgscfg mlanconfig mlanX hostcmd requesttpc mlanconfig mlanX hostcmd crypto_test mlanconfig mlanX hostcmd subevent_get mlanconfig mlanX hostcmd subevent_set mlanconfig mlanX hostcmd auto_tx_get mlanconfig mlanX hostcmd nat_keep_alive mlanconfig mlanX hostcmd auto_tx_unreg mlanconfig mlanX hostcmd txrate_cfg_get mlanconfig mlanX hostcmd txrate_cfg_set_bg mlanconfig mlanX hostcmd txrate_cfg_set_bgn mlanconfig mlanX hostcmd txpwrlimit_cfg_get mlanconfig mlanX hostcmd txpwrlimit_2g_cfg_set mlanconfig mlanX hostcmd txpwrlimit_5g_cfg_set mlanconfig mlanX hostcmd pad_cfg_get mlanconfig mlanX hostcmd pad_cfg_set mlanconfig mlanX hostcmd <11n_2040coex.conf> 2040coex mlanconfig mlanX hostcmd mode_get mlanconfig mlanX hostcmd mode_timeshare mlanconfig mlanX hostcmd mode_spatial mlanconfig mlanX hostcmd generictime mlanconfig mlanX hostcmd a2dptime mlanconfig mlanX hostcmd inquirytim mlanconfig mlanX hostcmd ap_generictime mlanconfig mlanX hostcmd ap_a2dptime mlanconfig mlanX hostcmd ap_inquirytime mlanconfig mlanX arpfilter mlanconfig mlanX mefcfg mlanconfig mlanX cfgdata mlanconfig mlanX setuserscan [ARGS] mlanconfig mlanX getscantable [ARGS] mlanconfig mlanX addts mlanconfig mlanX delts mlanconfig mlanX qconfig set msdu [Queue Id: 0-3] mlanconfig mlanX qconfig get [Queue Id: 0-3] mlanconfig mlanX qconfig def [Queue Id: 0-3] mlanconfig mlanX qstats on [Queue Id: 0-3] mlanconfig mlanX qstats off [Queue Id: 0-3] mlanconfig mlanX qstats get [Queue Id: 0-3] mlanconfig mlanX qstatus mlanconfig mlanX ts_status mlanconfig mlanX regrdwr [value] mlanconfig mlanX memrdwr
[value] mlanconfig mlanX customie mlanconfig mlanX tdls_config <0/1> mlanconfig mlanX tdls_setinfo mlanconfig mlanX tdls_setup mlanconfig mlanX tdls_discovery mlanconfig mlanX tdls_teardown mlanconfig mlanX tdls_powermode mlanconfig mlanX tdls_channel_switch mlanconfig mlanX tdls_stop_channel_switch mlanconfig mlanX tdls_cs_params mlanconfig mlanX tdls_disable_cs <0/1> mlanconfig mlanX tdls_link_status mlanconfig mlanX tdls_debug "wrong_bss" <0/1> mlanconfig mlanX tdls_debug "setup_existing_link" <0/1> mlanconfig mlanX tdls_debug "fail_setup_confirm" <0/1> mlanconfig mlanX tdls_debug "setup_with_prohibited" <0/1> mlanconfig mlanX tdls_debug "higher_lower_mac" <0/1> mlanconfig mlanX tdls_debug "ignore_key_expiry" <0/1> mlanconfig mlanX tdls_debug "allow_weak_security" <0/1> mlanconfig mlanX tdls_debug "stop_rx" <0/1> mlanconfig mlanX tdls_debug "cs_im_return" <0/1> mlanconfig mlanX mgmtframetx DESCRIPTION Those commands are used in Marvell specific application called mlanconfig. =========== -v This command is used to display the version of mlanconfig utility. Usage: mlanconfig -v hostcmd bgscfg This command is used to configure the various parameters for PPS/UAPSD or normal background scan. Usage: mlanconfig mlanX hostcmd config/bg_scan.conf bgscfg hostcmd requesttpc This command is used to request 802.11H TPC info. Usage: mlanconfig mlanX hostcmd config/requesttpc.conf requesttpc hostcmd crypto_test This command is used to test the encryption/decryption API of the firmware. Usage: mlanconfig mlanX hostcmd config/crypto_test.conf crypto_test hostcmd subevent_get hostcmd subevent_set This command is used to get/set the configurations for event descriptor interface command. subsvent_get: get subscribed event parameters subsvent_set: set subscribed event parameters Usage: mlanconfig mlanX hostcmd config/subevent.conf subevent_get mlanconfig mlanX hostcmd config/subevent.conf subevent_set hostcmd auto_tx_get hostcmd nat_keep_alive hostcmd auto_tx_unreg This command is used to configures the Frame Auto Transmission parameters. auto_tx_get: get auto_tx parameters nat_keep_alive: register to firmware for sending NAT Keep Alive packet auto_tx_unreg: unregister to firmware auto_tx Usage: mlanconfig mlanX hostcmd config/auto_tx.conf auto_tx_get mlanconfig mlanX hostcmd config/auto_tx.conf nat_keep_alive mlanconfig mlanX hostcmd config/auto_tx.conf auto_tx_unreg hostcmd txrate_cfg_get hostcmd txrate_cfg_set_bg hostcmd txrate_cfg_set_bgn This command is used to set/get the transmit data rate. Usage: mlanconfig mlanX hostcmd config/txrate_cfg.conf txrate_cfg_get mlanconfig mlanX hostcmd config/txrate_cfg.conf txrate_cfg_set_bg mlanconfig mlanX hostcmd config/txrate_cfg.conf txrate_cfg_set_bgn hostcmd txpwrlimit_cfg_get hostcmd txpwrlimit_2g_cfg_set hostcmd txpwrlimit_5g_cfg_set This command is used to set/get the configuration data of Tx power limitation. Note: The configuration set should be issued when STA is disconnected. Usage: mlanconfig mlanX hostcmd config/txpwrlimit_cfg.conf txpwrlimit_cfg_get mlanconfig mlanX hostcmd config/txpwrlimit_cfg.conf txpwrlimit_2g_cfg_set mlanconfig mlanX hostcmd config/txpwrlimit_cfg.conf txpwrlimit_5g_cfg_set hostcmd pad_cfg_get hostcmd pad_cfg_set This command is used to set/get the configuration data for PAD OR. Usage: mlanconfig mlanX hostcmd config/pad_cfg.conf pad_cfg_get mlanconfig mlanX hostcmd config/pad_cfg.conf pad_cfg_set hostcmd 2040coex This command is used to send the 11n 20/40 Coex command to firmware. Firmware will send 11n 20/40 Coex management action frame to AP. Usage: mlanconfig mlanX hostcmd config/11n_2040coex.conf 2040coex hostcmd mode_get hostcmd mode_timeshare hostcmd mode_spatial This command is used to get/set Robust BT Coex. mode_get: get the current mode mode_timeshare: set Robust BT Coex to timeshare mode (default on 1x1 chips) mode_spatial: set Robust BT Coex to spatial mode (only for, and default on 2x2 chips) Usage: mlanconfig mlanX hostcmd config/robust_btc.conf mode_get mlanconfig mlanX hostcmd config/robust_btc.conf mode_timeshare mlanconfig mlanX hostcmd config/robust_btc.conf mode_spatial hostcmd generictime hostcmd a2dptime hostcmd inquirytime hostcmd ap_generictime hostcmd ap_a2dptime hostcmd ap_inquirytime This command is used to configure the time slice of COEX (only works in timeshare mode) generictime: configure the Bttime and Wlantime in Station Generic case a2dptime: configure the Bttime and Wlantime in Station A2DP case inquirytime: configure the Bttime and Wlantime in Station Inquiry case ap_generictime: configure the Bttime and Wlantime in Ap Generic case ap_a2dptime: configure the Bttime and Wlantime in Ap A2DP case ap_inquirytime: configure the Bttime and Wlantime in Ap Inquiry case Usage: mlanutl mlanX hostcmd config/robust_btc.conf generictime mlanutl mlanX hostcmd config/robust_btc.conf a2dptime mlanutl mlanX hostcmd config/robust_btc.conf inquirytim mlanutl mlanX hostcmd config/robust_btc.conf ap_generictime mlanutl mlanX hostcmd config/robust_btc.conf ap_a2dptime mlanutl mlanX hostcmd config/robust_btc.conf ap_inquirytime arpfilter This command is used to configure the ARP filtering parameters. Usage: mlanconfig mlanX arpfilter config/arpfilter.conf mefcfg This command is used to set MEF settings. Usage: mlanconfig mlanX mefcfg config/mef.conf cfgdata This command is used to set/get the configuration data to/from firmware. Usage: mlanconfig mlanX cfgdata <.conf file name> This command is used to set the cfg data in the .conf file to firmware. mlanconfig mlanX cfgdata This command is used to get the cfg data from firmware and display on to the console. Where the value of field is: 2 -- Cal data download and <.conf file name> is cal_data.conf setuserscan Initiate a customized scan and retrieve the results Usage: mlanconfig mlanX setuserscan [ARGS] Where [ARGS]: ssid="[SSID]" specify a SSID filter for the scan chan=[chan#][band][mode] where band is [a,b,g,n] and mode is blank for active or 'p' for passive bssid=xx:xx:xx:xx:xx:xx specify a BSSID filter for the scan wc="[WILDCARD SSID]" specify a UNIX pattern matching filter (using * and ?) for SSIDs found in a broadcast probe keep=[0 or 1] keep the previous scan results (1), discard (0) dur=[scan time] time to scan for each channel in milliseconds gap=[time gap] Time gap between two scans in milliseconds probes=[#] number of probe requests to send on each chan for each broadcast probe required and each SSID specific probe required (1-4) type=[1,2,3] BSS type: 1 (Infra), 2(Adhoc), 3(Any) Any combination of the above arguments can be supplied on the command line. If the chan token is absent, a full channel scan will be completed by driver. If the dur or probes tokens are absent, the driver default setting will be used. The bssid and ssid fields, if blank, will produce an unfiltered scan. It's allowed to input multiple ssid/wc entries, the max entry number is 10. The type field will default to 3 (Any) and the keep field will default to 0 (Discard). Examples: 1) Perform an active scan on channels 1, 6, and 11 in the 'g' band: setuserscan chan=1g,6g,11g 2) Perform a passive scan on channel 11 for 20 ms: setuserscan chan=11gp dur=20 3) Perform an active scan on channels 1, 6, and 11; and a passive scan on channel 36 in the 'a' band: setuserscan chan=1g,6g,11g,36ap 4) Perform an active scan on channel 6 and 36 for specific SSID: setuserscan chan=6g,36a ssid=TestAP1 ssid=TestAP2 5) Scan all available channels (B/G/N, A bands) for a specific BSSID, keep the current scan table intact, update existing or append new scan data: setuserscan bssid=00:50:43:20:12:82 keep=1 6) Scan channel 6, for all infrastructure networks, sending two probe requests. Keep the previous scan table intact. Update any duplicate BSSID/SSID matches with the new scan data: setuserscan chan=6g type=1 probes=2 keep=1 7) Scan channel 1 and 6, for all networks matching the Mrvl*AP or AP*Mrvl? patterns and for MrvlTst SSID. Generate 3 broadcast probes for the patterns and 3 SSID specific probes for MrvlTst on both channel 1 and channel 6. setuserscan chan=1g,6g probes=3 wc="Mrvl*AP" wc="AP*Mrvl?" ssid="MrvlTst" 8) Scan all the channels for specified band. setuserscan chan=0g 9) Scan channel 1 and 6, send 3 probe requests, scan each channel for 40 ms with time gap of 50ms between 2 scans setuserscan chan=1g,6g probes=3 dur=40 gap=50 All entries in the scan table (not just the new scan data when keep=1) will be displayed upon completion by use of the getscantable ioctl. getscantable Display the current contents of the driver scan table Usage: mlanconfig mlanX getscantable mlanconfig mlanX getscantable [#] mlanconfig mlanX getscantable tsf mlanconfig mlanX getscantable help 1) Without argument, the entire scantable is displayed. 2) Specifying a # will display detailed information about a specific scan table entry. '0' displays driver cached information regarding the current association (if any). 3) The tsf argument will display the entire scan table with the recorded TSF timestamp for the entry. 4) The help argument will display the legend for the capability field. addts Send an ADDTS command to the associated AP. Process a given conf file for a specific TSPEC data block. Send the TSPEC along with any other IEs to the driver/firmware for transmission in an ADDTS request to the associated AP. Return the execution status of the command as well as the ADDTS response from the AP if any. Usage: mlanconfig mlanX addts delts Send a DELTS command to the associated AP. Process a given conf file for a specific TSPEC data block. Send the TSPEC along with any other IEs to the driver/firmware for transmission in a DELTS request to the associated AP. Return the execution status of the command. There is no response to a DELTS from the AP. Usage: mlanconfig mlanX delts qconfig Send a WMM AC Queue configuration command to get/set/default params Configure or get the parameters of a WMM AC queue. The command takes an optional Queue Id as a last parameter. Without the queue id, all queues will be acted upon. Usage: mlanconfig mlanX qconfig set msdu [Queue Id: 0-3] mlanconfig mlanX qconfig get [Queue Id: 0-3] mlanconfig mlanX qconfig def [Queue Id: 0-3] qstats Turn on/off or retrieve and clear the queue statistics for an AC Turn the queue statistics collection on/off for a given AC or retrieve the current accumulated stats and clear them from the firmware. The command takes an optional Queue Id as a last parameter. Without the queue id, all queues will be acted upon. Usage: mlanconfig mlanX qstats on [Queue Id: 0-3] mlanconfig mlanX qstats off [Queue Id: 0-3] mlanconfig mlanX qstats get [Queue Id: 0-3] qstatus This command retrieves the current status of the WMM queues. If WMM is enabled then it displays the information for each AC in a table. Usage: mlanconfig mlanX qstatus ts_status This command queries the FW for the status of TSIDs 0 through 7 configured via call admission control and displays the results in a table. Usage: mlanconfig mlanX ts_status regrdwr This command is used to read/write the adapter register. Usage: mlanconfig mlanX regrdwr [value] where the parameters are, : 1:MAC/SOC, 2:BBP, 3:RF, 5:CAU : offset of register [value]: value to be written Examples: mlanconfig mlan0 regrdwr 1 0xa060 : Read the MAC register mlanconfig mlan0 regrdwr 1 0xa794 0x80000000 : Write 0x80000000 to MAC register memrdwr This command is used to read/write the adapter memory. Usage: mlanconfig mlanX memrdwr
[value] where the parameters are,
: memory address [value]: value to be written Examples: mlanconfig mlan0 memrdwr 0x80000000 : Read memory address 0x80000000 mlanconfig mlan0 memrdwr 0x80000000 0xffffffff : Write 0xffffffff to memory address 0x80000000 customie This command is used to set or get custom IEs for management frames. Usage : customie [INDEX] [MASK] [IEBuffer] empty - Get all IE settings INDEX: 0 - Get/Set IE index 0 setting 1 - Get/Set IE index 1 setting 2 - Get/Set IE index 2 setting MAX IE Index depends on device memory. -1 - Append/Delete IE automatically Delete will delete the IE from the matching IE buffer Append will append the IE to the buffer with the same mask MASK : Management subtype mask value as per bit definitions : Bit 0 - Association request : Bit 1 - Association response : Bit 2 - Reassociation request : Bit 3 - Reassociation response : Bit 4 - Probe request : Bit 5 - Probe response : Bit 8 - Beacon MASK : MASK = 0 to clear the mask and the IE buffer IEBuffer : IE Buffer in hex (max 256 bytes) The Buffer should not be space separated. Example: ./mlanconfig mlan0 customie Get IE buffer, subtype mask settings for all indices. ./mlanconfig mlan0 customie 1 Get IE buffer and subtype mask for the Index = 1. ./mlanconfig mlan0 customie 2 0 Clear IE buffer and mask value for Index = 2. ./mlanconfig mlan0 customie 3 0x101 0xdd051234567890 Set IE buffer and mask value for Index = 3. ./mlanconfig mlan0 customie -1 0x101 0xdd051234567890 Append the specified IEBuffer at index with mask value of 0x101. ./mlanconfig mlan0 customie -1 0 0xdd051234567890 Delete the specified IEBuffer from all the IEs. ./mlanconfig mlan0 customie 2 0 0xdd051234567890 Delete the specified IEBuffer from the IEs at index 2. tdls_config This command is used to enable/disable TDLS on device. Usage : tdls_config <0/1> 1: Enable TDLS 0: Disable TDLS tdls_setinfo This command is used for setting the capabilities of the TDLS station. Usage : tdls_setinfo Set capabilities of TDLS station. tdls_setup This command is used to send TDLS setup request. Usage: tdls_setup Send TDLS setup request. tdls_discovery This command is used to request TDLS discovery. Usage : tdls_discovery Request TDLS discovery. tdls_teardown This command is used to send TDLS teardown request. Usage : tdls_teardown Request teardown of TDLS link. tdls_powermode This command is used to send TDLS powermode request. Usage : tdls_powermode Send TDLS powermode (either 0:Active, 1:PowerSave) command. tdls_channel_switch This command is used to send TDLS channel switch request. Usage : tdls_channel_switch Send TDLS channel switch command. tdls_stop_channel_switch This command is used to send stop TDLS channel switch request. Usage : tdls_stop_channel_switch Send stop TDLS channel switch command. tdls_cs_params This command is used to set TDLS channel switch params Usage : tdls_cs_params Set TDLS channel switch params. tdls_disable_cs This command is used to disable TDLS channel switch Usage : tdls_disable_cs <0/1> Disable TDLS channel switch. tdls_link_status [peer_mac_address] This command is used to get link information about TDLS links or a TDLS link correponding to peer mac address. Usage : tdls_link_status Send TDLS command to get current link status. tdls_debug This command is used for FW debug functionality and tests. mgmtframetx This command is used to send mgmt frame Usage: mlanconfig mlanX mgmtframetx =============================================================================== U S E R M A N U A L F O R DRIVER COMMAND NAME DRIVER COMMAND - This command is Marvell private command, it can enable and configure Roaming offload and provide the interface between between WPA_Supplicant and the Marvell mdriver SYNOPSIS WPA_CLI: DRIVER SETROAMOFFLOAD data1 WPA_CLI: DRIVER SETROAMOFFLOAD 0/1/2/3/4/5 Enable/Disable Roaming offload with different mode: data1: 0 - disable 1 - enable and wakeup host based on roamOffloadAPlist 2 - enable and ignore the roamOffloadAPlist 3 - based on 2, and reconnect with the same BSSID when disconnect during host suspend 4 - based on 2, and reconnect with the same SSID when disconnect during host suspend 5 - based 0n 2, no roaming and only reconnect the specific BSSID/SSID when disconnect during host suspend WPA_CLI: DRIVER SETROAMOFFLAPLIST data1 [data2] ...... WPA_CLI: DRIVER SETROAMOFFLAPLIST xx:xx:xx:xx:xx:xx Download roaming offload AP list to Driver: xx:xx:xx:xx:xx:xx - the BSSID of AP, one or more than one BSSIDs are allowed. WPA_CLI: DRIVER CFGROAMOFFLOAD [data1 = xx] [data2 = xx] [data3 = xx] [data4 = xx] ..... WPA_CLI: DRIVER CFGROAMOFFLOAD [BSSID = xx:xx:xx:xx:xx:xx] [SSID = marvell_ap] [RETRY_COUNT = 0xff] [MAX_RSSI = 50] [MIN_RSSI=60] [SETP_RSSI = 5] ...... Configure Roaming offload: Note: all parameters are optional. Examples: DRIVER CFGROAMOFFLOAD BSSID = 00:50:43:21:30:ca SSID = marvell_ap RETRY_COUNT = 0xff MAX_RSSI = 50 =============================================================================== U S E R M A N U A L F O R M L A N 2 0 4 0 C O E X NAME mlan2040coex - This application handles the 11n 20/40 coexistence operation for the Marvell mdriver SYNOPSIS mlan2040coex [-d ] [-i ] [hvB] -d = Device number (n) -i = Interface name (intfname) -h = Help -v = Version -B = Run the process in background Note: If device number (n) is not present, then 0 assumed. If intfname is not present, then mlan0 assumed. =============================================================================== U S E R M A N U A L F O R MLANEVENT NAME mlanevent.exe This tool can be used to listen for and obtain events from the driver through the netlink layer. ---------------- Supported events ---------------- STA_DEAUTH STA_ASSOC BSS_START BSS_IDLE BSS_ACTIVE ----------------- Details of events ----------------- STA_DEAUTH ---------- For this event, the following information is shown: + Deauthenticated STA MAC address. + Reason for deauthentication. STA_ASSOC ---------- For this event, the following information is shown: + STA MAC address. BSS_START ---------- For this event, the following information is shown: + AP MAC address. BSS_IDLE ---------- For this event, there is no associated information. BSS_ACTIVE ---------- For this event, there is no associated information. ===============================================================================