diff --git a/README b/README
index 77a7064..2b0a47c 100755
--- a/README
+++ b/README
@@ -1,5 +1,3 @@
-# MXM
-
 ===============================================================================
 			U S E R  M A N U A L
 
@@ -8,60 +6,31 @@
 
 1) FOR DRIVER BUILD
 
-	Goto source code directory.
+	Goto source code directory wlan_src/.
 	make [clean] build
-	The driver and utility binaries can be found in bin_wlan directory.
+	The driver and utility binaries can be found in ../bin_xxxx directory.
 	The driver code supports Linux kernel from 2.6.32 to 6.7.0.
 
 2) FOR DRIVER INSTALL
 
-#ifdef MULTI_CHIP
 	a) Copy firmware image to /lib/firmware/nxp/, copy wifi_mod_para.conf to /lib/firmware/nxp/.
 	b) Install WLAN driver
 	   There are drv_mode, max_sta_bss, max_uap_bss etc. module parameters.
 		The bit settings of drv_mode are,
 			Bit 0 :  STA
 			Bit 1 :  uAP
-#ifdef WIFI_DIRECT_SUPPORT
 			Bit 2 :  WIFIDIRECT
-#endif
-#ifdef MPL_SUPPORT
-			Bit 3 :  MPL
-#endif
-#ifdef NAN_SUPPORT
 			Bit 4 :  NAN
-#endif
 
-#ifdef ADHOC_OVER_IP
-		max_sta_bss: Maximum number of STA BSS (default 1, max 18)
-#else
-#ifdef STA_MBSS_SUPPORT
-		max_sta_bss: Maximum number of STA BSS (default 1, max 2)
-#else
 		max_sta_bss: Maximum number of STA BSS (default 1, max 1)
-#endif
-#endif
 		sta_name: Name of the STA interface (default: "mlan")
-#ifdef UAP_MBSS_SUPPORT
 		max_uap_bss: Maximum number of uAP BSS (default 1, max 2)
-#else
-		max_uap_bss: Maximum number of uAP BSS (default 1, max 1)
-#endif
 		uap_name: Name of the uAP interface (default: "uap")
-#ifdef WIFI_DIRECT_SUPPORT
 		max_wfd_bss: Maximum number of WIFIDIRECT BSS (default 1, max 1)
 		wfd_name: Name of the WIFIDIRECT interface (default: "wfd")
-#if defined(STA_CFG80211) && defined(UAP_CFG80211)
 		max_vir_bss: Number of Virtual interfaces (default 0)
-#endif
-#endif
-#ifdef MPL_SUPPORT
-		max_mpl_bss: Number of MPL interfaces (defaut 1, max 1)
-#endif
-#ifdef NAN_SUPPORT
 		nan_name: Name of the NAN interface (default: "nan")
 		max_nan_bss: Number of NAN interfaces (default 1)
-#endif
 		uap_oper_ctrl: uAP operation control when in-STA disconnect with ext-AP
                                0: default do nothing, 2: uAP stops and restarts automatically
 	   For example, to install multi-chip driver,
@@ -74,495 +43,69 @@
 		ifconfig uapX down
 		rmmod moal
 		rmmod mlan
-#else
-#ifdef USB      // Section 1	USB
-#ifdef UAP_STA_SUPPORT
-#ifdef ORION
-	a) Copy firmware image usb8786_uapsta.bin | ... to /usr/lib/hotplug/firmware/nxp/
-	   directory, create the directory if it doesn't exist.
-#else
-	a) Copy firmware image usb8766_uapsta.bin | ... to /lib/firmware/nxp/ directory,
-	   create the directory if it doesn't exist.
-#endif
-	b) Install WLAN driver
-	   There are drv_mode, max_sta_bss, max_uap_bss etc. module parameters.
-		The bit settings of drv_mode are,
-			Bit 0 :  STA
-			Bit 1 :  uAP
-#ifdef WIFI_DIRECT_SUPPORT
-			Bit 2 :  WIFIDIRECT
-#endif
-#ifdef MPL_SUPPORT
-			Bit 3 :  MPL
-#endif
-#ifdef NAN_SUPPORT
-			Bit 4 :  NAN
-#endif
 
-#ifdef ADHOC_OVER_IP
-		max_sta_bss: Maximum number of STA BSS (default 1, max 18)
-#else
-#ifdef STA_MBSS_SUPPORT
-		max_sta_bss: Maximum number of STA BSS (default 1, max 2)
-#else
-		max_sta_bss: Maximum number of STA BSS (default 1, max 1)
-#endif
-#endif
-		sta_name: Name of the STA interface (default: "mlan")
-#ifdef UAP_MBSS_SUPPORT
-		max_uap_bss: Maximum number of uAP BSS (default 1, max 2)
-#else
-		max_uap_bss: Maximum number of uAP BSS (default 1, max 1)
-#endif
-		uap_name: Name of the uAP interface (default: "uap")
-#ifdef WIFI_DIRECT_SUPPORT
-		max_wfd_bss: Maximum number of WIFIDIRECT BSS (default 1, max 1)
-		wfd_name: Name of the WIFIDIRECT interface (default: "wfd")
-#if defined(STA_CFG80211) && defined(UAP_CFG80211)
-		max_vir_bss: Number of Virtual interfaces (default 0)
-#endif
-#endif
-#ifdef MPL_SUPPORT
-		max_mpl_bss: Number of MPL interfaces (defaut 1, max 1)
-#endif
-#ifdef NAN_SUPPORT
-		nan_name: Name of the NAN interface (default: "nan")
-		max_nan_bss: Number of NAN interfaces (default 1)
-#endif
-		uap_oper_ctrl: uAP operation control when in-STA disconnect with ext-AP
-                               0: default do nothing, 2: uAP stops and restarts automatically
-#ifdef USBXXX
-	   For example, to install USB multi-chip driver,
-		insmod mlan.ko
-		insmod usbxxx.ko mod_para=nxp/wifi_mod_para.conf [drvdbg=0x7]
-	   wifi_mod_para.conf is used to support multi-chips which has different load module parameters. It contains
-           the module parameters for different chips.
-#else
-	   For example, to install USB8766 driver,
-		insmod mlan.ko
-		insmod usb8766.ko [drv_mode=3] [fw_name=nxp/usb8766_uapsta.bin]
-	   To load driver in STA only mode,
-		insmod mlan.ko
-		insmod usb8766.ko drv_mode=1 [fw_name=nxp/usb8766_uapsta.bin]
-	   To load driver in uAP only mode,
-		insmod mlan.ko
-		insmod usb8766.ko drv_mode=2 [fw_name=nxp/usb8766_uapsta.bin]
-#ifdef USB_FW_DNLD_ENH
-	   To load driver with wifi downloader firmware support.
-		insmod mlan.ko
-		insmod usb8997.ko usb_fw_option=1 cal_data_cfg=...
-#endif
-#endif // USBXXX
-	   To switch mode between STA only, uAP only and uAPSTA in run time,
-		echo drv_mode=1 > /proc/mwlan/adapterX/config		// STA mode
-		echo drv_mode=2 > /proc/mwlan/adapterX/config		// uAP mode
-		echo drv_mode=3 > /proc/mwlan/adapterX/config		// uAPSTA mode
-	c) Uninstall WLAN driver,
-		ifconfig mlanX down
-		ifconfig uapX down
-		rmmod usbxxx
-		rmmod mlan
-#else
-#ifdef ORION
-	a) Copy firmware image usb8786.bin | ... to /usr/lib/hotplug/firmware/nxp/
-	   directory, create the directory if it doesn't exist.
-#else
-	a) Copy firmware image usb8766.bin | ... to /lib/firmware/nxp/ directory,
-	   create the directory if it doesn't exist.
-#endif
-	b) Install WLAN driver,
-#ifdef USBXXX
-	   For example, to install multi-chip driver,
-		insmod mlan.ko
-		insmod usbxxx.ko mod_para=nxp/wifi_mod_para.conf [drvdbg=0x7]
-	   wifi_mod_para.conf is used to support multi chips which has different module parameters. It contains
-           the module parameters for different chips.
-#else
-	   For example, to install USB8766 driver,
-		insmod mlan.ko
-		insmod usb8766.ko [fw_name=nxp/usb8766.bin]
-#endif //USBXXX
-	c) Uninstall WLAN driver,
-		ifconfig mlan0 down
-		rmmod usbxxx
-		rmmod mlan
-#endif // UAP_STA_SUPPORT
-#endif          // End of section 1	USB
-
-#ifdef SDIO     // Section 2	SDIO
-#ifdef UAP_STA_SUPPORT
-#ifdef PXA9XX
-	a) Copy firmware image sd8787_uapsta.bin | sd8797_uapsta.bin | ... to
-	   /system/etc/firmware/nxp/ directory, create the directory if it doesn't exist.
-#else
-	a) Copy firmware image sd8787_uapsta.bin | sd8797_uapsta.bin | ... to
-	   /lib/firmware/nxp/ directory, create the directory if it doesn't exist.
-#endif
-#ifdef SYSKT_MULTI
-	b) Install SDIO bus driver and WLAN driver,
-		./load sd8787 | sd8797 | ...
-	   Update load script to specify drv_mode, max_sta_bss, max_uap_bss etc. parameters.
-#else
-	b) Install WLAN driver,
-	   There are drv_mode, max_sta_bss, max_uap_bss etc. module parameters.
-#endif
-		The bit settings of drv_mode are,
-			Bit 0 :  STA
-			Bit 1 :  uAP
-#ifdef WIFI_DIRECT_SUPPORT
-			Bit 2 :  WIFIDIRECT
-		The default drv_mode is 7.
-#else
-		The default drv_mode is 3.
-#endif
-#ifdef MPL_SUPPORT
-			Bit 3 :  MPL
-#endif
-#ifdef NAN_SUPPORT
-			Bit 4 :  NAN
-#endif
-
-#ifdef ADHOC_OVER_IP
-		max_sta_bss: Maximum number of STA BSS (default 1, max 18)
-#else
-#ifdef STA_MBSS_SUPPORT
-		max_sta_bss: Maximum number of STA BSS (default 1, max 2)
-#else
-		max_sta_bss: Maximum number of STA BSS (default 1, max 1)
-#endif
-#endif
-		sta_name: Name of the STA interface (default: "mlan")
-#ifdef UAP_MBSS_SUPPORT
-		max_uap_bss: Maximum number of uAP BSS (default 1, max 2)
-#else
-		max_uap_bss: Maximum number of uAP BSS (default 1, max 1)
-#endif
-		uap_name: Name of the uAP interface (default: "uap")
-#ifdef WIFI_DIRECT_SUPPORT
-		max_wfd_bss: Maximum number of WIFIDIRECT BSS (default 1, max 1)
-		wfd_name: Name of the WIFIDIRECT interface (default: "wfd")
-#if defined(STA_CFG80211) && defined(UAP_CFG80211)
-		max_vir_bss: Number of Virtual interfaces (default 0)
-#endif
-#endif
-#ifdef MPL_SUPPORT
-		max_mpl_bss: Number of MPL interfaces (defaut 1, max 1)
-#endif
-#ifdef NAN_SUPPORT
-		nan_name: Name of the NAN interface (default: "nan")
-		max_nan_bss: Number of NAN interfaces (default 1)
-#endif
-#ifdef SDIOXXX
-	   For example, to install multi-chip driver,
-		insmod mlan.ko
-		insmod sdxxx.ko mod_para=nxp/wifi_mod_para.conf [drvdbg=0x7]
-	   wifi_mod_para.conf is used to support multi chips which has different module parameters. It contains
-	   the module parameters for different chips.
-#else
-#ifdef SYSKT_MULTI
-	   For example, load driver in STA only mode,
-		...
-		insmod $1.ko drv_mode=1 [fw_name=nxp/sd8887_uapsta.bin]
-#else
-	   For example, to install SD8887 driver,
-		insmod mlan.ko
-		insmod sd8887.ko [drv_mode=3] [fw_name=nxp/sd8887_uapsta.bin]
-	   To load driver in STA only mode,
-		insmod mlan.ko
-		insmod sd8887.ko drv_mode=1 [fw_name=nxp/sd8887_uapsta.bin]
-	   To load driver in uAP only mode,
-		insmod mlan.ko
-		insmod sd8887.ko drv_mode=2 [fw_name=nxp/sd8887_uapsta.bin]
-#endif
-#endif //SDIOXXX
-
-	   To switch mode between STA only, uAP only and uAPSTA etc. in run time,
-		echo drv_mode=1 > /proc/mwlan/adapterX/config		// STA mode
-		echo drv_mode=2 > /proc/mwlan/adapterX/config		// uAP mode
-		echo drv_mode=3 > /proc/mwlan/adapterX/config		// STA+uAP mode
-#ifdef WIFI_DIRECT_SUPPORT
-		echo drv_mode=7 > /proc/mwlan/adapterX/config		// STA+uAP+WIFIDIRECT mode
-#endif
-#ifdef SYSKT_MULTI
-	c) Uninstall WLAN driver and SDIO bus driver,
-		./unload
-#else
-	c) Uninstall WLAN driver,
-		ifconfig mlanX down
-		ifconfig uapX down
-		rmmod sdxxx
-		rmmod mlan
-#endif
-#else
-	a) Copy sd8787.bin | ... to /lib/firmware/nxp/ directory,
-	   create the directory if it doesn't exist.
-#ifdef SDIOXXX
-	b) Install SDIO bus driver and WLAN driver,
-	   For example, to install multi-chip driver,
-		insmod mlan.ko
-		insmod sdxxx.ko mod_para=nxp/wifi_mod_para.conf [drvdbg=0x7]
-	   wifi_mod_para.conf is used to support multi chips which has different module parameters. It contains
-	   the module parameters for different chips.
-	c) Uninstall WLAN driver,
-		ifconfig mlanX down
-		rmmod sdxxx
-		rmmod mlan
-#else
-#ifdef SYSKT_MULTI
-	b) Install SDIO bus driver and WLAN driver,
-		./load sd8787 | ...
-	c) Uninstall WLAN driver and SDIO bus driver,
-		./unload
-#else
-#ifdef ENT_BUILD
-	b) Install WLAN driver,
-		insmod mlan_ent.ko
-		insmod sdxxx_ent.ko [fw_name=nxp/sd8xxx.bin]
-	c) Uninstall WLAN driver,
-		ifconfig mlanX down
-		rmmod sdxxx_ent
-		rmmod mlan_ent
-#else
-	b) Install WLAN driver,
-		insmod mlan.ko
-		insmod sdxxx.ko [fw_name=nxp/sd8xxx.bin]
-	c) Uninstall WLAN driver,
-		ifconfig mlanX down
-		rmmod sdxxx
-		rmmod mlan
-#endif // ENT_BUILD
-#endif // SYSKT_MULTI
-#endif // SDIOXXX
-#endif // UAP_STA_SUPPORT
-#endif          // End of section 2	SDIO
-
-#ifdef PCIE     // Section 4	PCIe
-#ifdef UAP_STA_SUPPORT
-	a) Copy firmware image pcie8897_uapsta.bin | ... to /lib/firmware/nxp/ directory,
-	   create the directory if it doesn't exist.
-	b) Install WLAN driver
-	   There are drv_mode, max_sta_bss, max_uap_bss etc. module parameters.
-		The bit settings of drv_mode are,
-			Bit 0 :  STA
-			Bit 1 :  uAP
-#ifdef WIFI_DIRECT_SUPPORT
-			Bit 2 :  WIFIDIRECT
-#endif
-#ifdef MPL_SUPPORT
-			Bit 3 :  MPL
-#endif
-#ifdef NAN_SUPPORT
-			Bit 4 :  NAN
-#endif
-
-#ifdef ADHOC_OVER_IP
-		max_sta_bss: Maximum number of STA BSS (default 1, max 18)
-#else
-#ifdef STA_MBSS_SUPPORT
-		max_sta_bss: Maximum number of STA BSS (default 1, max 2)
-#else
-		max_sta_bss: Maximum number of STA BSS (default 1, max 1)
-#endif
-#endif
-		sta_name: Name of the STA interface (default: "mlan")
-#ifdef UAP_MBSS_SUPPORT
-		max_uap_bss: Maximum number of uAP BSS (default 1, max 2)
-#else
-		max_uap_bss: Maximum number of uAP BSS (default 1, max 1)
-#endif
-		uap_name: Name of the uAP interface (default: "uap")
-#ifdef WIFI_DIRECT_SUPPORT
-		max_wfd_bss: Maximum number of WIFIDIRECT BSS (default 1, max 1)
-		wfd_name: Name of the WIFIDIRECT interface (default: "wfd")
-#if defined(STA_CFG80211) && defined(UAP_CFG80211)
-		max_vir_bss: Number of Virtual interfaces (default 0)
-#endif
-#endif
-#ifdef MPL_SUPPORT
-		max_mpl_bss: Number of MPL interfaces (defaut 1, max 1)
-#endif
-#ifdef NAN_SUPPORT
-		nan_name: Name of the NAN interface (default: "nan")
-		max_nan_bss: Number of NAN interfaces (default 1)
-#endif
-#ifdef PCIEXXX
-	   For example, to install multi-chip driver,
-		insmod mlan.ko
-		insmod pciexxx.ko mod_para=nxp/wifi_mod_para.conf [drvdbg=0x7]
-	   wifi_mod_para.conf is used to support multi chips which has different module parameters. It contains
-	   the module parameters for different chips.
-#else
-	   For example, to install PCIE8897 driver,
-		insmod mlan.ko
-		insmod pcie8897.ko [drv_mode=3] [fw_name=nxp/pcie8897_uapsta.bin]
-	   To load driver in STA only mode,
-		insmod mlan.ko
-		insmod pcie8897.ko drv_mode=1 [fw_name=nxp/pcie8897_uapsta.bin]
-	   To load driver in uAP only mode,
-		insmod mlan.ko
-		insmod pcie8897.ko drv_mode=2 [fw_name=nxp/pcie8897_uapsta.bin]
-#endif // PCIEXXX
-
-	   To switch mode between STA only, uAP only and uAPSTA in run time,
-		echo drv_mode=1 > /proc/mwlan/adapterX/config		// STA mode
-		echo drv_mode=2 > /proc/mwlan/adapterX/config		// uAP mode
-		echo drv_mode=3 > /proc/mwlan/adapterX/config		// uAPSTA mode
-	c) Uninstall WLAN driver,
-		ifconfig mlanX down
-		ifconfig uapX down
-		rmmod pciexxx
-		rmmod mlan
-#endif // UAP_STA_SUPPORT
-#endif          // End of section 4	PCIe
-#endif // MULTI_CHIP
-
-#ifdef MFG_CMD_SUPPORT
 	To load driver with MFG firmware file, use mfg_mode=1 when insmod WLAN driver and
 	specify MFG firmware name if needed.
-#endif
 
-#ifdef RF_TEST_MODE
 	To load driver with rf_test firmware file, use rf_test_mode=1 when insmod WLAN driver.
 	This parameter only used for 9177(FC)
-#endif
 
 	There are some other parameters for debugging purpose etc. Use modinfo to check details.
-#ifdef DEBUG_LEVEL1
 	  drvdbg=<bit mask of driver debug message control>
-#ifdef DEBUG_LOG
-	  logctrl=<Bit mask of driver log message control>
-	  sh_mem_size=<Shared memory length (default 8192 bytes)>
-#endif
-#endif
 	  dev_cap_mask=<Bit mask of the device capability>
 	  mac_addr=xx:xx:xx:xx:xx:xx <override the MAC address (in hex)>
-#if defined(OPTIMIZED_PS) && defined(DEEP_SLEEP)
 	  auto_ds=0|1|2 <use MLAN default | enable auto deepsleep | disable auto deepsleep>
-#endif
-#if defined(EXT_SCAN_SUPPORT) && defined(EXT_SCAN_ENH)
 	  ext_scan=0|1|2 <use MLAN default | Enable Extended Scan| Enable Enhanced Extended Scan>
-#endif
       net_rx=0|1 <use netif_rx_ni in rx | use netif_receive_skb in rx>
       amsdu_deaggr=0|1 <default | Try avoid buf copy in amsud deaggregation>
 
-#ifdef ENABLE_802_11P
-	  max_11p_bss = <Max number of 802_11P interfaces (default 1)>
-#endif
 	  ps_mode=0|1|2 <use MLAN default | enable IEEE PS mode | disable IEEE PS mode>
 	  sched_scan=0|1 <disable sched_scan | enable sched_scan default>
 	  max_tx_buf=2048|4096|8192 <maximum AMSDU Tx buffer size>
-#ifdef SDIO_SUSPEND_RESUME
 	  pm_keep_power=1|0 <PM keep power in suspend (default) | PM no power in suspend>
 	  shutdown_hs=1|0 <Enable HS when shutdown | No HS when shutdown (default)>
-#endif
-#ifdef ENABLE_802_11D
 	  cfg_11d=0|1|2 <use MLAN default | enable 11d | disable 11d>
-#endif
-#ifdef CONFIG_OF
 	  dts_enable=0|1 <Disable DTS | Enable DTS (default)>
-#endif
-#ifdef FW_DNLD_NEEDED
 	  fw_name = <FW file name>
 		e.g. copy pcieuart9098_combo_v1.bin to firmware directory, fw_name=nxp/pcieuart9098_combo_v1.bin
-#endif
 	  hw_name = <hardware name>
 	  reg_work=0|1 <Disable register work queue| Enable register work queue>
 	  hw_test=0|1 <Disable hardware test (default) | Enable hardware test>
 	  fw_serial=0|1 <support parallel download FW | support serial download FW (default)>
 	  req_fw_nowait=0|1 <use request_firmware API (default) | use request_firmware_nowait API>
-#if !defined(MLANUTL_LITE)
-#ifdef DFS_SUPPORT
       dfs53cfg=0|1|2 <use Fw Default | New W53 | Old W53>
-#endif
 	  mcs32=0|1 <disable HT MCS32 support | enable HT MCS32 (default)>
-#ifdef SDIOXXX
 	  SD8887: antcfg=0|1|2|0xffff <default | Tx/Rx antenna 1 | Tx/Rx antenna 2 | enable antenna diversity>
 	  SD8897/SD8997: antcfg=0x11|0x13|0x33 <Bit0:Rx Path A, Bit1:Rx Path B, Bit 4:Tx Path A, Bit 5:Tx Path B>
-#else
-#ifdef SD8887
-	  antcfg=0|1|2|0xffff <default | Tx/Rx antenna 1 | Tx/Rx antenna 2 | enable antenna diversity>
-#else
-#if defined(SD8897) || defined(SD8997)||defined(SD9098) ||defined(SD9097)||defined(SDIW624)
-	  antcfg=0x11|0x13|0x33 <Bit0:Rx Path A, Bit1:Rx Path B, Bit 4:Tx Path A, Bit 5:Tx Path B>
-#endif
-#endif
-#endif
-#endif /* !defined(MLANUTL_LITE) */
-#ifdef SDIO
 	  slew_rate: Slew Rate Control value = 0|1|2|3 (0 is the slowest slew rate and 03 has the highest slew rate (default))
-#endif
-#ifdef NO_EEPROM_SUPPORT
 	  init_cfg=<init config (MAC addresses, registers etc.) file name>
 		e.g. copy init_cfg.conf to firmware directory, init_cfg=nxp/init_cfg.conf
 	  cal_data_cfg=<CAL data config file name>
 		e.g. copy cal_data.conf to firmware directory, cal_data_cfg=nxp/cal_data.conf
-#if defined(SDIOXXX) || defined(SD8887)
           Note: Loading driver with 8887 must include correct cal_data_cfg parameter.
-#endif
-#endif
-#ifdef NO_EEPROM_SUPPORT
 	 dpd_data_cfg=<DPD data config file name>
 	   e.g. copy dpd_data.conf to firmware directory, dpd_data_cfg=nxp/dpd_data.conf
-#endif
-#ifdef TX_POWERCFG
 	  txpwrlimit_cfg=<Tx power limit config file name>
 		e.g. copy txpwrlimit_cfg_set.conf to firmware directory, txpwrlimit_cfg=nxp/txpwrlimit_cfg_set.conf
 		txpwrlimit_cfg_set.conf file should be the binary format file generate by mlanutl application
 
-#ifdef OTP_CHANINFO
       cntry_txpwr=0|1|2
-#else
-      cntry_txpwr=0|1
-#endif
                   0: Disable setting tx power table of country (default)
                   1: Enable setting tx power table of country
-#ifdef OTP_CHANINFO
                   2: Enable setting rgpower table of country
-#endif
-#endif
-#ifdef HOSTCMD_CFG
 	  init_hostcmd_cfg=<init hostcmd config file name>
 		e.g. copy init_hostcmd_cfg.conf to firmware directory, init_hostcmd_cfg=nxp/init_hostcmd_cfg.conf
 	  band_steer_cfg=<band steer config file name>
 		e.g. generate bscfg.conf by band_steer_cfg.conf, then copy bscfg.conf to firmware directory, band_steer_cfg=nxp/bscfg.conf
-#endif
-#if defined(SYSKT_MULTI) && defined(OOB_WAKEUP)
-	  oob_mode=0|1 <disable OOB wakeup mode (default) | enable OOB wakeup mode>
-#endif
-#ifdef SUSPEND_SDIO_PULL_DOWN
-	  sdio_pd=0|1 <disable suspend with sdio pull down feature (default) | enable suspend with sdio pull down feature>
-#endif
-#ifdef SDIO_SP_RX_AGGR
 	  sdio_rx_aggr=1|0 <Enable SDIO rx aggr (default) | Disable SDIO rx aggr>
-#endif
-#ifdef T3T
-#ifdef SDIO
-	  minicard_pwrup=1|0 <power up/down on driver load/unload (default) | don't power up/down>
-#endif
-#endif
-#ifdef SIMU_CFG80211_WEXT
 	  cfg80211_wext=<bit mask of CFG80211 and WEXT control>
-#ifdef STA_WEXT
 		Bit 0: STA WEXT
-#endif
-#ifdef UAP_WEXT
 		Bit 1: uAP WEXT
-#endif
-#ifdef STA_CFG80211
 		Bit 2: STA CFG80211
-#endif
-#ifdef UAP_CFG80211
 		Bit 3: uAP CFG80211
-#endif
-#endif
-#ifdef MULTI_CHAN_SUPPORT
 	  cfg80211_drcs=1|0 <Enable DRCS support (default) | Disable DRCS support>
-#endif
 	  reg_alpha2=<Regulatory alpha2 (default NULL)>
-#ifdef USB_NEW_FW_DNLD
 	  skip_fwdnld=0|1 <enable FW download support (default) | disable FW download support>
-#endif
-#ifdef WORK_QUEUE
 	  wq_sched_prio: Priority for work queue
 	  wq_sched_policy: Scheduling policy for work queue
 		(0: SCHED_NORMAL, 1: SCHED_FIFO, 2: SCHED_RR, 3: SCHED_BATCH, 5: SCHED_IDLE)
@@ -570,109 +113,41 @@
 		as module parameters. If wq_sched_policy is (0, 3 or 5), then wq_sched_prio
 		must be 0. wq_sched_prio should be 1 to 99 otherwise.
 	  rx_work=0|1|2 <default | Enable rx_work_queue | Disable rx_work_queue>
-#endif
-#ifdef PCIE
-#if defined(PCIE) && defined(PCIE_MSIX)
 	  pcie_int_mode=0|1|2 <Legacy mode, MSI mode (default), MSI-X mode>
-#elif defined(PCIE_MSI)
 	  pcie_int_mode=0|1 <Legacy mode, MSI mode (default)>
-#else
-	  pcie_int_mode=0 <Legacy mode(default)>
-#endif
-#if defined(PCIE9098) ||defined(PCIE9097)||defined(PCIEIW624)
       ring_size=32|64|128|256|512 <adma ring size for 9097/9098>
-#endif
-#endif
-#if !defined(MLANUTL_LITE)
-#ifdef AGGR_CTRL
 	  aggrctrl=1|0 <enable Tx aggr | disable Tx aggr>
-#endif
-#endif /* !defined(MLANUTL_LITE) */
-#if defined(USB_TX_AGGR) || defined(USB_RX_DEAGGR)
 	  usb_aggr=0|1|2 <use MLAN default (disabled) | enable USB aggr | disable USB aggr>
-#endif
-#if defined WLAN_LOW_POWER_ENABLE
 	  low_power_mode_enable=0|1 <disable low power mode (default)| enable low power mode>
 	  When low power mode is enabled, the output power will be clipped at ~+10dBm and the
 	  expected PA current is expected to be in the 80-90 mA range for b/g/n modes
-#endif
-#if defined(ANDROID_KERNEL)
-#ifdef T50
-	wakelock_timeout=<set wakelock_timeout value (ms),default 3000ms>
-#else
 	wakelock_timeout=<set wakelock_timeout value (ms)>
-#endif
-#endif
-#ifdef V16_FW_API
 	pmic=0|1 <No pmic configure cmd sent to firmware | Send pmic configure cmd to firmware>
-#endif
-#ifdef HS_SUPPORT
 	indication_gpio=0xXY <GPIO to indicate wakeup source and its level; high four bits X:
                   level(0/1) for normal wakeup; low four bits Y: GPIO pin number. This parameter
                   only works with specific board and firmware.>
 	hs_wake_interval=<Host sleep wakeup interval,it will round to nearest multiple dtim*beacon_period in fw>
 	disconnect_on_suspend=0|1 <Disable disconnect wifi on suspend (default) | Enable disconnect wifi on suspend>
-#ifdef HS_MIMO_SWITCH
 	hs_mimo_switch=0|1 <Disable dynamic MIMO-SISO switch during host sleep (default) | Enable dynamic MIMO-SISO switch during host sleep>
-#endif
-#endif
-#if defined(HS_SUPPORT) || defined(UAP_HS_SUPPORT)
     hs_auto_arp=0|1 <disable hs_auto_arp (default) | enable hs_auto_arp>
-#endif
-#ifdef GTK_REKEY_OFFLOAD
 	gtk_rekey_offload=0|1|2 <disable gtk_rekey_offload|enable gtk_rekey_offload (default) | enable gtk_rekey_offload in suspend mode only>
-#endif
-#ifdef NAPI_SUPPORT
 	napi=0|1 <disable napi | enable napi>
-#endif
 	fixed_beacon_buffer=0|1 <allocate default buffer size (default) | allocate max buffer size>
-#ifdef WIFI_DIRECT_SUPPORT
 	GoAgeoutTime=0|x <use default ageout time (default) | set Go age out time xTU(TU 100ms)>
-#endif
 	multi_dtim=0|x <use default DTIM interval(default) | set x*beacon_period as DTIM interval>
 	inact_tmo=0|x <use default IEEE ps inactivity timout value (default) | use IEEE ps inactivity timeout value x ms>
-#ifdef MULTI_CHAN_SUPPORT
 	drcs_chantime_mode=0|x <channel time and mode for DRCS, use default value (default) | use setting value>
 	  Bit31~Bit24:Channel time for channel index0;
 	  Bit23~Bit16:mode for channel index0; 0|1 <PM1 | Null2Self>
 	  Bit15~Bit8:Channel time for channel index1;
 	  Bit7~Bit0:mode for channel index1; 0|1 <PM1 | Null2Self>
-#endif
-#ifdef FW_ROAMING
 	roamoffload_in_hs=0|1 <always enable fw roaming (default) | enable fw roaming only when host suspend>
-#endif
-#ifdef MAX_STA_SIXTY_FOUR
 	uap_max_sta: Maximum number of STA for UAP/GO (default 0, max 64)
-#else
-#ifdef MAX_STA_THIRTY_TWO
-	uap_max_sta: Maximum number of STA for UAP/GO (default 0, max 32)
-#else
-#ifdef MAX_STA_TWENTY
-	uap_max_sta: Maximum number of STA for UAP/GO (default 0, max 20)
-#else
-#ifdef MAX_STA_TEN
-	uap_max_sta: Maximum number of STA for UAP/GO (default 0, max 10)
-#else
-#ifdef MAX_STA_FIVE
-	uap_max_sta: Maximum number of STA for UAP/GO (default 0, max 5)
-#else
-	uap_max_sta: Maximum number of STA for UAP/GO (default 0, max 8)
-#endif
-#endif
-#endif
-#endif
-#endif
-#ifdef HOST_MLME
-#if defined(STA_CFG80211) || defined(UAP_CFG80211)
 	host_mlme=0|1 <Operate in non-host_mlme mode | Operate in host_mlme mode (default)>
 	for supplicant/authenticator running on host side, WPA3 support is available only in host_mlme mode
 	for chipset 89xx FP-92, 90xx and later, host_mlme restricted to 1
-#endif
-#endif
-#if defined(STA_CFG80211) || defined(UAP_CFG80211)
 	country_ie_ignore=0|1 <Follow countryIE from AP and beacon hint enable (default) | Ignore countryIE from AP and beacon hint disable>
 	beacon_hints=0|1 <enable beacon hints(default) | disable beacon hints>
-#endif
 
 	chan_track=0|1 <restore channel tracking parameters(default) | set channel tracking new parameters> for 9098 only
 	keep_previous_scan=0|1, <Flush previous scan result before start scan | Keep previous scan result(default)>
@@ -733,9 +208,7 @@
 	The following debug info are provided in /proc/net/mwlan/adapterX/mlanY|uapY|wfdY/debug,
 	on kernel 2.6.24 or later, the entry is /proc/mwlan/adapterX/mlanY|uapY|wfdY/debug.
 
-#ifdef DEBUG_LEVEL1
 	drvdbg = <bit mask of driver debug message control>
-#endif
 	wmm_ac_vo = <number of packets sent to device from WMM AcVo queue>
 	wmm_ac_vi = <number of packets sent to device from WMM AcVi queue>
 	wmm_ac_be = <number of packets sent to device from WMM AcBE queue>
@@ -744,30 +217,16 @@
 	tx_buf_size = <current Tx buffer size>
 	curr_tx_buf_size = <current Tx buffer size in FW>
 	ps_mode = <0/1, CAM mode/PS mode>
-#ifdef OPTIMIZED_PS
 	ps_state = <0/1/2/3, awake state/pre-sleep state/sleep-confirm state/sleep state>
-#else
-	ps_state = <0/1/2/3, full power state/awake state/pre-sleep state/sleep state>
-#endif
-#ifdef DEEP_SLEEP
 	is_deep_sleep = <0/1, not deep sleep state/deep sleep state>    // Only for STA
-#endif
-#if defined(HS_SUPPORT)
 	wakeup_dev_req = <0/1, wakeup device not required/required>
-#endif
-#if defined(HS_SUPPORT) || defined(DEEP_SLEEP)
 	wakeup_tries = <wakeup device count, cleared when device awake>
-#endif
-#ifdef HS_SUPPORT
 	hs_configured = <0/1, host sleep not configured/configured>
 	hs_activated = <0/1, extended host sleep not activated/activated>
-#endif
 	tx_pkts_queued = <number of Tx packets queued>
-#ifdef WMM_UAPSD
 	pps_uapsd_mode = <0/1, PPS/UAPSD mode disabled/enabled>     // Only for STA
 	sleep_pd = <sleep period in milliseconds>                   // Only for STA
 	qos_cfg = <WMM QoS info>                                    // Only for STA
-#endif
 	tx_lock_flag = <0/1, Tx lock flag>                          // Only for STA
 	port_open = <0/1, port open flag>                           // Only for STA
 	scan_processing = <0/1, scan processing flag>               // Only for STA
@@ -787,12 +246,10 @@
 	num_cmd_h2c_fail = <number of commands failed to send to device>
 	num_cmd_sleep_cfm_fail = <number of sleep confirm failed to send to device>
 	num_tx_h2c_fail = <number of data packets failed to send to device>
-#ifdef SDIO
 	num_cmdevt_c2h_fail = <number of commands/events failed to receive from device>
 	num_rx_c2h_fail = <number of data packets failed to receive from device>
 	num_int_read_fail = <number of interrupt read failures>
 	last_int_status = <last interrupt status>
-#endif
 	num_evt_deauth = <number of deauthenticated events received from device>        // Only for STA
 	num_evt_disassoc = <number of disassociated events received from device>        // Only for STA
 	num_evt_link_lost = <number of link lost events received from device>           // Only for STA
@@ -805,45 +262,31 @@
 	curr_rd_port = <SDIO multi-port current read port>
 	mp_wr_bitmap = <SDIO multi-port write bitmap>
 	curr_wr_port = <SDIO multi-port current write port>
-#ifdef PCIE
 	txbd_rdptr = <PCIE transmit read pointer>
 	txbd_wrptr = <PCIE transmit write pointer>
 	rxbd_rdptr = <PCIE recieve read pointer>
 	rxbd_wrptr = <PCIE recieve write pointer>
 	eventbd_rdptr = <PCIE event read pointer>
 	eventbd_wrptr = <PCIE event write pointer>
-#endif
 	cmd_resp_received = <0/1, no cmd response to process/response received and yet to process>
 	event_received = <0/1, no event to process/event received and yet to process>
-#ifdef USB
 	tx_cmd_urb_pending = <number of URB pending for cmd transmit>
 	tx_data_urb_pending = <number of URB pending for data transmit>
-#ifdef USB_CMD_DATA_EP
 	rx_cmd_urb_pending = <number of URB pending for cmd receive>
-#endif
 	rx_data_urb_pending = <number of URB pending for data receive>
-#endif
 	ioctl_pending = <number of ioctl pending>
 	tx_pending = <number of Tx packet pending>
 	rx_pending = <number of Rx packet pending>
 	lock_count = <number of lock used>
 	malloc_count = <number of malloc done>
 	mbufalloc_count = <number of mlan_buffer allocated>
-#ifdef PCIE
 	malloc_cons_count = <number of consistent malloc done>
-#endif
 	main_state = <current state of the main process>
-#ifdef SDIO_MMC_DEBUG
 	sdiocmd53w = <SDIO Cmd53 write status>
 	sdiocmd53r = <SDIO Cmd52 read status>
-#endif
-#if defined(USB_SUSPEND_RESUME) || defined(SDIO_SUSPEND_RESUME)
 	hs_skip_count = <number of skipped suspends>
 	hs_force_count = <number of forced suspends>
-#endif
 
-#if !defined(MLANUTL_LITE)
-#ifdef SDIO
 	Issue SDIO cmd52 read/write through proc.
 	Usage:
 		echo "sdcmd52rw=<func> <reg> [data]" > /proc/mwlan/adapterX/config
@@ -851,17 +294,13 @@
 		func: The function number to use (0-7)
 		reg:  The address of the register
 		data: The value to write, read if the value is absent
-#ifdef SDIO_MMC
 		For SDIO MMC driver, only function 0 and WLAN function access is allowed.
 		And there is a limitation for function 0 write, only vendor specific CCCR
 		registers (0xf0 -0xff) are permiited.
-#endif
 	Examples:
 		echo "sdcmd52rw= 0 4" > /proc/mwlan/adapterX/config      # read func 0 address 4
 		cat /proc/mwlan/adapterX/config                          # display the register value
 		echo "sdcmd52rw= 1 3 0xf" > /proc/mwlan/adapterX/config  # write 0xf to func 1 address 3
-#endif
-#endif /* !defined(MLANUTL_LITE) */
 
 	Issue debug_dump command through proc.
 	Usage:
@@ -869,36 +308,12 @@
 
 	Examples:
 		echo "debug_dump" > /proc/mwlan/adapterX/config      # dump driver internal debug status.
-#ifdef DUMP_TO_PROC
 	To obtain fw dump or driver dump, use command:
 	        cat /proc/mwlan/adapter0/drv_dump > file_drv_dump     #save the drv dump to file_drv_dump
 	        cat /proc/mwlan/adapter0/fw_dump > file_fw_dump       #save the fw dump to file_fw_dump
-#ifdef DUAL_MAC
             cat /proc/mwlan/adapter1/drv_dump > file_drv_dump_2   #save the adapter1 drv dump to file_drv_dump_2
-#endif
-#endif
 
 	Use dmesg or cat /var/log/debug to check driver debug messages.
-#ifdef CONFIG_X86
-	To log driver debug messages to file,
-	a) Edit /etc/syslog.conf, add one line "*.debug		/var/log/debug"
-	   on kernel 2.6.24 or later, edit /etc/rsyslog.conf instead
-	b) touch /var/log/debug (if the file doesn't exist)
-	c) service syslog restart
-	   on kernel 2.6.24 or later, service rsyslog restart
-#endif
-
-#ifdef DEBUG_LOG
-	To control the driver log buffer through the proc, the following command can be used.
-	Note: proc can only read at max kernel PAGE_SIZE - 1024 bytes.
-
-	Usage:
-		cat /proc/mwlan/adapterX/logctrl                         # To read driver log messages
-		echo "lock" > /proc/mwlan/adapterX/logctrl               # Lock the driver log buffer
-		echo "unlock" > /proc/mwlan/adapterX/logctrl             # Unlock the driver log buffer
-		echo "clear" > /proc/mwlan/adapterX/logctrl              # Clear the driver log buffer
-		echo "level=0xFF" > /proc/mwlan/adapterX/logctrl         # Set log buffer level to 0xFF
-#endif
 
 	Update /proc/sys/kernel/printk to change message log levels.
 	For example,
@@ -906,7 +321,6 @@
 	                                     will be printed to the console)
 	echo 15 > /proc/sys/kernel/printk   (all messages will be printed to console)
 
-#ifdef FW_RELOAD
 4) FOR FW RELOAD
     a) Enable parallel firmware download in driver parameter
        insmod sdxxx.ko fw_serial=0
@@ -918,16 +332,12 @@
        echo "fw_reload=1" > /proc/mwlan/adapterX/config   trigger SDIO inband firmware reset and reload firmware
        echo "fw_reload=2" > /proc/mwlan/adapterX/config   trigger firmware reload
        echo "fw_reload=3" > /proc/mwlan/adapterX/config   set firmware reload flag in driver.
-#ifdef PCIE
        echo "fw_reload=4" > /proc/mwlan/config   trigger PCIe FLR and reload firmware.
        echo "fw_reload=6" > /proc/mwlan/config   trigger PCIe inband firmware reset and reload firmware.
-#endif
 
     (Note: This feature will be supported on Robin3 and KF2.
            For CAC-A2, it only work with the board which supports parallel fw download)
-#endif
 
-#ifdef RF_TEST_MODE
 5) FOR RF test mode commands:
 
     Following commands are used to perform RF testing of the wifi chipset.
@@ -957,18 +367,14 @@
 
     Set Tx Antenna
 	For 1x1 chipsets, 1:Main, 2:Aux when antenna diversity is supported
-#ifdef STREAM_2X2
 	For 2x2 chipsets, 1:Path A, 2: Path B, 3: Path A+B
 			  Both Tx and Rx must be set to same antenna path
-#endif
 	echo "tx_antenna=1" > /proc/mwlan/adapterX/config
 
     Set Rx Antenna
 	For 1x1 chipsets, 1:Main, 2:Aux when antenna diversity is supported
-#ifdef STREAM_2X2
 	For 2x2 chipsets, 1:Path A, 2:Path B, 3:Path A+B
 			  Both Tx and Rx must be set to same antenna path
-#endif
 	echo "rx_antenna=1" > /proc/mwlan/adapterX/config
 
     Set RF band  (0:2G, 1:5G)
@@ -1068,7 +474,6 @@
     echo "trigger_frame=1 0 1 2 5484 0 256 0 0 0 1 0 0 0 1 60 1 0 65535 0 511 5 0 61 0 0 0 0 90 0 0 0 0"  > /proc/mwlan/adapter0/config
     echo "tx_frame=1 0x1102 0xabababab 200" >/proc/mwlan/adapter0/config
 
-
     OTP Read/Write
     Example: Read OTP MAC address.
     echo "otp_mac_add_rd_wr=0"  > /proc/mwlan/adapter0/config
@@ -1076,9 +481,6 @@
     Example: Write OTP MAC addres.
     echo "otp_mac_add_rd_wr=1 AA:BB:CC:DD:EE:FF"  > /proc/mwlan/adapter0/config
 
-#endif
-
-#ifdef HS_SUPPORT
 6) Set host sleep parameters
 
     hssetpara
@@ -1086,7 +488,6 @@
     Example:
         echo "hssetpara=2 0xff 0xc8 3 400" > /proc/mwlan/adapter0/config
         echo "hssetpara=2 1 0xc8 3 400 " > /proc/mwlan/adapter0/config
-#endif
 
 7) For Antenna Diversity Command
 
@@ -1096,42 +497,25 @@
         GET Command Format: cat /proc/mwlan/adapter0/config
         SET Command Format: echo "antcfg=[m] [n] [o] [p]" > /proc/mwlan/adapter0/config
 
-#ifdef STREAM_2X2
     For chip which support STREAM_2X2
     where value of m is:
         Bit 0   -- Tx Path A or Tx/Rx Path A if [n] is not provided
         Bit 1   -- Tx Path B or Tx/Rx Path B if [n] is not provided
         Bit 0-1 -- Tx Path A+B or Tx/Rx Path A+B if [n] is not provided
-#if defined(PCIE9098) || defined(SD9098) || defined(USB9098) || defined(PCIE9097) || defined(SD9097) || defined(USB9097)||defined(SDIW624)||defined(PCIEIW624)||defined(USBIW624)
         For 9097/9098/IW624, LOW BYTE for 2G setting
         Bit 8   -- Tx Path A or Tx/Rx Path A if [n] is not provided
         Bit 9   -- Tx Path B or Tx/Rx Path B if [n] is not provided
         Bit 8-9 -- Tx Path A+B or Tx/Rx Path A+B if [n] is not provided
         For 9097/9098/IW624, HIGH BYTE for 5G setting
-#endif
     where value of n is:
         Bit 0   -- Rx Path A
         Bit 1   -- Rx Path B
         Bit 0-1 -- Rx Path A+B
-#if defined(PCIE9098) || defined(SD9098) || defined(USB9098) || defined(PCIE9097) || defined(SD9097) || defined(USB9097)||defined(SDIW624)||defined(PCIEIW624)||defined(USBIW624)
         For 9097/9098/IW624, LOW BYTE for 2G setting
         Bit 8   -- Rx Path A
         Bit 8   -- Rx Path B
         Bit 8-9 -- Rx Path A+B
         For 9097/9098/IW624, HIGH BYTE for 5G setting
-#endif
-#ifdef ENABLE_802_116E
-    where value of o is:
-        For IW624, 6G setting
-        Bit 0   -- Tx Path A
-        Bit 1   -- Tx Path B
-        Bit 0-1 -- Tx Path A+B
-    where value of p is:
-        For IW624, 6G setting
-        Bit 0   -- Rx Path A
-        Bit 1   -- Rx Path B
-        Bit 0-1 -- Rx Path A+B
-#endif
     The Tx path setting (m) is used for both Tx and Rx if Rx path (n) is not provided.
 
     Examples:
@@ -1139,15 +523,9 @@
         echo "antcfg=3" > /proc/mwlan/adapter0/config           : Set Tx and Rx path to A+B
         echo "antcfg=1 3" > /proc/mwlan/adapter0/config         : Set Tx path to A and Rx path to A+B
 
-#if defined(PCIE9098) || defined(SD9098) || defined(USB9098) || defined(PCIE9097) || defined(SD9097) || defined(USB9097)||defined(SDIW624)||defined(PCIEIW624)||defined(USBIW624)
         echo "antcfg=0x103" > /proc/mwlan/adapter0/config           : Set Tx and Rx path to A+B on 2G and Tx and Rx path to A on 5G
         echo "antcfg=0x103 0x103" > /proc/mwlan/adapter0/config     : Set Tx path to A+B and Rx path to A+B on 2G, and Tx and Rx path to A on 5G
-#endif
-#ifdef ENABLE_802_116E
-        echo "antcfg=0x103 0x103 2 2" > /proc/mwlan/adapter0/config   : Set both Tx and Rx path to A+B on 2G, both Tx and Rx path to A on 5G, both Tx and Rx path to B on 6G
-#endif
 
-#if defined(PCIE9098) || defined(SD9098) || defined(USB9098)
         echo "antcfg=0x202" > /proc/mwlan/adapter0/config : Use 5GHz path B pin for 5G TX/RX and 2GHz path B pin for 2G TX/RX
 
         On RD board connection is as follows :
@@ -1155,9 +533,7 @@
         5GHz path B pin -> AntB
         2GHz path A pin -> AntB
         2GHz path B pin -> AntA
-#endif
 
-#ifdef FEATURE_CONTROL
     For chip which support SAD
         where value of m is:
         Bit 0   -- Tx/Rx antenna 1
@@ -1174,28 +550,4 @@
         echo "antcfg=0xFFFF" > /proc/mwlan/adapter0/config            : Set Tx/Rx antenna diversity
         echo "antcfg=0xFFFF 0x1770" > /proc/mwlan/adapter0/config     : Set antenna evaluate time interval to 6s
 
-#endif
-
-#else
-    This command is used to set/get the mode of Tx/Rx antenna.If SAD is enabled,
-this command can also used to set SAD antenna evaluate time interval(antenna mode must
- be antenna diversity when set SAD evaluate time interval).
-
-
-    where value of m is:
-        Bit 0   -- Tx/Rx antenna 1
-        Bit 1   -- Tx/Rx antenna 2
-        ...
-        0xFFFF  -- Tx/Rx antenna diversity
-
-        where value of n is:
-                if m = 0xFFFF, SAD evaluate time interval,default value is 6s(0x1770)
-
-    Examples:
-        cat /proc/mwlan/adapter0/config                                : Get Tx/Rx antenna mode
-        echo "antcfg=1" > /proc/mwlan/adapter0/config                : Set Tx/Rx antenna 1
-        echo "antcfg=0xFFFF" > /proc/mwlan/adapter0/config            : Set Tx/Rx antenna diversity
-        echo "antcfg=0xFFFF 0x1770" > /proc/mwlan/adapter0/config     : Set antenna evaluate time interval to 6s
-
-#endif